간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제14권 제6호 (2012년 12월) 16건
학술연구
1.
2012.12
구독 인증기관 무료, 개인회원 유료
In this study, the structural analysis for bellows joint of high-performance that can enhance the performance of seismic isolation piping was performed. Bellows joint is that the corrugated flexible piping is connected at the both sides of elbow. An one axis of the bellows joint fixed, and the other end of the axis changes the position from 0° to 315° for the radius displacement of 500 mm. Results obtained are as follows for this case in analysing of the maximum stress and plastic strain of the bellows joint. As the location of the base isolation displacement get farther from the fixed pipe, the bellows joint is pulled, and the maximum stress and plastic deformation is increased. And so the maximum stress occurs near the bellows at both ends of the elbow. Displacement in the 135° position, a maximum stress of 837 MPa and a plastic strain of 3.00% was the highest.
4,000원
2.
2012.12
구독 인증기관 무료, 개인회원 유료
본 연구는 마이크로 스케일의 내부 구조를 갖는 3차원 인공지지체를 제작하기 위하여 개발된 제조 시스템의 성능 분석을 위해 x-y축 정밀 스테이지 시스템으로 조립되었을 때의 해상도 및 정확도를 측정 하였으며, z축 정밀 스테이지를 분리하여 다양한 물리적 오차를 제거하였다. 기존의 x-y-z축 정밀 스테이 지 시스템을 x-y축으로 분리하고 각 축의 이동거리를 4종류(±0.25μm, ±0.5μm, ±25μm, ±50μm)로 설정하여 각 위치마다의 변위를 레이저 측정기를 이용하여 기록하였다. 가장 작은 이동거리(±0.25μm)에서의 진동이 상대적으로 가장 크게 나타났으며, y축 스테이지 위에 x축 스테이지를 조립하였기 때문에 x축 스테이지 자중에 의한 모멘텀으로 인하여 y축 스테이지 구동변위 값이 크게 나타났다. 하지만 z축 스테이지는 기존 시스템과 달리 별로도 분리하여 구동 오차를 줄였으며, 일체화된 광학시스템을 적용하여 광학오차를 감 소시켰다. 따라서 새로운 시스템에서는 500μW, 140mm/min의 가공조건에서도 마이크로 스케일의 3차원 인 공지지체 형상의 구조물을 성공적으로 제작할 수 있었다.
4,000원
3.
2012.12
구독 인증기관 무료, 개인회원 유료
This paper is to study the energy absorption characteristics of CF/Epoxy(Carbon Fiber/Epoxy Resin) laminated shell with the various curvatures subjected to transverse impact loadings under the low impact velocity in consideration of design of structural members for use of transportation machine, which are consisted of the characteristics of high stiffness, strength and lightweight. The curvature radius are associated with the energy absorption characteristics of CF/Epoxy laminated shell which is brittleness material. In all tests, maximum load of CF/Epoxy laminated plate is higher than that of laminated shell with curvature, but maximum deflection is lower. And then absorbed energy of laminated shell with curvature is higher than laminated plate(curvature radius is unlimited). As curvature radius is increased, the absorbed energy is increased in laminated shell with curvature.
4,000원
4.
2012.12
구독 인증기관 무료, 개인회원 유료
The object of this project is to prepare the countermeasure of the health care according to investigate and database the basic information of the large machine and high power machine. To accomplish the object; The dimension and noise of the large machine, which is mounted in the factory, was investigated. The prediction and measurement method of the noise for the machine by manufacturers were investigated. The noise at the 500 points of the large machine and high power machine in the 40 processes of the 6 factories, 6 business fields was measured. The database of the noise was built from the measurement data. The major sound sources and frequency range for the large machine and the high power machine were investigated. The noise effect by the large machine and the high power machine was investigated.
4,000원
5.
2012.12
구독 인증기관 무료, 개인회원 유료
Recently, national attention on the regulations for carbon dioxide emission has risen. Thus, diverse attempts are being actively carried out to reduce the resistance of ships and to develop a new propelling system that reduces the emission of carbon dioxide. This study presents to induce a way to utilize the generated wind power for the electrical energy source of a ship’s lighting, air conditioning and heating by installing a compact wind power facility on the experiment target; a small size high-speed vessel. The vessel targeted for application is a 30ft high-speed leisure boat made of aluminum alloy. The wind power facility installed on the hull and the batteries that will be charged by the electric energy generated by the wind power system were considered at the designing stage of the boat. A new presumption equation for air resistance of wind turbines and efficient measures for management are suggested based on a model test that verifies the basic performance of the wind-powered leisure boat.
4,000원
6.
2012.12
구독 인증기관 무료, 개인회원 유료
Aluminum foam with porous material has the excellent mechanical property of light weight and impact absorption. It is necessary to obtain the information of fracture toughness at the adhesive work by the joint method. This study is investigated by fatigue analysis with DCB(Double Cantilever Beam) specimen models to evaluate the strengths at adhesive joints on the basis of British industrial and ISO international standards. 4 kinds of specimens are modelled by changing the height of specimen and the analysis results are compared with each other. As the height of specimen becomes lower, the displacement on the y direction, load and energy release rates become higher. Through the correlation obtained by this study result, fracture behaviors are examined and mechanical properties can be understood. Aluminum foam material bonded with adhesive can applied to the real composite structure by use of this study result.
4,000원
7.
2012.12
구독 인증기관 무료, 개인회원 유료
Numerical Analysis of the Effect of GDL Porosity and Cathode Inlet Humidity on the PEMFC Performance
In this paper, the PEMFC performance was studied using three dimensional numerical analysis. The effect of GDL porosity and cathode inlet humidity on the cell polarization curve was analyzed. The GDL porosity of 0.3, 0.5, 0.7 and cathode inlet humidity of 20, 40, 60, 80, 100 percent were selected as simulation cases while the anode inlet humidity was maintained as 100 percent. For a constant cell voltage condition, the highest current density was obtained at GDL porosity of 0.7 and cathode inlet humidity of 20 percent. As GDL porosity increases, the amount of hydrogen diffusion to membrane from the anode increases and chemical reaction also increases. As cathode inlet humidity decreases, oxygen mass fraction of cathode gas channel increases and chemical reaction also increases.
4,000원
8.
2012.12
구독 인증기관 무료, 개인회원 유료
The annual energy demand of the standard rural house models Nongrim-10-26 -ga was analyzed using the DesignBuilder. Size of window and type of window were selected as simulation parameters. As a result, heating energy demand was 8.3 times higher than cooling energy demand and reducing heating energy demand is important factor in reducing total building energy. When increasing window glazing size, internal heat gain and loss was changed depending on the outdoor weather conditions. Cooling energy demand increases in summer and heating energy demand increases in winter. When the type of window was changed, cooling energy demand was decreased as the SHGC value was decreased. However, heating energy demand was changed depending on both of the SHGC value and U-value of the selected window type.
4,000원
9.
2012.12
구독 인증기관 무료, 개인회원 유료
The EnergyPlus is used for the analysis of energy demand at two rural house models. Photovoltaic (PV) system is installed to reduce the energy demand of annual building. The energy economic analysis is performed to provide quantitative data at choosing a suitable house model. Two types of PV system installations are considered as each building type. Among 4 different cases analyzed through this study, the best setup is provided for 12.3 years at recovering PV system installation cost.
4,000원
10.
2012.12
구독 인증기관 무료, 개인회원 유료
This paper presents a new feature representation method, named two- dimensional orthogonalized Fisher discriminant analysis(2D-OFD). The method adopts the 2D-LDA and orthogonalization of Fisher vector. It produces the small size scatter matrix than 1D method. Therefore it can evaluate the scatter matrix accurately. In addition, it is not suffered from small sample size problem. The orthogonalization eliminates the linear dependences among Fisher's discriminant vectors. As a result, it promotes the discriminant capability of the 2D-LDA. The proposed method is tested on the ORL face image database. We test our method 10 times. For each experiment, five training images are randomly chosen each person and the other five images are used for testing. The test show that the average recognition rate is 96.2%. When the image is downsampled to 28x23 matrix to reduce the computational complexity, the average recognition rate is 95.9%.
3,000원
11.
2012.12
구독 인증기관 무료, 개인회원 유료
본 논문에서는 단일 센서와 공간집속 신호처리 기술로 시간 역전과 인버스 필터링을 이용하여 등방성 평판에 서 충격 위치를 결정할 수 있는 탐상법을 다루었다. 유한 평면에서 굽힘 파의 운동 방정식을 유도하여, 그 식을 통해 얻어진 데이터를 기반으로 해석적인 시뮬레이션을 통해 시간 역전과 인버스 필터링의 시간 집속 효과를 확 인하고 충격 위치와 그 주변에서 신호의 공간 집속 효과를 관찰하고 충격 위치 결정에 영향을 미칠 수 있는 인자 들(총 수신시간, 샘플링 주파수)에 대해 살펴보았다. 그리고 충격원의 위치에 따른 2차원 결과를 제시하고, 실제 충격 위치를 정확하게 결정할 수 있음을 확인하였다. 여기서 제안한 방법은 기존의 충격 위치 결정법에 비해 많 은 장점을 갖고 있다. 첫 번째로 단일 센서를 사용하는 것과 시험체의 형상과 물성을 몰라도 된다는 점이다. 또한 판 에서와 같이 분산성에 의한 다중모드 파동이 발생하는 경우에도 특정 모드나 주파수에 의존할 필요가 없다.
4,000원
12.
2012.12
구독 인증기관 무료, 개인회원 유료
본 논문에서는 단일 센서와 공간집속 신호처리 기술로 시간 역전과 인버스 필터링을 이용하여 이방성 평판에 서 충격 위치를 결정할 수 있는 탐상법을 다루었다. 유한 평면에서 굽힘 파의 운동 방정식을 유도하여, 그 식을 통해 얻어진 데이터를 기반으로 해석적인 시뮬레이션을 통해 시간 역전과 인버스 필터링의 시간 집속 효과를 확 인하고 충격 위치와 그 주변에서 신호의 공간 집속 효과를 관찰하고 충격 위치 결정에 영향을 미칠 수 있는 인자 들(총 수신시간, 샘플링 주파수)에 대해 살펴보았다. 그리고 충격원의 위치에 따른 2차원 결과를 제시하고, 실제 충격 위치를 정확하게 결정할 수 있음을 확인하였다. 여기서 제안한 방법은 기존의 충격 위치 결정법에 비해 많은 장점을 갖고 있다. 첫 번째로 단일 센서를 사용하는 것과 시험체의 형상과 물성을 몰라도 된다는 점이다. 또한 판 에서와 같이 분산성에 의한 다중모드 파동이 발생하는 경우에도 특정 모드나 주파수에 의존할 필요가 없다.
4,000원
생산기술
13.
2012.12
구독 인증기관 무료, 개인회원 유료
Fluid frictional hot-water system consisted of power supply equipment, a motor, fluid heater, fluid tank, circulating pump, fan, flow meter and a heat exchanger. The system had a motor of power capacity 15.2kw/h, light-oil hot air heater in control plot had the heating capacity 20,000kcal/h, by the performance test result, it could supply heat from 24.6 to 28.1 kw depending on the motor, respectively. Thermal efficiency of fluid frictional heater were 88.1% to 91.0% in the same conditions. As the result, a deviation of indoor air temperature between the treatment plot and the control plot was about 2℃. It was heating cost of the each system heater and light-oil hot air heater heating cost were 742,200won, 2,266,000won. therefore heating cost saving was 67%. Yield of tomato cultured in greenhouse with fluid frictional hot-water system was high as 4%. As a result, the fluid frictional hot-water system was 48% higher in economics than the hot air heater.
4,000원
14.
2012.12
구독 인증기관 무료, 개인회원 유료
Appliances are connected with home network and intellectualization is being rapidly processed. As ubiquitous home is visualized, home sensor is intellectualized and developed with wearable form for the possible inter-home sensor information exchange. Based on the RFID and ubiquitous ID, the home sensors are expected to be developed for the diverse information. The sensor techniques has been intellectualized and diversified by expecting to be developed into perception sensor, extreme environment sensor, micro mechanical sensor, and biosensor. In this paper, the control algorithm of digital control system applicable to the real appliance is suggested. Infrared ray module of appliance is used with the purpose in supporting home network to the appliance in use. And the wireless sign transmitted from home server is transformed into infrared rays sign.
4,000원
15.
2012.12
구독 인증기관 무료, 개인회원 유료
When gasoline car using gasoline additives and lubricant additives was running, we were able to find the characteristics which is related to noise and vibration, and also affection of emission by chassis dynamometer. The results are followed. 1) change of HC was not related to lubricant additives, it turned out that change of HC will be low, when ratio of gasoline additives is high. 2) NOx was detected to high, when ratio of lubricant additives is high. And when ratio of gasoline additives was 8.29, the data for NOx was lowest. 3) CO2 was 13.5～14% constantly, this result is not related to ratio of lubricant additives and gasoline additives. 4) Noise was not related to both of them ratio of lubricant additives and gasoline additives. But vibration was downed to 120Hz at 40km/h due to lubricant additives.
4,000원
