Recently, the pipeline system for waste transportation has been increasingly constructed as new solution for the waste collection and disposal system by constantly increasing domestic waste which issued as social problem. The pipeline system is constructed through long distance, so proper long-term monitoring system is necessary which available to detect the damage location for the effective maintenance. In this paper, the experimental study is carried out to evaluate the applicability of optical strain gauge sensor based on FBG for the long-term monitoring system. Three test parameters such as pressure leaking, blockage and deformation are considered as typical damages for real-scale pipeline test specimen. In order to measure flexural and volumetric strain and temperature, three FBG sensors are installed at each monitoring sections. From the test results, this study suggested effective methods of sensor installation and arrangement. Also the sensor spacing for the design of monitoring system using FBG sensor is derived by the correlation of distances from deformation between sensor responses.
Floor damping materials used in floating floor system to diminish the floor noise have been made with low density and dynamic stiffness. Owing to this low density and dynamic stiffness, the deflection in these materials under long-term loading and cracking of the floor finishing mortar in the floating floor system may occur. This paper presents the results of long-term loading effects on the deflection of different types of floor damping materials. The experimental program involved the long-term loading tests for 490 days loading period on sixteen specimens. Specimens were classified as DM1(Damping Materials) to DM8, depending upon the four main parameters; types, bottom shapes and densities of floor damping materials and amount of loading. Results indicated that the long-term deflection of all specimens of damping materials remained unchanged after 200 days at all loading amounts, except the specimens made up of Polystrene, in which long-term deflection remained unchanged after 160 days at 250 N load and 100 days 500 N load. In this paper, two types of correlation expressions were shown in the deflection range prior to the range where deflection remained constant; two analyses by ISO 20392 and linear regression. In comparison of two analyses and experimental results on the difference of deflection of 16 specimens, the difference of deflection was below 0.4 mm in those analyses in case of that total deflection was below 10 mm. Restrictively, it was judged that the analysis for the deflection of specimens made up of Polystrene is more appropriate using ISO 20392.
Background : Aralia cordata and Polygonum multiflorum GAP cultivation requires a stable drying and storage settings after harvesting. therefore, this experiment was performed in order to effectively manage the physical, chemical and biological hazards. Methods and Results : Test materials were used biennial Aralia cordata, Polygonum multiflorum harvested from the medicinal testing ground. The drying temperatures were treated with 40, 50, 6 0℃ and natural drying. Storage containers were stored in plastic boxes, styrofoam boxes and kraft paper containers, examined the color and quality changes for eight months. Aralia cordata and Polygonum multiflorum drying temperature is dry it took natural drying 720 hours, 40℃ hot air drying 180 hours, 50℃ hot air drying 168 hours and 60℃ hot air drying 108 hours. However, the difference chromaticity of the Lab value corresponding to the temperature does not appear, it was good to dry in a short time at 60℃. Aralia cordata and Polygonum multiflorum stored in a styrofoam box storage method but can be stored at room temperature for up to four months, began to decay caused by moisture content it continues to increase. In plastic box in case of Aralia cordata and kraft vessel in case of Polygonum multiflorum can be stored for eight months in room temperature without decay. Styrofoam boxes stored at 5℃ cold storage were higher water absorption such as room temperature, but decay did not occur. Plastic box and styrofoam box were a tendency such as room temperature. Conclusion : Aralia cordata and Polygonum multiflorum are thought that the color change is not large depending on the drying temperature the lower the water content. Styrofoam storage box, the air permeability is higher than plastic boxes and containers Kraft vessel, decay occurs expected increase.
The purpose of this study was to investigate deformation and reduction of initial clamping force in slip critical type connection under fatigue loading. And, the parameters of this study were the different clamping force and friction coefficient of surface of plate. As a result, the clamping force of all specimens were generally decreased in comparison with initial values under fatigue loading.
Accelerated alkali resistance test were conducted for pre-heated GFRP Rebar. The GFRP rebar specimens were heated to temperatures of 60℃, 120℃, 200℃ and 300℃ and then immerged in alkali solution for 30days. According to ACI 440.3R-12, tensile properties were measured.
This study focused on whether the large-scale expansion joints of the Diamond Bridge, a suspension bridge, is being appropriately and efficiently utilized during maintenance period. In this study, a linear regression model was developed by analyzing long-term monitoring data from the bridge, considering the bridge design standards in Korea and building-related literatures. Then, the reliability of the model was verified through a theoretical review on the relationship between temperature change and expansion joint displacement. The expansion joint displacements of the bridge showed a regular time series graph with temperature change. A linear regression analysis indicated that the slope of the graph was very similar to the displacement of steel due to linear expansion coefficient, with a high determination coefficient (R2=0.979), meaning that the actual behavior of the bridge conforms to the theory. Considering the expansion joint specification of the bridge and existing external loads, actual expansion joint displacement was only 8.5 percent of its specification, so the specification can be adjusted in order that actual expansion joint displacement can be up to 21.6 percent of its specification. In this case, expansion joint cost can be reduced as much as 78.4 percent of its original cost.
In this study, the behavior of the existing tunnel was measured by automation system to analyze the characteristics of lining longitudinal cracks. The characteristic of the infusion material which it is applicable to crack repairing was considered by grasping the overall behavior including the temperature and the crack width change, and etc., From this, the reasonable repair period for the complement efficiency enhancement was trying to be determined.
Recently, there are increasing cases utilizing the composite slab with a deck-plate for the simplicity of construction process and shortening of the construction period by eliminating the formwork and reinforcement placing works. General method of an existing deck-plate slab places welded wire fabric(w.w.f) for the crack control by drying shrinkage, however it was pointed out as its potential possibility for a number of cracks. In this study, long-term cracking behavior of deck-plate slab with the steel fiber was evaluated on the continuous two-span slab specimens that was designed on the general building loading condition.
A long-term field experiment under different fertilization treatments had been conducted to explore the effects of rice yield and soil chemical properties from 1978 to 2008 in Suwon, Korea. The paddy was applied eight fertilization treatments which were F0 (no fertilizer), PK (phosphorous and potassium), NK (nitrogen and potassium), NP (nitrogen and phosphorous), NPK (nitrogen, phosphorus and potassium), NPKC (NPK with compost), NPKS (NPK with straw) and NPKL (NPK with lime). Results of 31 years experiment showed that yield index (the ratio of yield in each treatment to NPK) was the lowest in F0 (0.52) and the highest in NPKC (1.18). Yield index was gradually increased in NPKC but decreased in F0 and NK. The yield index of PK, NP, NPKS and NPKL were not changed long-term treatment. Soil acidity of NPKL showed the highest with pH 7.9, and that of other treatments ranged from pH 6.3 to 6.8. Available phosphorous content of soil was increased in all plots by long-term fertilization, was the highest in PK and NPKC. Soil organic matter was higher in NPKC (1.8%) and NPKS (1.8%) than other treatments (1.3~1.4%) in the early experiment, but that was remarkably increased in only NPKC (2.5%) according to annual long-term application. Thus we suggest that annual compost application with optimum NPK could make stable and sustainable rice production.
경부 고속철 40 m 단경간 PSC 교량을 대상으로 38 자유도 KTX 동력차를 주행속도 500 km/h까지 12 단계 불규칙 궤도형상과 상호 작용력을 고려하여 해석하였다. 차량의 윤축하중과 중심회전각을 평가하기 위하여 170 m 일반도상을 교량과 조합하여 횡압과 탈선계수 그리 고 윤중감소율을 허용기준과 비교하였다. 단순교와 연속교의 교량받침 최대 변위와 누적이동거리를 주행속도별로 해석하였다. PTFE 마찰판 과 DP-mate의 EN-1337-2 기준의 장기마찰시험을 수행하였다. 수행된 장기마찰시험은 차세대 고속철의 증가되는 주행속도를 고려하여 개선 방안을 제안하였다.
The government has conducted a plan of total maximum daily loads(TMDL), which divides with unit watershed, for management of stable water quality target by setting the permitted total amount of the pollutant. In this study, BOD concentration trends over the last 10 years from 2005 to 2014 were analyzed in the Geumho river. Improvement effect of water quality throughout the implementation period of TMDL was evaluated using the seasonal Mann-Kendall test and a LOWESS(locally weighted scatter plot smoother) smooth. As a study result of the seasonal Mann-Kendall test and the LOWESS smooth, BOD concentration in the Geumho river appeared to have been reduced or held at a constant. As a result of quantitatively analysis for BOD concentration with exploratory data analysis(EDA), the mean and the median of BOD concentration appeared in the order of GH8 〉GH7 〉GH6 〉GH5 〉GH4 〉GH3 〉GH2 〉GH1. The monthly average concentration of BOD appeared in the order of Apr 〉Mar 〉Feb 〉May 〉Jun 〉Jul 〉Jan 〉Aug 〉Sep 〉Dec 〉Nov 〉Oct. As a result of the outlier, its value was the most frequent in February, which is estimated 1.5 times more than July, and was smallest frequent in July. The outlier in terms of water quality management is necessary in order to establish a management plan for the contaminants in watershed.
Long-term variations of PM10 and the characteristics of local meteorology related to its concentration changes were analyzed at 4 air quality sites (Ido-dong, Yeon-dong, Donghong-dong, and Gosan) in Jeju during two different periods, such as PI (2001-2006) and PII (2007-2013), over a 13-year period. Overall, the long-term trend of PM10 was very slightly downward during the whole study period, while the high PM10 concentrations in PII were observed more frequently than those in PI. The concentration variations of PM10 during the study period was clarified in correlation between PM10 and meteorological variables, e.g. the low (high) PM10 concentration with large (small) precipitation or high (low) radiation and in part high PM10 concentrations (especially, Donghong-dong and Gosan) with strong wind speed and the westerly/northwesterly winds. This was likely to be caused by the transport effect (from the polluted regions of China) rather than the contribution of local emission sources. The PM10 concentrations in “Asian dust” and “Haze” weather types were higher, whereas those in “Precipitation”, “Fog”, and “Thunder and Lighting” weather types were lower. The contribution of long-range transport to the observed PM10 levels in the urban center (Ido-dong, Yeon-dong, and Donghong-dong), if estimated by comparison to the data of the background site (Gosan), was found to explain about 80% (on average) of its input.
미계측유역의 유출량 모의는 수문학 분야에서 필수적인 사항이다. 강우-유출 모형을 이용하여 신뢰성 있는 유출량을 모의하기 위한 핵심사항은 강우-유출 모형의 매개변수를 추정하는 것이다. 하지만 현재 우리나라는 불충분한 수문자료로 인해 매개변수 추정에 어려움이 존재한다. 본 연구의 목표는 불확실성 반영을 위한 Bayesian 통계기법 기반의 강우-유출 모형의 매개변수를 지역화 하는 것이다. 그 방법은 다음과 같다. 첫째, 본 연구는 세계적으로 널리 사용되고 있는 Sacramento 강우-유출 모형에 Bayesian Markov Chain Monte Carlo 기법을 연계한 Bayesian Sacramento 강우-유출 모형을 사용하여 계측유역을 대상으로 13개 매개변수를 최적화하고 각 매개변수의 사후분포를 도출하였다. 둘째, 매개변수와 유역특성인자 사이에 회귀특성을 얻기 위해 다중선형회귀분석을 적용하여 유역특성을 고려한 지역화 매개변수를 결정하였다. 다중회귀분석을 통하여 산정된 지역화 매개변수를 계측유역에 전이하여 유출량을 모의 후 통계적 효율기준인 N-S계수, 일치계수 및 상관계수를 사용하여 지역화 매개변수 검증을 수행하였다.
고속철 PSC 교량받침의 장기 마찰시험은 EN1337-2와 CUAP03.01/78기준을 기반으로 동일한 수직압력에 대한 온도변수별 누적 마찰거리 25,000 m 장기마찰시험을 수행하였다. 기존의 PTFE판은 우수한 마찰계수 결과에도 불구하고 10,000 m에서 손상되어 한계 내구성능을 나타 내었고, 반면에 DP-Mate판은 일부 온도구간에서 한계 마찰계수를 상회하였으나 성공적으로 장 기마찰시험을 만족시켰다. 개발된 마찰시험장치를 이용하여 온도변화(-35℃~70℃)내 저속(0.4 mm/s)시험 12 Cycle과 상온 고속(15 mm/s)시험 11 Cycle 을 32 일간 수행하였다.
국내 4대강에 설치된 다기능보는 하천을 횡단하는 수공구조물로써 고정보와 가동보로 구분되어 설치되었으며, 각 다기능 보의 수문운영 방식에 따라 유량이 변화하여 하상변동 및 유사이동 형태의 변화 가능성이 있다. 본 연구에서는 다기능보의 수문운영에 따른 장기 하상변동을 금강유역을 중심으로 연구하였다. 연구결과, 금강에서는 다기능보의 설치 및 수문운영 시나리오에 따라서 최심하상고의 변화가 연평균하상고의 변화에 비해서 상대적으로 큰 것으로 나타났다. 최심하상고의 하상저하는 최대 2.79 m, 하상상승은 최대 1.90 m까지 발생하는 것으로 나타났으며, 연평균하상고의 하상저하는 최대 2.16 m, 하상상승은 최대 1.24 m까지 발생하는 것으로 나타났다. 또한 하상변동에 따른 홍수위 분석 결과, 다기능보 설치 후에 홍수위가 대부분 상승하는 것으로 나타났으며, 최대 2.23 m까지 상승하는 것으로 나타났다. 이러한 결과로 인해서 제방의 여유고를 상회하는 홍수위가 발생할 가능성이 있기 때문에, 하천의 유사관리 및 하천계획수립을 함에 있어서 다기능보의 수문운영을 고려해야 한다고 판단된다. 또한 본 연구결과는 향후 하천계획을 수립함에 있어서 종단적 하도관리 및 안정하상 채택 등을 위해서 기초자료로 활용될 수 있을 것으로 본다.
최근 기후변화 및 4대강 보에 의한 본류 구간에서의 조류 발생 우려로 인하여 지류로부터 유입되는 영양염류 물질 등 비점오염에 대한 관리의 필요성이 증대되고 있다. 이와 같이 영양염류의 다량 유입 등 원인제공에서 대 조류 발생과 같은 수질현상으로 발현되기까지 장기간이 소요되는 경우, 오염원의 입체적 관리 및 사전예방 대책 수립을 위한 장기 수질예보의 필요성이 높아지고 있다. 국내의 경우 「수질예보 및 대응조치에 관한 규정」에 따라 현재 국립환경과학원에서는 4대강 본류 중심의 7일 단위의 단기 수질예보를 수행하고 있으며, 해외의 경우에도 장기 수질예보의 사례를 찾아보기 힘들다. 본 연구에서는 3개월 선행예측기간(lead time)의 장기 수질예보를 위해서 통계적 접근 방법과 모델링 기반 접근 방법의 예측성을 비교하였다. 통계적 접근 방법의 경우 관측자료 기반 기후인자(Climate Index)와 중권역 규모 관측 수질 사이의 지체시간(lag time)을 갖는 원격상관(teleconnection)을 이용하여 모델링 과정 없이 수질을 예측하였다. 반면 모델링 기반 방법의 경우에는 장기 기후예측 정보를 유역규모 및 일 단위로 시·공간적 상세화(downscaling)를 거쳐 유역모형의 입력으로 사용하여 수질을 예측하였으며, 유역모형으로는 국내에서 가장 보편적으로 사용되고 있는 Soil and Water Assessment Tool (SWAT) 및 Hydrological Simulation Program-Fortran (HSPF) 모형을 사용하였다. 낙동강의 위천 중권역을 대상으로 하여 총질소(TN) 및 총인(TP) 수질항목에 대한 예측성을 평가하였다. 통계적 방법의 경우 3개 관측지점에서 월별(12개월) 수질 장기 예측을 수행한 결과 유의수준 0.05에서 유의미한 상관계수(Temporal Correlation Coefficient) 이상의 값을 보인 경우는 TN, TP의 경우 각각 83%, 89%로서 적절한 예측성을 보였다. 반면 모델링 방법의 경우에는 수질의 절댓값(농도) 비교를 통한 예측성 평가에는 어려움이 있는 것으로 나타났으며, 향후 추가적인 예측성 평가 기법의 개발이 필요할 것으로 사료된다.
하천에 설치된 보와 같은 구조물은 하천의 수리적 특성을 변화시켜 보의 상류부에는 퇴적과 하류부에는 침식이 진행되어 단·장기적인 하상의 변화를 가져온다. 특히 우리나라의 경우 4대강 사업으로 국가하천의 과도한 준설로 인한 하천의 평형상태가 파괴되고 다시 평형상태를 복원하기 위한 하천의 침식과 퇴적작용으로 하상변동 발생이 예상되므로 단·장기적인 하상변동의 양상을 예측하고 분석하는 연구가 필요하다.
따라서 본 연구에서는 금강 중·하류부에 건설된 세종보 상류 약 600m 구간에 대해 하상변동 변화를 실측하였으며 실측결과와 2차원 수치모형인 SED-2D를 이용하여 흐름특성 및 하상변동을 모의한 결과를 비교하여 모형의 적용성을 평가하고 세종보 건설 시점을 기준으로 건설 1년, 5년, 10년 후의 단·장기적인 하상변동 양상을 분석하였다. 그 결과 세종보 건설 1년 후 상류 600m 구간에 169,263㎥의 토사가 퇴적되었으며 세종보 건설 5년 후에는 108,808.0㎥의 토사가 퇴적되었으며 세종보 건설 10년 후에는 63,713.5㎥의 토사가 퇴적되었다. 가동보 수문 개도 시 빠른 유속의 영향으로 보 직상류의 퇴적양은 적은 것으로 모의되었다. 세종보 상류의 하상변동 양상은 세종보 상류부 전체적으로 퇴적되는 경향을 보였으며 특히 우안에 집중적으로 퇴적 현상이 발생하였다. 이는 우안의 오목한 지형적 특성으로 인한 정체구역으로 유속이 낮게 모의되어 퇴적현상이 집중되는 것으로 분석되었다.
본 연구에서는 강우레이더강우자료의 수문학적 적용성을 평가하기 위하여 지상강우자료와 강우레이더자료를 준분포형 수문모형인 SWAT모형에 강우입력자료로 이용하여 낙동강 감천 유역에 대한 일유출모의를 수행하였다. 강우레이더자료는 단일편파레이더변수(Z)를 이용한 강우자료(RZ)와 이중편파레이더변수(Z,ZDR,KDP)를 이용한 강우자료(RKDP)두 가지 형태로 생성하였다. 분석기간은 2010년부터 2013년 7월까지로 각각 보정기간(2010년), 검증기간(2011년), 모의기간(2012년~2013년 7월)으로 구분하여 모의를 수행하였다.
10분단위의 지상강우자료와 2.5분 단위의 강우레이더자료를 SWAT모형에 입력자료로 활용하기 위하여 일강우자료로 변환하여 강우량을 비교한 결과 6월~9월(집중호우 및 태풍이 발생하는 우기)에는 강우발생특성을 잘 반영하고 있으나, 10월~5월(겨울 및 건기)에는 레이더관측강우가 과대추정하는 경향를 보여주었다. 그리고 지상강우자료와 강우레이더자료가 SWAT 모형의 일유출량에 미치는 영향에 대해 분석결과 지상강우자료가 강우레이더자료보다 유출특성을 더 잘 반영하였고, 레이더강우자료에서는 RKDP가 RZ보다 더 나은 결과를 나타냈다. 그러나 강우레이더강우자료의 활용에 앞서 보정과 실시간 알고리즘 적용 등 정확도 확보가 우선되어야 할 것으로 판단된다.