Juvenile xanthogranuloma (JXG) is a benign histiocytosis that occurs in the pediatric population. Cutaneous JXG is the most common form, while extracutaneous lesions, including oral JXG, is extremely rare. Cutaneous JXG can occur as multiple lesions and may have systemic visceral involvement, but this is not seen in oral JXG. In this case, we report a solitary oral JXG at the gingiva in a 3-year old male.

This study used a packed column reactor and a horizontal flow mesh reactor to examine the removal of copper ions from aqueous solutions using pine bark, a natural adsorbent prepared from Korean red pine (Pinus densiflora). Both equilibrium and nonequilibrium adsorption experiments were conducted on copper ion concentrations of 10mg/L, and the removals of copper ions at equilibrium were close to 95%. Adsorption of copper ions could be well described by both the Langmuir and Freundlich adsorption isotherms. The bark was treated with nitric acid to enhance efficiency of copper removal, and sorption capacity was improved by about 48% at equilibrium; mechanisms such as ion exchange and chelation may have been involved in the sorption process. A pseudo second-order kinetic model described the kinetic behavior of the copper ion adsorption onto the bark. Regeneration with nitric acid resulted in extended use of spent bark in the packed column. The horizontal flow mesh reactor allowed approximately 80% removal efficiency, demonstrating its operational flexibility and the potential for its practical use as a bark filter reactor.

Microorganisms detected in the biofilm not only cause secondary pollution of drinking water such as taste, odor and pathogenic disease but also increase the amount of disinfectant due to microbial regrowth during the transportation of tap water. In this work, the influence of C/N ratio in tap water on the characteristics of biofilm growth was examined. The C/N ratio of the tap water sample was controlled at 100:5, 100:10, 100:20, 100:30, and 100:40 by adding appropriate amounts of dextrose and (NH4)2SO4. Of the five C/N ratios, heterotrophic plate counts (HPC) was highest at the ratio of 100:10. Following the initial formation in all the five experimental conditions, natural detachment of the biofilm was observed. Extracellular enzyme activity (EEA) analyses showed that the change of the EEA during the experimental period was similar to that of the HPC, demonstrating a positive correlation between HPC and EEA. For TOC concentration in the tap water sample, approximately 75% of the TOC was consumed in 7 days of the experiment and 96% in 28 days. The TOC appeared to be relatively rapidly consumed at the initial phase of the biofilm growth. Consumption pattern of the ammonia nitrogen was different from the TOC consumption pattern showing the different role of ammonia nitrogen on the growth of biofilm.

The waterworks company is in charge of managing water facilities buried underground, and the management has been centered on manholes. However, since there is no standard management manual, it has been impossible to introduce and operate a systemized managing tool by water service providers and managers, and manhole management has been carried out by individual data recording personnel for each water service provider. When the management is carried out individually, the data to be shared by other waterworks managers tend to be privatized, and consequently, it may become a big obstacle to proceed with many civil works such as emergency leak repair, road excavation, replacement of old buildings. This report introduces RFID (Radio Frequency Identification) system which is based on the magnetic field capable of IOT. It also describes the necessity of leveraging the system for smart managing of pipe management record that has been done by hand writing. The RFID system includes RFID marker, data reader, portable computer operating program, and data base server operating program. In this system, the data is managed with a single communication device, and it would be possible to share the information on the underground facilities and water treatment facilities. This RFID technology is expected to provide water service providers with opportunities to develop more scientific and modernized underground facilities information systems.

This study was conducted to examine the byproducts formation characteristics at the water treatment plants which applying electrolysis as a disinfection process in Gangwondo, Korea. Total of forty plants located in Gangwon Province, Korea were selected for the study. Correlation between dissolved organic carbon(DOC) and SUVA254 was not clear. Among the species of the disinfection byproducts(DBPs), chlorate and trihalomethanes(THMs) accounted for 76% and 14% of DBPs, respectively. The effect of DOC or SUVA254 on DBPs formation was not clearly demonstrated. The increased amount of THMs due to the raw water bromide content was found primarily in the form of chloroform, and the percent fraction of BDCM(bromodichloromethane) and DBCM(Dibromochloromethnae) was relatively insignificant. When the value of SUVA254 was greater than 2 L/mg·m, the percent fraction of BDCM and DBCM decreased while percent fraction of CF(chloroform) increased.

본 연구에서는 발광층의 전자와 정공의 재결합 영역을 확인하고, 단계적 도핑구조를 이용하여 여기자들의 효율적인 분배를 통해 roll-off 효율을 감소시켜서 녹색 인광 유기발광다이오드의 수명 증가 를 나타냈다. 발광층 내 호스트는 양극성의 4,4,N,N'-dicarbazolebiphenyl (CBP)를 사용하여 전하의 이 동을 원활하게 하였다. 발광층을 네 구역으로 분할하여 각각 소자를 제작하였고, 네 구역의 도판트 농도 에 따라 발광효율과 수명 향상을 보였다. 이로써 발광층 내의 단계적 도핑구조를 이용하여 캐리어와 여 기자들이 원활하게 분배된 것을 확인하였다. 기준소자 대비 발광층의 도판트 농도를 5, 7, 11, 9% 순서 로 단계적 도핑구조를 적용한 device C의 수명이 약 73.70% 증가하였고, 휘도 효율은 51.10 cd/A와 외 부 양자 효율은 14.88%의 성능을 보였다.

본 연구에서는 전하 조절층을 이용하여 녹색 인광 유기발광다이오드의 효율의 향상을 나타냈다. 양극성의 4,4,N,N'-dicarbazolebiphenyl (CBP)를 호스트와 전하 조절층으로 사용하여 발광층 내에서 전하의 이동을 원활하게 할 수 있다. 게다가 전하 조절층의 삽입으로 엑시톤을 효과적으로 발광층 내에 제한하여, 삼중항-삼중항 소멸 현상을 억제할 수 있음을 확인하였다. 발광층의 전체 두께는 유지하고, 전하 조절층의 변화를 준 다섯 개의 소자를 제작하여 최적화된 전하 조절층의 두께를 이용한 Device D는 외부 양자 효율 16.22%와 휘도 효율 55.76 cd/A의 성능을 보였다.

유기 박막 트랜지스터 (organic thin-film transistors; OTFTs)는 유기 반도체 그리고 디스플레이와 같은 분야에 그들의 잠재적인 응용 가능성 때문에 많은 주목을 받고 있다. 하지만 급격한 산화 혹은 낮은 전기 이동도와 같은 단점으로 인하여 n-형 물질은 p-형 물질에 비해서 상대적으로 많은 연구가 진행되지 못한 실정이다. 따라서 본 논문에서는 n-형 반도체 물질인 [6,6]-phenyl-C61-butyricacidmethylester (PCBM)과 Poly(4-vinylphenol) (PVP)을 유기 절연막으로 이용하여 o-dichlorobenzene, toluene and chloroform과 같은 다양한 유기 용매를 사용한 플라스틱 기판에 유기트랜지스터를 제작하였고 유기 용매가 ODCB 경우 전계 효과 이동도는 약 0.034 cm2/Vs 그리고 점멸비(on/off ratio)는 ~1.3×105 으로 향상 되었다. 다양한 유기 용매의 휘발성에 따라서 PCBM TFT의 전기적 특성에 미치는 영향을 규명하였다.

Oxide semiconductors Thin-film transistors are an exemplified one owing to its excellent ambient stability and optical transparency. In particular zinc oxide (ZnO) has been reported because It has stability in air, a high electron mobility, transparency and low light sensitivity, compared to any other materials. For this reasons, ZnO TFTs have been studied actively. Furthermore, we expected that would be satisfy the demands of flexible display in new generation. In order to do that, ZnO TFTs must be fabricated that flexible substrate can sustain operating temperature. So, In this paper we have studied low-temperature process of zinc oxide(ZnO) thin-film transistors (TFTs) based on silicon nitride (SiNx)/cross-linked poly-vinylphenol (C-PVP) as gate dielectric. TFTs based on oxide fabricated by Low-temperature process were similar to electrical characteristics in comparison to conventional TFTs. These results were in comparison to device with SiNx/low-temperature C-PVP or SiNx/conventional C-PVP. The ZnO TFTs fabricated by low-temperature process exhibited a field-effect mobility of 0.205 cm2/Vs, a thresholdvoltage of 13.56 V and an on/off ratio of 5.73×106. As a result, We applied experimental for flexible PET substrate and showed that can be used to ZnO TFTs for flexible application.

본 논문은 메탈 이중층 전극을 이용한 유기 박막 트랜지스터를 제작하여 Au나 Ag 금속만으로 제작한 일반적인 유기 박막 트랜지스터와의 전기적 특성을 비교하였다. 전기적 특성에서 게이트 절연층은 높은 K 값을 갖는 Al2O3를 사용하였고, 유기 반도체층은 펜타센을 사용하였다. 본 실험에서 제작한 유기 박막 트랜지스터는 1.6 × 10-1 cm2의 포화영역 이동도를 얻을 수 있었으며, 또한 드레인 전압을 -5V로 하고, 게이트 전압을 3 V에서 -10 V 까지 인가하였을 때 3×105의 전멸 비를 얻을 수 있었다.

본 논문에서는 6,13-bis (triisopropylsily lethynyl)-pentacene (TIPS-pentacene) 유기 박막 트랜지스터에 니켈 버퍼층을 적층했을 때의 효과를 연구하였다. 니켈 (Nickel) / 은(Silver) 소스 드레인 전극은 은 (Silver) 전극이 단독으로 쓰일 때 보다 에너지 레벨차이를 줄여 캐리어의 주입이 더 잘되도록 도와주므로써 전기적 특성을 향상 시켜준다. 또한 유기 게이트 절연체의 추가로 TIPS-pentacene 은 규칙적 배열된 형태를 가지므로써 소자 성능의 향상을 가지고 온다. 제작한 유기박막트랜지스터 에서 0.01 cm2의 포화영역 이동도를 얻을 수 있었으며, 또한 드레인 전압을 50 V로 하고 게이트 전압을 20 V에서 -50 V 까지 인가하였을 때 2×104의 전멸 비를 얻을 수 있었다. 이러한 결과를 polyethylene terephthalate (PET) 기판을 이용한 유연한 OTFTs 에 적용시켜본 결과 유리기판위에 제작했을 때와 비슷한 성능을 얻음을 확인하였다.

본 논문에서는 청색 인광 발광 물질인 bis(3,5-Difluoro-2-(2-pyridyl)phenyl-(2-carboxypyridyl) iridium (III) (Flrpic)과 녹색 인광 발광 물질인 fac-tris(2-phenypyridine) irdium(III) (Ir(ppy)3)와 적색 인광 발광 물질인 his(5-benzoyl-2-phenylpyridinato-C,N)iridium(III) (acetylacetonate) ((Bzppy)2Ir(acac))를 각각 적층하여 백색 유기 발광 다이오드를 제작하였고, 각각의 발광층 사이에 혼합된 스페이서인 4,4'-N,N'-dicarbazole-biphenyl (CBP):4,7-diphenyl-1,10-phenanthroline (BPhen)을 적층하여 그 때의 영향에 대하여 연구하였다. 최적화된 구조에서의 전력 효율은 0.014 mA/cm2에서의 19.7 lm/w를 나타내었으며, 0.127 mA/cm2에서의 11.5%의 외부 양자 효율을 나타내었고, 8 V에서 Commission Internationale do I'Eclairage (CIEx,y) coordinates (x=0.36, y=0.44)의 색좌표를 나타내었다.

본 논문에서는 용액 공정을 이용한 고분자 절연층을 갖는 top-gate 구조의 펜타센 박막 트랜지스터(Thin Film Transistor, TFT)의 특성을 연구하였다. Top-gate 구조의 펜타센 TFT 제작에 앞서 유기 반도체인 펜타센의 결정성 성장을 돕기 위해서 가교된 PVP (cross-linked poly(4-vinylphenol))를 유리 기판 상에 스핀 코팅을 이용하여 형성한 후, 노광 공정을 통해 니켈/은 구조를 갖는 채널 길이 10μm의 소오스, 드레인 전극을 형성하였다. 그리고 열 증착을 이용하여 60 nm 두께의 펜타센 층을 성막하였고, 고분자 절연체로서 PVA(polyvinyl alchol) 또는 가교된 PVA를 용액공정인 스핀 코팅을 이용하여 형성한 후 열 증착으로 알루미늄 게이트 전극을 성막하였다. 이로써 제작된 소자들의 전기적 특성을 확인한 결과 가교된 PVA를 사용한 펜타센 TFT 보다 PVA를 게이트 절연체로 사용한 소자가 전기적 특성이 우수한 것으로 관찰되었다. 이는 PVA의 가교 공정에 의한 펜타센 박막의 성능 퇴화에 기인한 것으로 사료된다. 실험 결과 0.9μm 두께의 PVA 게이트 절연막을 사용한 top-gate 구조의 펜타센 TFT의 전계 효과 이동도와 문턱전압, 그리고 전류 점멸비는 각각, 약 3.9×10-3 cm2/Vs, -11.5 V, 3×105으로써 본 연구에서 제안된 소자가 용액 공정형 top-gate 유기 TFT 소자로서 우수한 성능을 나타냄을 알 수 있었다.

A new blue phosphorescent material for organic light emitting diodes (OLEDs), Iridium(III)bis[2-(4-fIuoro-3-benzonitrile)-pyridinato-N,C2'] picolinate (Firpic-CN), was synthesized and studied. We compared characteristics of Firpic-CN and Bis(3,5-Difluoro-2-(2-pyridyl)phenyl-(2-carboxypyridyl) iridium III (FIrpic) which has been used for blue dopant materials frequently. The devices structure were indium tin oxide (ITO) (1000 a)/N,N'-diphenyl-N,N'-(2-napthyl)-(1,1'-phenyl)-4,4'-diamine (NPB) (500 a)/4,4'-N,N'-dicarbazole-biphyenyl (CBP) : FIrpic and FIrpic-CN (X wt%)/4,7-diphenyl-1,10-phenanthroline (BPhen) (300 a)/lithum quinolate (Liq) (20 a)/Al (1000 a). 15 wt% FIrpic-CN doped device exhibits a luminance of 1450 cd/m2 at 12.4 V, luminous efficiency of 1.31 cd/A at 3.58mA/cm2, and Commission Internationale d'Eclairage (CIEx,y) coordinates of (0.15, 0.12) at 12 V which shows a very deep blue emission. We also measured lifetime of devices and was presented definite difference between devices of FIrpic and FIrpic-CN. Device with FIrpic-CN as a dopant presented lower longevity due to chemical effect of CN ligand.

In this study, we designed color of tunable and high efficient organic materials using the quantum dynamics and the semi-empirical calculation, and applied this results to the fabrication of organic light-emitting diodes. Also we optimized the molecular structure of phosphorescent materials and the energy transfer from a host to a dye which makes organic light-emitting diodes improve. Using quantum dynamics method, the molecular structures of ligand only and the whole metal chelate were optimized, and these energy levels were calculated. From this test results, we could understand the emission mechanism of phosphors with various ligands as well as design the proper ligands reducing the T-T annihilation and the carrier lifetime. We also could design ligands with various colors using this test method.

In this study, hetero-electrode structures have been fabricated to increase luminescence efficiency. The presence of a thin layer of Sn or Ag at the organic-aluminum interface enhanced both electron injection efficiency and electroluminescence when compared to OLEDs using homogeneous electrode. In this paper, the effect of the cathode using Sn/Al hetero electrode structure is observed. Electric properties of the OLED using Sn/Al hetero cathode are improved in comparison of only Al cathode. The hetero-electrode existing different energy level induces the advanced structure of OLED can accumulate electron density. The luminescence efficiency of OLED with Sn/Al of Ag/Al cathode is higher because of their higher electron injection efficiency. And, the turn on voltage of the OLED device using Sn thin layer is lowest as about 10 V.

A new process for polymeric gate insulator in field-effect transistors was proposed. Fourier transform infrared absorption spectra were measured in order to identify ODPA-ODA polyimide. Its breakdown field and electrical conductivity were measured. All-organic thin-film transistors with a stacked-inverted top-contact structure were fabricated to demonstrate that thermally evaporated polyimide films could be used as a gate insulator. As a result, the transistor performances with evaporated polyimide was similar with spin-coated polyimide. It seems that the mass-productive in-situ solution-free processes for all-organic thin-film transistors are possible by using the proposed method without vacuum breaking.