간행물
한국응용과학기술학회지 KCI 등재 The Korean Society of Applied Science and Technology
- 발행기관 한국응용과학기술학회(구 한국유화학회)
- 자료유형 학술지
- 간기 격월간
- ISSN 1225-9098 (Print)2288-1069 (Online)
- 수록기간 1984 ~ 2024
- 주제분류 공학 > 화학공학 공학 분류의 다른 간행물
- 십진분류KDC 575DDC 665
권호리스트/논문검색
Vol.21 No.4 (2004년 12월) 16건
1.
2004.12
구독 인증기관 무료, 개인회원 유료
에멀젼 구조가 변하는 에멀젼 변환은 이미 40년 전에 알려졌다. 에멀젼 변환에서는 O/W 에멀젼이 W/O 에멀젼으로, 또는 이와 반대로 구조가 변하므로 연석상과 분산상이 서로 바뀌게 된다. 그러나 3상 에멀젼에서는 이와 같은 에멀젼 변환뿐만 아니라 어떤 특정한 온도에서 연속상은 변하지 않고 분산상의 구조가 바뀌는 현상이 관찰되었다. 이 현상을 에멀젼이라고 불렀으며 에멀젼 전이가 일어나는 온도를 에멀젼 전이 온도라고 하였다. 에멀젼 전이는 이론적인 고찰의 결과이었으며 양친매성 분자/기름/물의 두 3성분계에 대해서 실험적으로 관찰하였다. 이는 이제까지 보고되지 않았던 새로운 현상이다. 본 논문에서는 에멀젼 전이와 에멀젼 전이를 비교 분석하였다.
4,000원
2.
2004.12
구독 인증기관 무료, 개인회원 유료
In this study, hetero-electrode structures have been fabricated to increase luminescence efficiency. The presence of a thin layer of Sn or Ag at the organic-aluminum interface enhanced both electron injection efficiency and electroluminescence when compared to OLEDs using homogeneous electrode. In this paper, the effect of the cathode using Sn/Al hetero electrode structure is observed. Electric properties of the OLED using Sn/Al hetero cathode are improved in comparison of only Al cathode. The hetero-electrode existing different energy level induces the advanced structure of OLED can accumulate electron density. The luminescence efficiency of OLED with Sn/Al of Ag/Al cathode is higher because of their higher electron injection efficiency. And, the turn on voltage of the OLED device using Sn thin layer is lowest as about 10 V.
4,000원
3.
2004.12
구독 인증기관 무료, 개인회원 유료
Liquid crystal (LC) system was introduced into W/O emulsion in order to enhance the stability and moisturizing effect. The LC system, composed of beeswax, surfactant, and water was formed on the surface of emulsion droplet, which was investigated through a polarized microscope. The phenomenon that the viscosity in W/O emulsion system is decreased with time, was reduced by the formation of LC with the addition of beeswax. Centrifugal separation test showed that the stability of emulsion system was increased with the addition of beeswax to 3%. The color change of vitamin C was delayed in LC emulsion systems, which indicates stabilization effect against the oxidation of vitamin C. Evaporation rate in W/O emulsion was retarded by LC, so that high moisturizing effect is expected in W/O LC system.
4,000원
4.
2004.12
구독 인증기관 무료, 개인회원 유료
Multi-walled carbon nanotubes (CNTs) were prepared by microwave plasma chemical vapor deposition (MPCVD) using various combination of binary catalysts and methane precursor. The maximum yield (10.3 %) of CNTs was obtained using a methane-hydrogen-nitrogen mixture with volume ratio of 1:1:2 at 1000 W of microwave power. As the microwave power increased up to 1000 W, the deposition yield of CNTs raised from 4.1 % to 10. 3 %. However, the prepared CNTs at 800 W showed the more crystalline structure than those prepared at 1000 W. The prepared CNTs over different binary catalysts had various structural conformations such as aligned cylinder, bamboo, and nanofibers. The Id/Ig value of CNTs overFe-Fe/Al2O3, Co-Co/Al2O3, and Co-Cu/Al2O3 were in the range of 0.89~0.93. Among the various binary catalysts used, Fe-Co./Al2O3 showed the highest yield.
4,200원
5.
2004.12
구독 인증기관 무료, 개인회원 유료
High-solid coatings were prepared by blending of previosly synthesized acrylic resins and hexamethylene diisocyanate-trimer and curing it at room temperature. The characterization of the films of the prepared coatings was performed. The impact resistance, cross-hatch adhesion, 60˚specular gloss, and heat resistance of the films proved to be good, and the pencil hardness and drying time proved to be slightly poor. Especially, there was a remarkable improvement in the heat resistance. This improvement may stem from the regular arrangement of ethyl groups introduced into the acrylic resin. As a result of Rigid-body pendulum visco-elasticity measurement, dynamic Tg values of cured films increased with dynamic Tg values.
4,000원
6.
2004.12
구독 인증기관 무료, 개인회원 유료
An acid cleaning agent (AACA) for aluminum was prepared by blending of sorbitol, n-octanoic acid, MJU-100A, Tetronix T-701, PPA-23, C8-83 and phosphoric acid. With the prepared AACA, degreasing, foam height, etching and derusting tests were carried out. As a result, AACA-4 and AACA-7 showed better cleaning ability than commercial acid cleaning agents.
4,000원
7.
2004.12
구독 인증기관 무료, 개인회원 유료
Ethanol washing with distillation as a cleanup process of polycyclic aromatic hydrocarbon(PAH)-contaminated soil was investigated in this study. A multistage ethanol washing with distillation process was applied to three different types of soil, i.e., sandy soil, alluvial soil, and clay with the initial concentration of benzo(a)pyrene 10 mg/kg, benz(a)anthracene 250 mg/kg, and pyrene 100 mg/kg soil. Ethanol was selected as washing solvent because of its high PAH removal efficiency, low cost, and non-toxicity comparing to the other solvent such as isopropyl alcohol and sodium dodecyl sulfate. The satisfactory results (i.e. lower than benzo(a)pyrene 1 mg/kg, pyrene 10 mg/kg, benz(a)anthracene 25 mg/kg, which are the Canada or the Netherlands soil standard) for three types of soils were obtained by at most five-six times washing. It was suggested that organic content in soil decreased the removal efficiency by ethanol washing.
4,000원
8.
2004.12
구독 인증기관 무료, 개인회원 유료
We have extracted the natural pine-needles to use ethanol in solvent, and could obtain the refined oil component from pine-needles extract. We have tested the antimicrobial effect from microbe experiment and analyzed with ICP/OES, GC/MS. we could obtain the next conclusion from the result of this experiment. In the first result of this experiment we could know that in case of increasing concentration of pine-needles, the number of microbe decreased more and more. Also we could know that the refined oil component of pine-needles appeared the sterilization effect of S-aureus and E-coli after 96hrs and 120hrs. So we could know that the refined oil component of appeared effect to microbe. In the second result of this experiment we could know that inorganic materials of Ca, Mg, V, Mn etcs from pine-needles detected to ICP/OES analysis and the aromatic compounds from refined oil component of pine-needles was certificated to GC/MS analysis.
4,000원
9.
2004.12
구독 인증기관 무료, 개인회원 유료
Cysteine-silver complexes were prepared and investigated the antimicrobial activity on rubber mat manufactured with waste rubber. We are exposed to harmful bacteria and fungi all the time. We manufactured antimicrobial mat to be imposed to mats that it can prevent generation of bacteria and microorganisms, and restrict their reproduction. Infection of medical devices causes significant morbidity and mortality. For aim of this study, we measured the antimicrobial mat manufactured with cysteine-Ag complex by CCD, FT-IR and NMR. The effect of mole ratio of cysteine-Ag complex on antimicrobial activity to bacteria and fungi is investigated. Reduction rate is evaluated using the Quinn method. Antimicrobial activity of complex on mole ratio 1:4 was effectively inhibited. The complexes had a better antibacterial activity than antifungal activity on rubber mat.
4,000원
10.
2004.12
구독 인증기관 무료, 개인회원 유료
In this work, the properties as polishing wax for automobile of O/W type microemulsion containing wax, liquid paraffine and quaternaryammonium salt was investigated. The microemulsions were prepared at 96~97℃ by the phase inversion method, and polyoxyethylene(20) sorbitan monooleate (POE(20)SMO) and distearyl dimethyl ammonium chloride(D.D.A.C) as the emulsifiers were used. The mean particle size of the rnicroemulsions was about 7±0.5nm and as the properties of polishing wax, gloss increased degree, water resistant gloss degree, initial and final contact angle after water resistance were tested. The result was that the value of water resistantance and contact angle were decreased with increasing amount of POE(20)SMO and D.D.A.C., while the gloss degree values did not affected. And the rnicroemulsion blended with mono ethylene glycol(MEG) of 5~15wt% showed smaller particle size and more stable particle size distribution than without MEG. Finally, this microemulsion showed more excellent values of gloss degree, the water resistant gloss degree and contact angle, than two kinds of commercial polishing wax for automobile.
4,000원
11.
2004.12
구독 인증기관 무료, 개인회원 유료
Highly ordered pure-silica MCM-41 materials possessing well-defined morphology have been successfully prepared with surfactant used as a template. The fabrication of mesoporous silica has received considerable attention due to the need to develop more efficient materials' for catalysis, separations, and chemical sensing. The surface modified MCM-41 was used as anadsorbent for biomolecules. Silica-supported organic groups and DNA adsorption on surface modified MCM-41 were investigated by FT-IR and UV-Vis spectrometer, respectively. The use of MCM-41 as the modification of electrode surfaces were investigated electrochemical properties of metal mediators with biomolecules. The modified ITO electrodes increased peak currents for a redox process of [Ru(bpy)3]2+ relative to the bare electrode. The electrochemical detection of DNA by cyclic voltammetry when the current is saturated in the presence of the mediator appeared more sensitive due to a higher catalytic current on the MCM-41 supported electrodes modified by carboxylic acid functional groups. The carboxyl or amine groups on the surface of MCM-41 interact and react with the -NH2 groups of guanine and backbone, respectively. Highly ordered mesoporous materials with organic groups could find applications as DNA sensors.
4,000원
12.
2004.12
구독 인증기관 무료, 개인회원 유료
The firing reaction and calcination characteristics of the waste shellfish were examined for the future use as absorbent. The weight variation was measured according to thermal-decomposition using TGA and observed variation of the phase. The qualitative and quantitative analysis of the sample were performed using XRD and the structural analysis, SEM. The results of TGA and XRD experiments showed that the almost all of the raw Corbicula Japonica and Ostrea virginjca were changed from calcite to lime by firing and calcination reaction. The result of SEM experiment showed that the plate type of the raw sample was changed to circle type, so the surface area ratio was increased. Above results suggested that waste shellfish were usable as absorbent in the viewpoint of the reuse of resource and the decrease of environmental pollution.
4,000원
13.
2004.12
구독 인증기관 무료, 개인회원 유료
Reaction conditions and catalysts were investigated for direct CF3I synthesis. Optimum reaction temperature was determined by pyrolysis of CF3H and catalytic reactions. Reactions with changing oxygen concentration were performed. As a result, yield of CF3I increased with decreasing oxygen concentration. Catalytic activity was changed with the weight ratio of the used metal salts. This result was stemmed from the change in the pore size of activated carbon by the metal salts. The optimum reaction conditions were: 600℃, space velocity of 45hr-1, and with 7wt% KF/AC catalyst.
4,000원
14.
2004.12
구독 인증기관 무료, 개인회원 유료
It has been confirmed that some Trihalomethanes (THMs) suspected as carcinogens, can be formed during chlorination for water supply through the reaction of chlorine and humic substances in water. The electrochemical characteristics on activated carbon fiber filter (ACF) electrode were investigated to remove the THMs in the chlorination process of drinking water. The electrochemical removal efficiency depended on the applied voltage and flow rate. In this study, the best result showed that the removal efficiency of THMs was higher than 99%.
4,000원
15.
2004.12
구독 인증기관 무료, 개인회원 유료
Highly crosslinked micron-size monodispersed PMMA/PDVB and PS/PDVB particles were prepared using seeded multi-stage emulsion polymerization. PMMA and PS seed particles were synthesized by seeded multi-stage emulsion polymerization and soap-free emulsion polymerization. Then PMMA/PDVB and PS/PDVB particles were obtained using semi-batch type emulsion polymerized using divinyl benzene as a cross-linkable monomer in the presence of seed particles. PMMA particles with size of ca. 730 nm and polydispersity of 1.03 were successfully prepared in this experiment. PS particles with size of ca. 1.5 μm and polydispersity of 1.01 were prepared in this experiment. Highly crosslinked PS/PDVB particles with size of ca. 1.3 μm and polydispersity of 1.00 were obtained.
4,000원
16.
2004.12
구독 인증기관 무료, 개인회원 유료
The preparation of CaSO4 nanoparticle by vesicles formed spontaneously in cationic OTAC and anionic ADS mixed surfactant solution whose ratio is 0.3/0.7 is investigated. Added electrolytes for preparing nanoparticles reduce vesicle size about 200-300 nm comparing with that of pure vesicle whose size is 700-800 nm by DLS. The core of vesicles has 200 nm size and acts as nanoreactors which same size of monodisperse CaSO4 nanopaticles are formed. Although CaSO4 particles are formed at the outer of vesicles, they are very large and amorphous. The formed particles are identified with XRD analysis after separation due to coinciding with CaSO4 particles.
4,000원
