간행물
한국응용과학기술학회지 KCI 등재 The Korean Society of Applied Science and Technology
- 발행기관 한국응용과학기술학회(구 한국유화학회)
- 자료유형 학술지
- 간기 격월간
- ISSN 1225-9098 (Print)2288-1069 (Online)
- 수록기간 1984 ~ 2024
- 주제분류 공학 > 화학공학 공학 분류의 다른 간행물
- 십진분류KDC 575DDC 665
권호리스트/논문검색
Vol.20 No.1 (2003년 3월) 10건
1.
2003.03
구독 인증기관 무료, 개인회원 유료
In order to prepare a softener, alkyl imidazoline salt, fatty carbamide salt, and fatty polyamide salt were synthesized first, and then the synthesized salts were blended. The prepared softeners were applied to acrylic fibers, and then several properties were tested. As a result, the prepared softeners show good softening and lubricating properties, and they also show a little antistatic property. Through bending resistance tests and measurements of feeling change of acrylic fibers treated with the softeners, it was proved that the prepared softeners are durable softeners.
4,000원
2.
2003.03
구독 인증기관 무료, 개인회원 유료
Environmental friendly acrylics/urea high-solid paints (BEHCU) were prepared through the curing reaction of acrylics resin(BEHC) containing 70wt% of solids content and butylated urea curing agent. BEHC was synthesized by addition copolymerization of caprolactone acrylate(CLA), 2-hydroxypropyl methacrylate(2-HPMA), ethyl methacrylate, and n-butyl acrylate. The addition polymerization of these monomers, especially including flexible CLA monomer and 2-HPMA monomer with OH funtional group, under appropriate reaction conditions resulted in polymers with controlled glass transition temperature(Tg) and crosslinking density. The molecular weight(Mw) of these polymers(BEHCs) was 2940~3240 and polydispersity (Mw/Mn) was in the range of 1.61~1.72. The viscosity and the molecular weight of these acrylic resins increased with increasing Tg. The coated films were prepared using curing reaction between BEHC resin and butylated urea curing agent at 100℃ for 30 minutes. Our experimental resulted showed that enhancement of the coating properties such as adhesion, flexibility, impact resistance, water resistance, and abrasion resistance could be expected through introducing CLA component in acrylic resin for the high-solid content acrylics/urea coatings.
4,300원
3.
2003.03
구독 인증기관 무료, 개인회원 유료
Acidic degreasing agent(AADA) was prepared by blending sorbitol, Newpol PE-68, Na-dioctyl sulfosuccinate, Tetronix T-70l, MJU-100A, n-octanoic acid, and phosphoric acid, The physical properties of AADA tested with aluminum specimen showed the following results ; when 3wt% AADA-5 was performed at 70℃, the degreasing rate was 95% which is comparitively good, and the percentage of etching was 0.277% which was found to be less than that of commercialized product. when 20wt% of AADA-5 was added at 65℃, the percentage of derusting was 91% and the good defoaming effect proved by following low foaming power tests respectively : Ross and Miles, and Ross and Clark methods.
4,000원
4.
2003.03
구독 인증기관 무료, 개인회원 유료
The core-shell latex particles were prepared by sequential emulsion polymerization of alkyl methacrylate and styrene(ST) by using an water-soluble initiator(APS) after preparing monomer pre-emulsion in the presence of an anionic surfactant(SDBS). In organic/organic core-shell polymerization, the pre-emulsion method, which minimized required quantity of sulfactant, has been used to increase the conversion rate and the stability of core-shell latex particles as well as to reduce the formation of secondary particle that cause problems of soap-free emulsion during shell polymerization. We used several methods to observe the core-shell structure. The core-shell structure was studied by measuring pH change during hydrolysis by NaOH, glass transition temperature(Tg) by differential scanning calorimeter(DSC), morphology of latex by transmission electron microscope(TEM) and change of particle size and distribution by a particle analyzer.
4,000원
5.
2003.03
구독 인증기관 무료, 개인회원 유료
LiMn2O4 catalyst for CO2 decomposition was synthesized by oxidation method for 30 min at 600℃ in an electric furnace under air condition using manganese(II) nitrate (Mn(NO3)2·6H2O), Lithium nitrate (LiNO3) and Urea (CO(NH2)2). The synthesized catalyst was reduced by H2 at various temperatures for 3 hr. The reduction degree of the reduced catalysts were measured using the TGA. And then CO2 decomposition rate was measured using the reduced catalysts. Phase-transitions of the catalysts were observed after CO2 decomposition reaction at an optimal decomposition temperature. As the result of X-ray powder diffraction analysis, the synthesized catalyst was confirmed that the catalyst has the spinel structure, and also confirmed that when it was reduced by H2, the phase of LiMn2O4 catalyst was transformed into Li2MnO3 and Li1-2δMn2-δO4-3δ-δ' of tetragonal spinel phase. After CO2 decomposition reaction, it was confirmed that the peak of LiMn2O4 of spinel phase. The optimal reduction temperature of the catalyst with H2 was confirmed to be 450℃(maximum weight-increasing ratio 9.47%) in the case of LiMn2O4 through the TGA analysis. Decomposition rate(%) using the LiMn2O4 catalyst showed the 67%. The crystal structure of the synthesized LiMn2O4 observed with a scanning electron microscope(SEM) shows cubic form. After reduction, LiMn2O4 catalyst became condensed each other to form interface. It was confirmed that after CO2 decomposition, crystal structure of LiMn2O4 catalyst showed that its particle grew up more than that of reduction. Phase-transition by reduction and CO2 decomposition ; Li2MnO3 and Li1-2δMn2-δO4-3δ-δ' of tetragonal spinel phase at the first time of CO2 decomposition appear like the same as the above contents. Phase-transition at 2~5 time ; Li2MnO3 and Li1-2δMn2-δO4-3δ-δ' of tetragonal spinel phase by reduction and LiMn2O4 of spinel phase after CO2 decomposition appear like the same as the first time case. The result of the TGA analysis by catalyst reduction ; The first time, weight of reduced catalyst increased by 9.47%, for 2~5 times, weight of reduced catalyst increased by average 2.3% But, in any time, there is little difference in the decomposition ratio of CO2. That is to say, at the first time, it showed 67% in CO2 decomposition rate and after 5 times reaction of CO2 decomposition, it showed 67% nearly the same as the first time.
4,200원
6.
2003.03
구독 인증기관 무료, 개인회원 유료
We studied on the preparation and evaluation of O/W type microemulsion containing "wax, liquid paraffine and quaternary ammonium salt". And also it was obtained to stability of microemulsions by mono ethylene glycol(MEG) addition. The microemulsions were generally prepared at 96~97℃ by the phase inversion method. We used polyoxyethylene(20) sorbitan monooleate(POE(20)SMO) and distearyl dimethyl ammonium chloride(D.D.A.C.) as the emulsifiers at microemulsion preparation. From the results, we could get best condition for microemulsion preparation, in case of oil phase, montanic ester wax ; 1.1wt%, paraffine wax ; 1.1wt%, liquid paraffine ; 3.1wt%, propylene glycol ; 0.6wt% and ethylene glycol monobutyl ether ; 0.6wt%, when the ratio(wt%) of D.D.A.C. and POE(20)SMO were 2 : 3. And also we could obtained that the distributed particle size of the final microemulsions were about 8±1.5nm and the mean particle size was 7±0.5nm. We got following results from final microemulsions that the percent of transmittance; 96~98% at 700nm. And the microemulsion blended with MEG of 5~15wt% showed smaller particle size and more stable distribution than non-containing MEG.
4,000원
7.
2003.03
구독 인증기관 무료, 개인회원 유료
Garlic extract using super-critical carbon dioxide is influenced by temperature and pressure, and the optimum condition can make under super-critical state. We can know the defects in process of super-critical extration, It can indicate the drop of product rate, energy loss and equipment expense etcs. The minimum inhibition concentration of microbe which garlic extract contains has apperared the concentration more than 800ppm in this experiment. According to the result of this experiment, we can know that the antibiosis effect in the microbe of staphylococcus and fungus has disappeared in the incubation time more than 12 hours.
4,000원
8.
2003.03
구독 인증기관 무료, 개인회원 유료
An intermediate, tetramethylene bis (orthophosphate), was prepared by the esterification of pyrophosphoric acid and l,4-butanediol. Then pyrophosphoric-containing modified polyesters (ATTBs) were synthesized by polycondensation of tetramethylene bis(orthophosphate), trimethylolpropane, adipic acid, and l,4-butanediol. The content of l,4-butanediol was varied from 10 to 20wt% for the reaction. The increase of the amount of l,4-butanediol in the synthesis of ATTBs resulted in increase in average molecular weight and decrease in kinematic viscosity owing to the excellent flowability and reactivity of l,4-butanediol.
4,000원
9.
2003.03
구독 인증기관 무료, 개인회원 유료
Squid ink was added to the low salt fermented squid by 4% of concentration and ripened at 10˚C for 6 weeks and at 20˚C for 28 days. The effect of the squid ink on the non-volatile organic acids of low salt fermented squid were investigated. The results are as follows; The non-volatile organic acid in the salt fermented squid without addition of the squid ink was examined and the result showed that lactic and acetic acids were the major organic acids even if very small amount of citric and oxalic acids were detected. In the squid ink added to the low salt fermented squid, total quantity of non-volatile organic acid in the latter part of the ripening was lower than no treatment groups.
4,000원
10.
2003.03
구독 인증기관 무료, 개인회원 유료
The impregnated activated carbons were prepared by the incipient wetness method with the contents of KIO3 varied from 1.0~10 wt% as the impregnation material. The specific surface area and micropore volume of the rice hulls activated carbon were 2,600~2,800 m2/g and 1.1~1.4 cc/g, respectively. With increasing the contents of impregnation materials, the surface area and micropore volume decreased by 3~21%. However, The amounts of hydrogen sulfide adsorbed increased by 2.1~2.8 times depending on the impregnation content. The optimum contents of KIO3 were 2.4 wt%. Although the breakthrough time and adsorption capacity of hydrogen sulfide decreased with increasing temperature in the case of the unimpregnated activated carbons, they increased by 1.2~ 3.2 times for the case of the impregnated activated carbons. The optimum aspect ratio(L/D) was 1.0 and the adsorption amount of hydrogen sulfide enhanced with increasing the gas flow rate. The regeneration temperature was determined as 400℃ from the TGA experiment. The adsorption capacity of hydrogen sulfide with the impregnated activated carbon decreased gradually as the regeneration continued. The hydrogen sulfide adsorption amount of the regenerated activated carbon up to 4 times was still higher than that of the unimpregnated activated carbon.
4,000원
