This paper analyzed what factors affect increased import from ASEAN agricultural products. This study uses multi-countries gravity model approach with a dataset of agricultural import for the period of 2004 - 2014 and several explanatory variables, and then estimate it using the random-effect panel Tobit. The results revealed that agriculture trade in Korea is influenced by the trade partner’s per capita GDP, population, distance from Korea, FTA preferential taxrate, trade percentage of GDP, agriculture percentage of GDP, the number of immigrants from ASEAN countries, and normal track dummy variables etc. It is found that FTA taxrate affect trade between both partners that can occur loss in agricultural industry. Therefore, applying deliberate standards strategies for normal track selection for future FTA negotiation.

The microstructural properties and electrical characteristics of sputtering films deposited with a Cu-Ga target are analyzed. The Cu-Ga target is prepared using the cold spray process and shows generally uniform composition distributions, as suggested by secondary ion mass spectrometer (SIMS) data. Characteristics of the sputtered Cu-Ga films are investigated at three positions (top, center and bottom) of the Cu-Ga target by X-ray diffraction (XRD), SIMS, 4-point probe and transmission electron microscopy (TEM) analysis methods. The results show that the Cu-Ga films are composed of hexagonal and unknown phases, and they have similar distributions of composition and resistivity at the top, center, and bottom regions of the Cu-Ga target. It demonstrates that these films have uniform properties regardless of the position on the Cu-Ga target. In conclusion, the cold spray process is expected to be a useful method for preparing sputter targets.

PURPOSES: Though the situation that the roundabouts are actively constructed, researches on the effect of the roundabouts focus mainly on the analysis of the expected effects of using only traffic simulation on the operation. Considering such problems, this study is conducted to analyze the effects of the various aspects based on field observation studies. METHODS: This study evaluated and analyzed the effects from the aspects of traffic operation, traffic safety, and traffic behavior by performing field observation studies with six roundabouts with/without signal controls on the pilot project areas for the roundabouts installed in 2010. RESULTS: Through the study results, it was found that the average travel time decreases by 14.7% and 2.4% on the signalized intersections and unsignalized intersections, respectively. The average travel speed increases by 9.7 and 5.8km/h on the roundabouts with/without signal lights. Regarding traffic safety, the speed deviation among individual vehicles decreases by approximately 18.4 to 32.7km/h, thus confirming the safety effects. As the decrease of the number of conflicts, it might be explained that car crashes and collision with pedestrians decreased by 62.2% and 66.7%. Also the result shows that the lowest point of speed in roundabouts appears near the yield line on the entry area on the roundabouts. When passing through the roundabouts, vehicles enter at a speed of 20-30km/h, which is the design speed of the circulatory lane and drive out the roundabout with a higher speed than the entry speed. CONCLUSIONS: When a roundabout is introduced at the intersections below certain traffic volume there are effects of traffic operation, traffic safety, and traffic behavior.

This paper describes the NC simulator system for Wire-cut electrodischarge machining. Electrodischarge Wire-cut machining is applicable to all materials including metals, alloys, and most carbides. Although CAM system generate the NC code considering electrodischarge conditions, incorrect Wire-cut tool path bring about fatal results. The simplest way of simulating a EDM process is to display the trajectory of Wire-cutter location by line segments. With this kind of simulation, the programmer can get a general idea about whether the wire is moving as planned but cannot locate gouging or excess material because only the wire location will be seen, not the changes in the workpiece as it is machined. The ideal way of simulating the EDM process is to display the solid model of the workpiece as it is machined. Therefore we propose the ideal NC simulator system for Wire-cut EDM.

In this paper, we purpose the integrated TMS to solve the problem of current systems. The current system resulted in inconvenience because customers and users must contact to each system, when they want to know the information about orders. In this research, we develope a system with which customers and users can confirm all of order information from one system. To solve this problem, the information brought from two systems is integrated by constructing integrated database.