알루미늄합금 6061-T6 판재에 대하여 마찰교반용접과 텅스텐 이너트 가스 용접의 교차 용접부의 미세조직과 기계적 특성에 있어서 용접 순서의 영향을 분석하기 위한 시험편을 성공적으로 제작하였다. FSW-ED 시험편이 다른 조합들보다 가장 좋은 기계적 특성을 나타내었다. 흥미롭게도, TIG-FSW ED 시험편이 FSW-TIG ED 시험편보다 높은 인장강도를 나타내었다. 용접부 경도의 경우, FSW 시편이 TIG-FSW 및 FSW-TIG 시험편보다 높은 값을 나타내었고, TIG-FSW 시험편이 FSW-TIG 시험편보다 높은 값을 나타내었다. FE-SEM을 이용한 인장 파면에 대한 관찰을 통하여, 모든 시험편에서 연성파괴를 나타내는 다양한 크기의 딤플들이 관찰되었다. FSW-TIG 시험편의 파면에서는 용융지(熔融池) 표면 영역에서 기공들이 관찰되는 반면, TIG-FSW 시험편에서는 기공의 형성은 관찰되지 않았다. 경도와 미세조직의 결과를 통해 TIG-FSW 공정이 FSW-TIG 공정보다 높은 인장강도를 확보할 수 있는 공정임을 확인하였다.

Multiple galvanized steel and aluminium alloy sheets were joined by self-piercing rivet(SPR) and hybrid joining(SPR + adhesive bonding). In this study, tensile-shear load and fatigue properties of multi-layer SPR and hybrid joints were investigated. Moreover, tensile-shear deformation behavior of the joints under different specimen configurations was investigated. Depending on the specimen configurations either top sheet tearing failure mode or rivet tail pull-out failure mode was observed during the tensile-shear tests. The top sheet tearing failure mode resulted in low maximum tensile-shear load, but it led to larger displacement value as compared to that in the tail pull-out failure mode. Maximum tensile-shear load of hybrid joints was about four times higher than that of SPR joints. Also, fatigue limit of hybrid joints was about two times higher than that of SPR joints.

Membrane bioreactors (MBRs) have big issue on high aeration energy. In this study, reciprocation of membrane was adapted to mitigate membrane fouling. Inertial force induced by reciprocation removed foulants from membrane surface. Pilot plant with capacity of 1,100 m³/day was operated for 8 months in Singapore. The result showed stable trans membrane pressure (TMP) and low permeate turbidity below 0.1 NTU at 25 LMH. It also showed 60 times less energy consumption than conventional MBR. Low dissolved oxygen in membrane tank resulted in higher nitrogen removal. Long-term reciprocation requires very strong membrane modules. Braid reinforced membrane and its modules were optimized to reciprocation. The evaluation of them after the operation showed there was no change in all their properties.

In this study, to confirm the effect of alloying elements on the phase transformation and conditions of the friction stir process, we processed two materials, SS400 and SM45C steels, by a friction stir process (FSP) under various conditions. We analyzed the mechanical properties and microstructure of the friction stir processed zone of SS400 and SM45C steels processed under 400RPM - 100mm/min conditions. We detected no macro (tunnel defect) or micro (void, micro crack) defects in the specimens. The grain refinement in the specimens occurred by dynamic recrystallization and stirring. The microstructure at the friction stir processed zone of the SS400 specimen consisted of an α-phase. On the other hand, the microstructure at the friction stir processed zone of the SM45 specimen consisted of an α-phase, Fe3C and martensite due to a high cooling rate and high carbon content. Furthermore, the hardness and impact absorption energy of the friction stir processed zone were higher than those of base metals. The hardness and impact absorption energy of FSPed SM45C were higher than that of FSPed SS400. Our results confirmed the effect of alloying elements on the phase transformation and mechanical properties of the friction stir processed zone.

An ultrafine grained complex aluminum alloy was fabricated by an accumulative roll-bonding (ARB) process using dissimilar aluminum alloys of AA1050 and AA5052 and subsequently annealed. A two-layer stack ARB process was performed up to six cycles without lubricant at an ambient temperature. In the ARB process, the dissimilar aluminum alloys, AA1050 and AA5052, with the same dimensions were stacked on each other after surface treatment, rolled to the thickness reduction of 50%, and then cut in half length by a shearing machine. The same procedure was repeated up to six cycles. A sound complex aluminum alloy sheet was fabricated by the ARB process, and then subsequently annealed for 0.5h at various temperatures ranging from 100 to 350˚C. The tensile strength decreased largely with an increasing annealing temperature, especially at temperatures of 150 to 250˚C. However, above 250˚C it hardly decreased even when the annealing temperature was increased. On the other hand, the total elongation increased greatly above 250˚C. The hardness exhibited inhomogeneous distribution in the thickness direction of the specimens annealed at relatively low temperatures, however it had a homogeneous distribution in specimens annealed at high temperatures.

Polysulfone 재질의 다공성 평판막 및 실관막에 키토산 피막층을 형성시킨 후 반응성 염료인 Cibacron Blue 3GA를 고정화시켜 human serum albumin(HSA)의 결합용량이 최대 70 μg/cm2인 단백질 친화성 막을 제조하였다. 친화성 평판막 모듈을 대상으로 HSA에 대한 용출 크로마토그래피 실험을 수행하여 eluent 용액의 최적 환경조건을 결정하였는바, 1M KCl이 첨가된 농도 0.06 M, pH 10의 universal buffer를 eluent로 사용했을 때 리간드와 결합된 단백질의 용출이 가장 우수하였다. 친화성 평판막 및 실관막 모듈을 대상으로 HSA의 전열 크로마토그래피 실험을 수행하여 단백질에 대한 동적 결합용량을 측정하였다. 이 결과 동적 결합용량은 평판막 모듈의 경우에는 loading 용액의 유량과 HSA의 농도가 증가함에 따라 평형 결합용량 값으로부터 크게 감소하였으나, 실관막 모듈의 경우에는 loading 용액의 유량과 HSA의 농도에 관계없이 항상 평형 결합용량 수준을 유지하였는바, 따라서 실관막 모듈이 평판막 모듈보다 단백질 친화성 크로마토그래피 분리관으로서 더 효과적이었다

The purpose of this study is to understand the structural performance of the specimens beam by changing the depth and width of the U-shaped composite beam. To this end, experimental specimens by changing depth and width as compared with a reference specimen were prepared and tested. As a result of this study, growth of the depth has great effect on the structural performance while a width increase has no significant effect on the structural performance of composite beam.

Background : We are Corporation of Reborn International that studies herbal medicine (Hydroponics Peanut sprout) and natural substance hydroponics. Our work is hydroponically grown peanut sprouts. This introduce, mouse allergic efficacy test and peanut tissue culture were performed. Methods and Results : The peanut sprouts have been widely used for long time of years in many Asian countries. P. sprouts germinated from peanuts, which contain 4 times higher resveratrol compounds than peanuts. The resveratrol have bioactivity effects as anti-inflammatory and anti-cancer. Especially, Our virgin premium peanut sprouts oil (cold pressure; low temperature extraction), natural substance oil produced mainly in peanut sprouts are used for valuable foods and cosmetic that supply essential fatty acids for humans as well as industrial raw functional materials production. In this work, large scale-up production of peanut sprout using hydroponics. Using extracts of peanut sprouts, various efficacy screening, animal test (in vivo, in vitro), and analyzes were also performed. Also, the culturing the peanut callus for increasing the contents of a specific useful ingredient were cultured in modified Murashige-Skoog/MS (sucrose 2%, agar 0.8%, pH 5.7) solid and liquid medium. It was examined that 0, 1, 3, 5, 10 ㎎/ℓ of NAA and 0, 1, 3, 5, 10 ㎎/ℓ of IBA were the callus and shoot induction. It's, developed sample model of food products of various formulations or form of including from peanut sprout extracts. Conclusion : The essential amino acids (composition unsaturated fatty acid) and resveratrol were abound to the extracts. Also, The blood circulation and allergy improvement effect was excellent. And toxicity were not detected in efficacy. Tissue culture screening work, It’s examined that〈 1.0 ㎎/ℓ of NAA and〈 3.0 ㎎/ℓ of IBA were the best composition. However, depending on the purpose of securing the functional material, a more detailed investigation is needed. So, future work is induce roots callus and shoot. The shown results can be applied as sources for functional food, cosmetic, pharmaceuticals, and material.