In order to capture the indoor CO₂ gas from public indoor spaces, a commercial zeolite(4A) was modified with alkali metals useful for adsorption. The prepared sorbents showed somewhat improved adsorption capacity. A few isotherm models were reviewed to characterize the adsorption mechanism of test sorbents. Sips model was found the most appropriate for low level indoor CO₂ adsorption, but revealed a significant error in low pressure regimes and required numerical analysis for quantitative evaluation. Thus, a parameter(qm) in the equation was empirically recorrelated with a operation temperature. As a result, the final model equation including a simple linear function presented less errors for evaluation of the potential capacity of adsorption.

Inconel 718 alloy has excellent mechanical properties at room temperature, high temperature and cryogenic conditions. UTS of base metal is about 900MPa at room temperature; this is increased up to 1300MPa after heat treatment & aging-hardening. Mechanical properties of Inconel 718 Alloy were similar to those shown in the the results for tensile test; mechanical properties of Inconel 718 alloy's GTAW were similar to those of base metal's properties at room temperature. Mechanical properties at cryogenic conditions were better than those at room temperature. Heat-treated Inconel 718, non- filler metal GTAW on Inconel 718 and GTAW used filler metal on Inconel 718's UTS was 1400MPa at cryogenic condition. As a result, the excellent mechanical properties of Inconel 718 alloy under cryogenic conditions was proved through tensile tests under cryogenic conditions. In addition, weldability of Inconel 718 alloy under cryogenic conditions was superior to that of its base-metal. In this case, UTS of hybrid joint (IS-G) at -100˚C was 900MPa. Consequently, UTS of Inconel 718 alloy is estimated to increase from -100˚C to a specific temperature below -100˚C. Therefore, Inconel 718 alloy is considered a pertinent material for the production of Lox Pipe under cryogenic conditions.

The optical characterization of self-assembled InAs/AlAs Quantum Dots(QD) grown by MBE(Molecular Beam Epitaxy) was investigated by using Photoluminescence(PL) spectroscopy. The influence of thin AlAs barrier on QDs were carried out by utilizing a pumping beam that has lower energy than that of the AlAs barrier. This provides the evidence for the tunneling of carriers from the GaAs layer, which results in a strong QD intensity compared to the GaAs at the 16 K PL spectrum. The presence of two QDs signals were found to be associated with the ground-states transitions from QDs with a bimodal size distribution made by the excitation power-dependent PL. From the temperature-dependent PL, the rapid red shift of the peak emission that was related to the QD2 from the increasing temperature was attributed to the coherence between the QDs of bimodal size distribution. A red shift of the PL peak of QDs emission and the reduction of the FWHM(Full Width at Half Maximum) were observed when the annealing temperatures ranged from 500 ˚C to 750 ˚C, which indicates that the interdiffusion between the dots and the capping layer was caused by an improvement in the uniformity size of the QDs.

Many logistics enterprises have made efforts to achieve low costly and high efficient logistics network. The cross-docking system can be a good solution for them. However, it requires tight schedule and all-night operation inevitably for realization of ideal cross-docking. These causes the difficulty of the attainment of daily delivery target and the leave of delivery service persons. In this paper, we develop the line-haul and shuttle service compromised cross-docking model in order to solve the problems practically. We apply the storage process with the cross-docking system and the direct cross-docking between line-haul and shuttle services. The simulation model validates the shorter delivery time by the developed model than the present model.

RFID system the key technology of ubiquitous era, has been emphasized in logistics. Logistic enterprises are required to apply RFID systems considering their investment costs, actual effectiveness, operational satisfaction and so on. For such a purpose, many applicable methods of RFID system have been developed A method that RFID tags are directly attached to products or pallets is utilized in most cases. However, this method requires expensive investment cost, frequent replacement of damaged tags for the small and medium (SM) third party logistics. In this paper, we analyze statistically the current status and requirements of SM third party logistics. Based on their requirements, we propose the realtime warehousing-delivery management by the method to attach a RFID tag to each warehouse rack, together with the economy analysis index in order to evaluate economical efficiency. Consequently, this method is expected to reduce Investment cost and to improve operational effectiveness and satisfaction.

붕산폐액을 함유한 시멘트 및 파라핀 고화체, 폐이온교환수지를 함유한 시멘트 고화체 그리고 잡고체중의 제염지에 대하여 Co-60을 조사선원으로 하여 rads까지 조사하여 발생되는 분해가스의 종류 및 그의 발생량을 분석하였다. 그 결과 분해가스로는 및 등이 발생하였으며, 가 대부분을 차지하였다. 가스발생량은 폐기물과 고화매질의 종류에 따라 으로 상당한 차이를 보였으며, 폐이온교환수지를 함유한 고화체에서 가장 높은 분해가스 발생량을 보였다. 그리고 수소가스는 제염지 폐기물에서 가장 많이 발생하였다. 제염지의 는 0.12이었다.