The initial radionuclide migration quantity depends on the total amount of solubilized species. Geochemical modeling based on a thermodynamic database (TDB) has been employed to assess the solubility of radionuclides. It is necessary to evaluate whether the TDB describes the domestic repository conditions appropriately. An effective way to validate the TDB-based modeling results is through direct comparisons with experimentally measured values under the conditions of interest. Here, the solubilities of trivalent Sm, Eu, and Am were measured in synthetic KURT-DB3 groundwater (Syn- DB3) and compared with modeling results based on ThermoChimie TDB. Ln2(CO3)3·xH2O(cr) (Ln = Sm, Eu) solids were introduced into the Syn-DB3 and dissolved Sm and Eu concentrations were monitored over 223 days. X-ray diffraction analysis confirmed that the crystallinity of the solid compounds was maintained throughout the experiments. The dissolved Sm and Eu concentrations at equilibrium were close to the predicted solubilities of Sm2(CO3)3(s) and Eu2(CO3)3(s) based on the ThermoChimie TDB. The Am solubility measured under oversaturated conditions was comparable to the measured Eu concentrations, although they were measured under different experimental settings. More experimental data are needed for Am-carbonate solid systems with careful characterization of the solid phases to better evaluate Am solubility in domestic groundwater conditions.

Raman characteristics of various minerals constituting natural rocks collected from uranium deposits in Okcheon metamorphic zone in Korea are presented. Micro-Raman spectra were measured using a confocal Raman microscope (Renishaw in Via Basis). The focal length of the spectrometer was 250 mm, and a 1800 lines/mm grating was installed. The outlet of the spectrometer was equipped with a CCD (1,024256 pixel) operating at -70°C. Three objective lenses were installed, and each magnification was 10, 50, and 100 times. The diameter of the laser beam passing through the objective lens and incident on the sample surface was approximately 2 m. The laser beam power at 532 nm was 1.6 mW on the sample surface. Raman signal scattered backward from the sample surface was transmitted to the spectrometer through the same objective lens. To accurately determine the Raman peak position of the sample, a Raman peak at 520.5 cm-1 measured on a silicon wafer was used as a reference position. Since quartz, calcite, and muscovite minerals are widely distributed throughout the rock, it is easy to observe with an optical microscope, so there is no difficulty in measuring the Raman spectrum. However, it is difficult to identify the uraninite scattered in micrometer sizes only with a Raman microscope. In this case, the location of uraninite was first confirmed using SEM-EDS, and then the sample was transferred to the Raman microscope to measure the Raman spectrum. In particular, a qualitative analysis of the oxidation and lattice conditions of natural uraninite was attempted by comparing the Raman properties of a micrometer-sized natural uraninite and a laboratory-synthesized UO2 pellet. Significantly different T2g/2LO Raman intensity ratio was observed in the two samples, which indicates that there are defects in the lattice structure of natural uraninite. In addition, no uranyl mineral phases were observed due to the deterioration of natural uraninite. This result suggests that the uranium deposit is maintained in a reduced state. Rutile is also scattered in micrometer-sizes, similar to uraninite. The Raman spectrum of rutile is similar in shape to that of uraninite, making them confused. The Raman spectral differences between these two minerals were compared in detail.

Plutonium exhibits a variety of oxidation states and has a strong affinity for complexation with organic ligands. Isosaccharinic acid (ISA) is a major degradation product of cellulose materials present in the low to intermediate radioactive wastes. The interaction between trivalent plutonium and ISA can significantly impact the migration and containment of plutonium in the repository environment. In this study, formation of Pu(III) and ISA complexes was investigated at an ionic strength of 1 M of NaClO4 using UV-Vis absorption spectrophotometry. To exclude the effect of the Pu(III) oxidation, absorption spectra were measured within 10 min after adding ISA into Pu(III) solution and processed using HYPSPEC software for deconvolution after baseline correction. Several previous studies showed that the presence of ligands accelerates the oxidation of Pu(III) to Pu(IV). To investigate whether ISA complexation can also accelerate the Pu(III) oxidation, UV-Vis absorption spectra changes over 24 hours were analyzed as a function of the ratio of ISA to plutonium concentration.

Solubility and species distributions of radionuclides in domestic groundwater conditions are required for the safety assessment of deep underground disposal system of spent nuclear fuel (SNF). Minor actinides including Am contribute significant extents to the long-term radiotoxicity of SNF. In this study, the solubility of Am was evaluated in synthetic groundwater (Syn-DB3), which were simulated for the groundwater of the DB3 site in the KAERI Underground Research Tunnel (KURT). Geochemical modeling was performed based on the ThermoChimie_11a (2022) thermochemical database from Andra to estimate the solubility and species distributions of Am in the Syn-DB3 condition. Dissolved Am concentrations in the Syn-DB3 were experimentally measured under oversaturation conditions. Am(III) stock solution in perchlorate media was sequentially diluted in Syn-DB3 to prepare 8 μM Am(III) in Syn-DB3. The pH of the solutions was adjusted to be in the range of 6.4–10.5. A portion of the samples was transferred to quartz cells for UV-Vis absorption and time-resolved laser fluorescence spectroscopy studies and the rest were stored in centrifuge tubes. The absorption spectra of the samples were monitored over 70 days and the results suggest that Am colloidal particles were formed initially in all the samples and precipitated rapidly within two days. Over the experimental period of 236 days, small volume (10 μL) of the samples in the centrifuge tubes were periodically withdrawn after centrifugation (18000 rpm, 1 hr) for the liquid scintillation counting to measure the concentrations of Am dissolved in Syn-DB3. In the end of the experiments, pH of the samples was checked again and the final dissolved Am concentrations were determined after ultrafiltration (10 kDa) to exclude the contribution of colloidal particles. In the pH range of 8-9, which is relevant to the KURT-DB3 groundwater condition, the measured dissolved Am(III) concentrations were converged to around 10-8 M. These values are higher than the solubility of AmCO3OH:0.5H2O(s), but lower than that of AmCO3OH(am). There was no indication of transformation of the amorphous phase to the crystalline phase in our observation time window.

Mobility of radionuclides (RNs) in natural water systems can be increased by complex formation with organic materials. In alkaline cement pore-water conditions, cellulose materials in radwastes such as woods and papers are degraded fast to small organic materials. As a major cellulose degradation product, isosaccharinate (ISA) has been paid attention recently due to its effect on facilitating RNs migration. ISA contains a carboxyl and four hydroxyl functional groups, which cooperatively interact to form chelating bonds with positively charged radionuclides. In our previous study, we determined thermodynamic formation constants, reaction enthalpy and entropy of trivalent americium complexes with ISA, Am(ISA)n (3-n)+ (n=1, 2), in weak acidic condition by conducting temperature-dependent UVVis absorption spectroscopy. Based on those thermodynamic constants along with the experimental results from time-resolved laser induced fluorescence spectroscopy and DFT calculations, we suggested two different chelating-modes of ISA on Am(III). It is more relevant to study Am(III)-ISA complexation under alkaline conditions around pH 12.5, which correspond to the pore-water condition of calciumsilicate- hydrate. Under the alkaline conditions, deprotonated hydroxyl groups of ISA can form more strong interactions with Am. Aquatic hydroxide group can also act as a ligand to form ternary Am(III) -ISA-OH complexes. In this study, absorption spectra of Am-ISA systems were monitored with two variations: first, pH variation (5.5–13) in the presence of constant 30 mM ISA, and second, ISA concentration variation (20 μM – 30 mM) at constant pH of 12.5. As increasing the pH at constant 30 mM ISA, absorption spectra of Am(ISA)2 + were red-shifted from 506.3 to 509.5 nm. The samples showed stable absorption spectra over 30 days. On the other hand, samples with lower ISA concentrations below 10 mM at pH 12.5, showed gradual decrease in the absorbance as sample aging time. By examining filtrates after ultrafiltration (1 kDa), we confirmed that aqueous Am(III)-ISA complexes were formed in the presence of 30 mM ISA at pH 12.5, while colloidal particles and precipitations were formed in the conditions of ISA concentrations lower than 10 mM. In this presentation, we will discuss about probable ternary complex forms of Am(III)-ISA-OH, colloidal forms, and solubility of Am(III) as a function of ISA concentration under alkaline conditions. Absorption and luminescence spectroscopic properties of the Am(III)-ISA-OH ternary system will also be presented.

The bioreduction process from soluble U(VI) to insoluble U(IV) has been extensively studied in the field of radionuclides migration. Since acetic acid (AcOH) is widely used as an electron donor for bioreduction of U(VI), it is necessary to understand the effect of U(VI)-AcOH complexes that exist in different species depending on pH on this process. Changes in samples before and after bioreduction can be compared using time-resolved laser luminescence spectroscopy (TRLLS), which measures the characteristic luminescence spectra of different U(VI) species. Although luminescence properties of U(VI)-AcOH species were reported, experiments were conducted under conditions below pH 4.5. In this study, spectrophotometry and TRLLS for U(VI)-AcOH species (10−100 μM U(VI) and 20 mM AcOH) were performed in pH ranges extending to neutral and alkaline pH regions similar to groundwater conditions as well as acidic pH region. Two different complexes (UO2(AcO)+, UO2(AcO)2 with U(VI) and acetate ratios of 1:1, 1:2) were observed in the acidic pH region. The 1:1 complex, which appears as the pH increases, has no luminescence properties, but its presence can be confirmed because it serves to reduce the luminescence intensity of UO2 2+. In contrast, the 1:2 complex exhibits distinct luminescence properties that distinguish it from UO2 2+. The 1:3 complex (UO2(AcO)3 -) expected to appear with increasing pH was not observed. Two different complexes ((UO2)3(OH)5 +, (UO2)3(OH)7 - with U(VI) and OH ratios of 3:5, 3:7) were observed as the major species in the neutral pH region, but their luminescence lifetimes are remarkably short compared those in the absence of AcOH. Solid U(VI) particles were observed in the alkaline pH region, and they also had completely different luminescence properties from the aforementioned U(VI)-AcOH and U(VI)-hydrolysis species. Based on these results, the effect of pH in the presence of AcOH on the bioreduction process from U(VI) to U(IV) will be discussed.

Dissolution behaviors of ThO2(cr) and PuO2(cr) in synthetic groundwater were investigated at room temperature (23  2°C) under atmospheric conditions. The synthetic groundwater was prepared according to the chemical composition of the KURT-DB3 groundwater. The pH and Eh of the synthetic groundwater were pH 8.9 and 0.5 V, respectively, and the major components were Na, K, Ca, Mg, Si, Cl, SO4, F and HCO3 ions. A few mg of ThO2(cr) and PuO2(cr) powder were added in the synthetic groundwater and the concentrations of Th and Pu in supernatant were monitored for 5 months of reaction time. The concentrations of Th before and after ultracentrifugation were compared, while the solid-liquid phase separation of Pu samples could not be applied due to the small volume of sample solutions. The concentrations of Th and Pu were measured by ICP-MS and alpha spectrometry, respectively. Geochemist’s Work Bench (GWB, standard, 17.0) was applied for the modeling with ThermoChimie TDB v. 11a, which was updated with the latest NEA-TDB (vol. 14). Aqueous species distributions and solubility limiting solid phases of Th and Pu under the synthetic groundwater conditions were evaluated. The results of geochemical modeling indicate that aqueous Th-OH-CO3 ternary species and Pu(IV) species are dominant in solutions equilibrated with ThO2(s) and PuO2(am, hyd), respectively. The dissolution behaviors of ThO2(cr) and PuO2(cr) are comparable to the dissolution of ThO2(aged, logKsp = 8.5) and the oxidative dissolution of PuO2(am, hyd) in the presence of PuO2(coll, hyd), respectively.

The solubility and species distribution of radionuclides in groundwater are essential data for the safety assessment of deep underground spent nuclear fuel (SNF) disposal systems. Americium is a major radionuclide responsible for the long-term radiotoxicity of SNF. In this study, the solubility of americium compounds was evaluated in synthetic groundwater (Syn- DB3), simulating groundwater from the DB3 site of the KAERI Underground Research Tunnel. Geochemical modeling was performed using the ThermoChimie_11a thermochemical database. Concentration of dissolved Am(III) in Syn-DB3 in the pH range of 6.4–10.5 was experimentally measured under over-saturation conditions by liquid scintillation counting over 70 d. The absorption spectra recorded for the same period suggest that Am(III) colloidal particles formed initially followed by rapid precipitation within 2 d. In the pH range of 7.5–10.5, the concentration of dissolved Am(III) converged to approximately 2×10−7 M over 70 d, which is comparable to that of the amorphous AmCO3OH(am) according to the modeling results. As the samples were aged for 70 d, a slow equilibrium process occurred between the solid and solution phases. There was no indication of transformation of the amorphous phase into the crystalline phase during the observation period.

Nuclear spent fuel (SNF) disposal in deep geological repositories is considered as one of sound options for the long-term and safe sequestration of radiotoxic SNF and the sustainable use of nuclear energy. The chemical behaviors of various radionuclides originated from SNF should be well understood to evaluate the migrational behaviors of radionuclides and their reactions and interactions with various geochemical components. Formation of secondary minerals, colloids, other insoluble precipitates is of interest since the concentrations of radionuclides in groundwaters can be limited by the solubility of those solid phases. Particularly when evaluating their solubility, the use of well-defined solid materials in terms of chemical composition and molecular structure is crucial to obtain reliable measurement results. In this study, a synthetic calcium uranyl silicate (Ca-U(VI)-silicate, or uranophane) was prepared and characterized by using various analytical methods including powder X-ray diffraction (pXRD), scanning electron microscopy/energy dispersive X-ray spectrometry (SEM/EDX), and vibrational (FTIR and Raman) spectroscopies. Uranyl silicate minerals are significant to the disposal of nuclear wastes. Our simulation demonstrates that uranophane (Ca[UO2SiO3OH]2·5H2O), one having a U:Si ratio of 1:1, can be a mineral species limiting U(VI) solubility under groundwater conditions in Korea. For the preparation of Ca-U(VI)-silicate, we applied a two-step hydrothermal synthetic procedure reported in literature with modification. Briefly, we conclude that the obtained mineral phase is the ‘α-uranophane’; our characterization results show that the structural and spectroscopic properties of the synthetic Ca-U(VI)-silicate agree well with those of α-uranophane. For instance, the pXRD patterns obtained from the solid show nearly identical diffraction peak positions with those from the reference XRD pattern. From IR and Raman spectroscopy it is noticed that the stretching modes of UO2 2+ and SiO4 4- ions result in strong absorption bands in a region of 700 ~ 1,100 cm-1. Elemental compositions of the synthetic solids were also estimated by using EDX analysis, which results in a Ca:U:Si ratio close to 1:2:2 on average. However, we found that it is difficult to obtain good crystallinity of uranophane, which can be observable by using SEM and its image analysis. We believe that this work serves as a model study to provide synthetic routes of radionuclide-related mineral phases and applicable solid phase characterization methods. In the presentation, the potential use of the U(VI)-silicate solid phase for the upcoming groundwater solubility measurements will be discussed. Keywords: Hexavalent Uranium, Silicate

Complexation of actinides and lanthanides with carboxylic organic ligands is known to facilitate migration of radionuclides from deep geological disposal systems of spent nuclear fuel. In order to examine the ligand-dependent structures of trivalent actinides and lanthanides, a series of Eu(III)-aliphatic dicarboxylate compounds, Eu2(oxalate)3(H2O)6, Eu2(malonate)3(H2O)6, and Eu2(succinate)3(H2O)2, were synthesized and characterized by using X-ray crystallography and time-resolved laser fluorescence spectroscopy. Powder X-ray diffraction results captured the transition of the coordination modes of aliphatic dicarboxylate ligands from side-on to end-on binding as the carbon chain length increases. This transition is illustrated in malonate bindings involving a combination of side-on and end-on modes. Strongly enhanced luminescence of these solid compounds, especially on the hypersensitive peak, indicates a low site symmetry of these solid compounds. Luminescence lifetimes of the compounds were measured to be increased, which is ascribed to the displacement of water molecules in the innersphere of Eu center upon bindings of the organic ligands. The numbers of remaining bound water molecules estimated from the increased luminescence lifetimes were in good agreement with crystal structures. The excitation-emission matrix spectra of these crystalline polymers suggest that oxalate ligands promote the sensitized luminescence of Eu(III), especially in the UV region. In the case of malonate and succinate ligands, charge transfer occurs in the opposite direction from Eu(III) to the ligands under UV excitation, resulting in weaker luminescence.

FTIR (Fourier Transform Infrared) and Raman spectra of KJ-II bentonite provided by Clariant Korea were compared with those of MX-80 bentonite. The FTIR spectra were obtained using a Nicolet 5 FTIR spectrometer (Fisher Scientific) equipped with a diamond ATR (Attenuated Total Reflection) module. The spectra were collected for 64 scans with a resolution of 4 cm−1. Raman spectra were obtained using an optical microscope (Olympus, BX43) and a spectrometer (Andor, SR- 500). The laser beam was focused using an objective lens with a magnifying power of 50. The backscattered light from the sample was collected into an optical fiber with a core diameter of 0.4 mm. The Raman signals were recorded with CCDs (Andor, DV401A-BV for 532 nm laser wavelength and DV420A-OE for 638 and 785 nm laser wavelengths). Each pixel of CCD received the signal for 1 s and its 1000 times accumulated data were collected. The FTIR spectra of the two bentonite samples are very similar. The FTIR spectra of both bentonites showed absorption bands at 3623, 3399, 3231 cm−1 in the higher wavenumber region and at 1637, 1443, 1117, 997, 914, 887, 847, 797, 611, 515, 414 cm−1 in the lower wavenumber region. A sharp band at 3623 cm−1 and the strong band at 997 cm−1 correspond to the OH stretching of structural hydroxyl groups and the Si-O stretching vibration, respectively. In addition to these clear bands, several absorption bands observed in this experiment are well matched with the results reported in various literatures. Unlike the FTIR spectrum, it is not easy to observe the Raman bands of bentonite. The reason is that strong fluorescence interferes with the Raman spectrum. The two bentonite samples showed different fluorescence intensities. In the case of MX-80 bentonite, no clear Raman band was observed due to the influence of very strong fluorescence. KJ-II bentonite showed a relatively weak fluorescence intensity and Raman bands were partially visible at around 147, 260, 397, 709, and 1279 cm−1. In particular, the band at 1279 cm−1 is wide and sturdy. It was observed that the non-powder samples showed a better quality spectra. The Raman characteristics of KJ-II bentonite, which depend on the incident laser wavelength and the sample pretreatment, are discussed in detail.

In the geochemical field, the chemical speciation of hexavalent uranium (U(VI)) has been widely investigated by performing measurements to determine its luminescence properties, namely the excitation, emission, and lifetime. Of these properties, the excitation has been relatively overlooked in most time-resolved laser fluorescence spectroscopy (TRLFS) studies. In this study, TRLFS and continuous-wave excitation–emission matrix spectroscopy are adopted to characterize the excitation properties of U(VI) surface species that interact with amorphous silica. The luminescence spectra of U(VI) measured from a silica suspension and silica sediment showed very similar spectral shapes with similar lifetime values. In contrast, the excitation spectra of U(VI) measured from these samples were significantly different. The results show that distinctive excitation maxima appeared at approximately 220 and 280 nm for the silica suspension and silica sediment, respectively.