국립원예특작과학원에서는 밝은 화색과 안정적인 화형의 생 육이 우수한 빨간색 스탠다드 장미 품종을 육성하기 위해 진한 적색 스탠다드 장미 품종 ‘엔드리스러브(Endless Love)’를 모 본으로, 꽃잎수가 많고 안정적으로 가시가 적은 밝은 노란색 ‘페니레인(Penny Lane)’ 품종을 부본으로 인공교배하였다. 37 개의 교배실생을 양성해 1, 2, 3차에 걸친 특성검정 및 현장실증 을 통해 꽃이 크고 화형이 안정적이며, 재배안정성 및 생산성, 절화특성이 우수한 ‘원교 D1-390’을 최종 선발하였다. 2023년 ‘루비레드(Ruby Red)’로 명명하여 국립종자원에 품종보호출원·등록되었다. ‘루비레드’ 품종은 밝은 적색(R53C)을 가졌으 며, 꽃잎수가 32.8매, 화폭과 화고는 각각 10.9, 5.9cm로 대조 품종보다 크다. 절화장은 평균 71.7cm, 절화수명은 약 16.7일, 수량은 연간 168대/m2로 대조품종인 ‘레드스퀘어(Red Square)’ 대비 절화장이 길고 절화수명도 2배 이상 길며, 수확량도 1.4배 우수하다. 2023년 국내 육성 장미 품종 서울식물원 관람객 대상 공동평가회에서 스탠다드 장미 중 우수한 평가를 받았으며, 현 장 실증 결과 농가별로 균일하고 우수한 수량과 절화품질을 보 였다. 절화용 장미 ‘루비레드’ 품종은 밝은 적색과 우수한 화형 을 가지는 품종으로 해외 대체 품종으로 국내에서 많이 재배될 것으로 기대된다.

Sweetpotato (Ipomoea batatas L.) is a globally important food crop that is susceptible to infestation with the root-knot nematode, Meloidogyne incognita, which causes substantial crop losses. Previous transcriptomic and proteomic analyses identified several genes that displayed differential expression patterns in susceptible and resistant cultivars in response to root-knot nematode (RKN) infection. As a result of previous study, RKN infection was confirmed in the RKN-susceptible sweetpotato cultivar Yulmi. Transcriptome analysis confirmed that among the genes that respond in this process, there are many genes related to ethylene biosynthesis. Therefore, in this study, we focused on the ACC oxidase (ACO) gene, the final enzyme of ethylene biosynthesis, and analyzed the expression patterns under various abiotic stress conditions. Using transcriptome data from our previous study, various expression changes in the four ACO genes used in this study were confirmed during RKN infection. The expression of G25011|TU41034 decreased during RKN infection compared to the untreated control, while the expression of G31097|TU51009, G28360|TU46486, and G15447|TU25395 genes increased in the early stages of RKN infection. Expressions of four ACO genes in leaves of sweetpoato were investigated under abiotic stress conditions such as wounding, high salinity, dehydration, and low temperature stress treatment. Expression of the G25011|TU41034 was significantly increased under abiotic stress conditions except low temperature. G31097|TU51009 was hardly expressed under abiotic stress conditions. Although the expression pattern of G28360|TU46486 and G15447|TU25395 was slightly different depending on the type of abiotic stress, an overall increase in expression was observed. It is expected that this study will be used as basic data on how ethylene biosynthesis responds not only to nematode infection but also to various abiotic stress conditions and will be helpful in functional studies of various crops.

The clearwing moth, Synanthedon bicingulata (Staudinger, 1887), is a pest that infests various species of cherry trees. However, genetic information regarding the genus Synanthedon including S. bicingulata, is limited. In this study, we sequenced a complete mitochondrial genome (mitogenome) of the species. The 16,255 bp of S. bicingulata mitogenome differs from the typical gene arrangement formed in Lepidoptera: trnQ-trnS2-trnM-trnI arrangement between the A+T-rich region and the ND2 junction. Moreover, the genome has untranslated repetitive sequences in the intergenic space between lrRNA and trnV, as well as the CGA start codon in COI and the TTG start codon in ATP8. Similar observations are noted in species belonging to the tribe Synanthedonini within the genus Synanthedon.

Since rice is the main food in Korea, there are no regulations on corn milling yet. Corn is known as one of the world's top three food crops along with wheat and rice, and it is known that 3.5 billion people worldwide use corn for food. In addition, corn mills are not developed or sold in Korea, but the use of corn mills is increasing significantly in many countries in Southeast Asia. In the Philippines, as Korea's rice mill import increases, Korea's KAMICO (Korea Agricultural Machinery Industry Cooperative) and domestic company A agreed to develop a corn mill jointly with PHilMech, an organization affiliated with the Philippine Ministry of Agriculture. However, research on corn milling was very insignificant, so the development was carried out based on the technology of Korea's rice mill. Rice milling is performed by peeling off the skin of rice and producing brown or white rice, so it is carried out by removing the skin and cutting the skin. On the other hand, in the corn mill, the skin of the corn is peeled, pulverized and selected to produce main products suitable for edible use. Therefore, in order to develop a corn mill, processes such as peeling, transfer, grinding, sorting, and by-product separation are required, and suitable parts must be developed. In addition, the performance must be gradually improved through experiments in which corn is repeatedly milled. The Philippines produces 7.98 million tons/year of corn, which is about 100 times that of Korea, and is mostly consumed as a staple food. This is about 10% of the total crop production in the Philippines. In addition, the main cultivation complexes of corn are the mountainous regions of Tarlac or Pangasinan, and the produced corn is 72.4% of the so-called yellow corn called Arabel and Sarangani, and the remaining 27.6% are known as white corn. In this study, it was intended to produce grains of 2.5 mm or less suitable for food for yellow corn and to develop a corn mill for 200 kg per hour. Detailed conditions for development are stipulated as more than 55% of the main product recovery rate, more than 31% of the by-product recovery rate, less than 5% of the raw material loss rate, and more than 80% of the embryo dislocation rate. In this study, to achieve this, the overall process of the corn mill was developed, and the optimal conditions for the corn mill were obtained through the development of parts and empirical tests to improve performance. In addition, it was intended to achieve the development goal by evaluating and analyzing the performance of each part so that it did not conflict.

This study was aimed to isolate bacterial inoculants producing chitinase and evaluate their application effects on corn silage. Four corn silages were collected from four beef cattle farms to serve as the sources of bacterial inoculants. All isolates were tested against Fusarium graminearum head blight fungus MHGNU F132 to confirm their antifungal effects. The enzyme activities (carboxylesterase and chitinase) were also measured to isolate the bacterial inoculant. Based on the activities of anti-head blight fungus, carboxylesterase, and chitinase, L. buchneri L11-1 and L. paracasei L9-3 were subjected to silage production. Corn forage (cv. Gwangpyeongok) was ensiled into a 10 L mini silo (5 kg) in quadruplication for 90 days. A 2 × 2 factorial design consists of F. graminearum contamination at 1.0104 cfu/g (UCT (no contamination) vs. CT (contamination)) and inoculant application at 2.1 × 105 cfu/g (CON (no inoculant) vs. INO (inoculant)) used in this study. After 90 days of ensiling, the contents of CP, NDF, and ADF increased (p<0.05) by F. graminearum contamination, while IVDMD, acetate, and aerobic stability decreased (p<0.05). Meanwhile, aerobic stability decreased (p<0.05) by inoculant application. There were interaction effects (p<0.05) on IVNDFD, NH3-N, LAB, and yeast, which were highest in UCT-INO, UCT-CON, CT-INO, and CT-CON & INO, respectively. In conclusion, this study found that mold contamination could negatively impact silage quality, but isolated inoculants had limited effects on IVNDFD and yeast.

Since high-level radioactive wastes contain long-lived nuclides and emit high energy, they should be disposed of permanently through a deep geological disposal system. In Korea, the first (2016.07) and the second (2021.12) basic plans for the management of high-level disposal systems were proposed to select sites for deep geological disposal facilities and to implement business strategies. Leading countries such as Finland, Sweden and France have developed and applied safety cases to verify the safety of deep geological disposal systems. By examining the regulatory status of foreign leading countries, we analyze the safety cases ranging from the site selection stage of the deep geological disposal system to the securing of the permanent disposal system to the investigation, analysis, evaluation, design, construction, operation, and closure. Based on this analysis, we will develop safety case elements for long-term safety of deep geological disposal systems suitable for domestic situation. To systemically analyze data based on safety cases, we have established a database of deep geological disposal system regulations in leading foreign countries. Artificial intelligence text mining and data visualization techniques are used to provide database in dashboard form rather than simple lists of data items, which is a limitation of existing methods. This allows regulatory developers to understand information more quickly and intuitively and provide a convenient interface so that anyone can easily access the analyzed data and create meaningful information. Furthermore, based on the accumulated bigdata, the artificial intelligence learns and analyzes the information in the database through deep learning, and aims to derive a more accurate safety case. Based on these technologies, this study analyzed the legal systems, regulatory standards, and cases of major international leading countries and international organizations such as the United States, Sweden, Finland, Canada, Switzerland, and the IAEA to establish a database management system. To establish a safety regulation base suitable for the domestic deep geological disposal environment, the database is provided as data to refer to and apply systematic information management on regulatory standards and regulatory cases of overseas leading countries, and it is expected that it will play a key role as a forum for understanding and discussing the level of safety of deep geological disposal system among stakeholders.

In Korea, borated stainless steel (BSS) is used as a storage rack in spent fuel pools (SFP) to maintain the nuclear criticality of spent fuels. As the number of nuclear power plants and the corresponding amount of spent fuels increased, the density in SFP storage rack also increased. In this regard, maintaining subcriticality of spent nuclear fuels became an issue and BSS was selected as the structural material and neutron absorber for high density storage rack. Since it is difficult to replace the storage rack, corrosion resistance and neutron absorbency are required for long period. BSS is based on stainless steel 304 and is specified in the ASTM A887-89 standard depending on the boron concentration from 304B (0.20-0.29% B) to 304B7 (1.75-2.25% B). Due to the low solubility of boron in austenitic stainless steel, metallic borides such as (Fe, Cr) 2B are formed as a secondary phase. Metallic borides could cause Cr depletion near it, which could decrease the corrosion resistance of the material. In this paper, the long-term corrosion behavior of BSS and its oxide microstructures are investigated through accelerated corrosion experiment in simulated SFP conditions. Because the corrosion rate of austenitic stainless steel is known to be dependent on the Arrhenius equation, a function of temperature, the corrosion experiment is conducted by increasing the experimental temperature. Detail microstructural analysis is conducted using a scanning electron microscope, transmission electron microscope and energy dispersive spectrometer. After oxidation, a hematite structure oxide film is formed, and pitting corrosion occurs on the surface of specimens. Most of the pitting corrosion is found at the substrate surface because the corrosion resistance of the substrate, which has low Cr content, is relatively low. Also, the oxidation reaction of B in the secondary phase has the lowest Gibbs free energy compared to other elements. Furthermore, oxidation of Cr has low Gibbs free energy, which means that oxidation of B and Cr could be faster than other elements. Thus, the long-term corrosion might affect the boron content and the neutron absorption ability of the material. Using boron’s high cross-section for neutrons, the neutron absorption performance of BSS was evaluated through neutron transmission tests. The effect of the corrosion behavior of BSS on its neutron absorption performance was investigated. Samples simulated to undergo up to 60 years of degradation before corrosion through accelerated corrosion testing did not show significant changes in the neutron shielding ability before and after corrosion. This can be explained in relation to the corrosion behavior of BSS. Boron was only leached out from the secondary phase exposed on the surface, and this oxidized secondary phase corresponds to about 0.17% of the volume of the total secondary phase. This can be seen as a very small proportion compared to the total boron content and is not expected to have a significant impact on neutron absorption performance.

Kori-1, the nuclear power plants in South Korea, first started operation in April 1978 and was suspended permanently in 2017. The saturation rate time of spent nuclear fuel generated by major nuclear power plants operating in Korea are getting closer. If we fail to dispose spent nuclear fuel, which is equivalent to high-level radioactive waste, the nuclear power plants will have to be shutdown. High-level radioactive waste is permanently disposed through a deep geological disposal system because it contains long-term half-life nuclides and emits high energy. To select the deep geological disposal site and construct the disposal facilities, it is necessary to establish appropriate regulatory policies accordingly. The status of database construction in OECD-NEA, NRC, SITEX, and IAEA, which provides safety regulations for deep geological disposal system, stipulates each requirement for dismantling nuclear power plants. However, details such as specific figures are not specified, and guidelines for the disposal of high-level radioactive wastes are not clearly distinguished. In Korea, the CYPRUS program, an integrated database system, has been developed to support comprehensive performance evaluation for high-level waste disposal. However, due to several difficult situations, maintenance and upgrades have not been performed, so the research results exist only in the form of raw data and the new research results have not been reflected. Other than that, there is no preemptive basis for regulating the deep geological disposal system. With real-time database, we can develop a regulatory system for the domestic deep disposal system by systematically analyzing the regulatory condition and regulatory case data of international organizations and foreign leading countries. The database system processed and stored primary data collected from nuclear safety reports and other related data. In addition, we used relational database and designed table to maximize time and space efficiency. It is provided in the form of a web service so that multiple users can easily find the data they want at the same time. Based on these technologies, this study established a database system by analyzing the legal systems, regulatory standards, and cases of major foreign leading countries such as Sweden, Finland, the United States, and Japan. This database aims to organize data for each safety case component and further prepare a safety regulatory framework for each stage of development of disposal facilities suitable for the domestic environment.

CYPRUS is a web-based waste disposal research comprehensive information management program developed by the Korea Atomic Energy Research Institute over three years from 2004. This program is stored as existing quality assurance documents and data, and the research results can be viewed at any time. In addition, it helps to perform all series of tasks related to the safety evaluation study of the repository in accordance with the quality assurance system. In the future, it is necessary to improve the user convenience by clarifying the relationship between FEP and scenarios and upgrading output functions such as visualization and automatic report generation. This purpose of this study is to research and develop the advanced program of CYPRUS. This study is based on building FEP, DIM and scenario databases. It is necessary to develop an algorithm to analyze and visualize the FEP, DIM and scenario relationship. This project is an integrated information processing platform for DB management and visualization considering user convenience. The first development goal is to build long-term evolutionary FEP, DIM, and scenarios as a database. The linkage by FEP item was designed in consideration of convenience by using a mixed delimiter of letters and numbers. This design provides information on detailed interactions and impacts between FEP items. Scenario data lists a series of events and characteristic change information for performance evaluation in chronological order. In addition, it includes information on FEP occurrence and mutual nutrition by period, and information on whether or not the repository performance is satisfied by item. The second development goal is to realize the relationship analysis and visualization function of FEP and scenario based on network analysis technique. Based on DIM, this function analyzes and visualizes interactions between FEPs in the same way as PID, RES, etc. In addition, this function analyzes FEP and DIM using network analysis technique and visualizes it as a diagram. The developed platform will be used to construct and visualize the FEP DB covering research results in various disposal research fields, to analyze and visualize the relationship between core FEP and scenarios, and finally to construct scenarios and calculation cases that are the evaluation target of the comprehensive performance evaluation model. In addition, it is expected to support the knowledge exchange of experts based on the FEP and scenario integrated information processing platform, and to utilize the platform itself as a part of the knowledge transfer system for knowledge preservation.

In Korea, borated stainless steel (BSS) is used as spent fuel pool (SFP) storage rack to maintain nuclear criticality of spent fuels. As number of nuclear power plants and corresponding number of spent fuels increased, density in SFP storage rack also increased. In this regard, maintain subcriticality of spent nuclear fuels was raised as an issue and BSS was selected as structural material and neutron absorber for high density storage rack. Because it is difficult to replace storage rack, corrosion resistance and neutron absorbency are required for long period. BSS is based on stainless steel 304 and it is specified in the ASTM A887-89 standard depending on the boron concentration from 304B (0.20-0.29% B) to 304B7 (1.75-2.25% B). Due to low solubility of boron in austenitic stainless steel, metallic borides such as (Fe, Cr)2B are formed as secondary phase metallic borides could make Cr depletion near it which could decrease the corrosion resistance of material. In this paper, long-term corrosion behavior of BSS and its oxide microstructures are investigated through accelerated corrosion experiment in simulated SFP condition. Because corrosion rate of austenitic stainless steel is known to be dependent on the Arrhenius equation, a function of temperature, corrosion experiment is conducted by increasing the experimental temperature. Detail microstructural analysis was conducted with scanning electron microscope, transmission electron microscope and energy dispersive spectrometer. After oxidation, hematite structure oxide film is formed and pitting corrosions occur on the surface of specimens. Most of pitting corrosions are found at the substrate surface because corrosion resistance of substrate, which has low Cr content, is relatively low. Also, oxidation reaction of B in the secondary phase has the lowest Gibbs free energy compared to other elements. Furthermore, oxidation of Cr has low Gibbs free energy which means that oxidation of B and Cr could be faster than other elements. Thus, the long-term corrosion might affect to boron content and the neutron absorption ability of the material.

The effect of oxidation time on the characteristics and mechanical properties of spent nuclear fuel cladding was investigated using Raman spectroscopy, tube rupture test, and tensile test. As oxidation time increased, the Raman peak associated with the tetragonal zirconium oxide phase diminished and merged with the Raman peak associated with the monoclinic zirconium oxide phase near 333 cm−1. Additionally, the other tetragonal zirconium oxide phase peak at 380 cm−1 decreased after 100 d of oxidation, whereas the zirconium monoclinic oxide peak became the dominant peak. The oxidation time had no effect on the tube rupture pressure of the oxidized zirconium alloy tube. However, the yield and tensile stresses of the oxidized nuclear fuel cladding tube decreased after 100 d of oxidation. The results of the scanning electron microscopy and transmission electron microscopy were represented with the in-situ Raman analysis result for the oxide characteristics generated on the cladding of spent nuclear fuel.

The establishment of processes for the decommissioning a Nuclear Power Plant (NPP) is one of the objects that must be prepared in carrying out the decommissioning project. In particular, in the domestic situation, where there is no experience of decommissioning commercial NPPs, it is necessary to organize the tasks and contents well in advance for the successful initiation of the project. Therefore, this study intends to present a guide-level approach to develop management for domestic decommissioning projects. As a documented template for recognizing a process, there may be a process map and description, and information such as the work structure and the relations between the activities should be indicated. In reality, activities will be managed through a set of computer system, so it would be better if the work content, activity flow, relation, management target information, computerization contents, etc. were materialized in the process. What is important here is to define the management areas and activities and draw the activity flow. Domestically, it has rich experience in construction of NPPs and has a track record of exporting NPPs to the UAE. From these experiences, we have established a framework for standardized work in construction management and construction processes, and are performing them through a computerized system. Since the work of decommissioning has a similar nature to that of construction, we will be able to benchmark the procedure for the decommissioning from the construction management procedures. Typically, in the case of schedule management, the concept and structure of the construction process will be applicable to the decommissioning. Meanwhile, the licensee of domestic decommissioning is the same as the licensee that performs the operation, and the members who will perform the decommissioning also have experience working in the operation period. Therefore, the decommissioning works are an extension of the task during operation. Representatively, there are some processes that can be applied as it is even when decommissioning, such as dismantling work and the safety management process of the radiation zone. Therefore, in carrying out the decommissioning of NPPs in Korea, processes and activities of the management area should be established from the construction processes with abundant experience and the processes during operation. Rather than making a completely new work process, this approach that properly reflects the existing work flow is expected to be an appropriate way to avoid the repulsion of employees and maladjustment to the new environment.

우리나라 정원의 식물 이용 현황을 알아보고자 전국 36개 정원을 대상으로 정원식물을 조사하였다. 정원은 6가지 유형 으로 구분하였다. 그 결과, 36개소 정원에는 정원식물 712종 류가 식재되고 있었다. 교목, 관목, 초본의 비중은 평균 1:2:7 이었다. 개별 정원(10×10㎡)에서 교목은 평균 2.5종으로 12.6%, 관목은 4.1종 20.7%, 초본은 13.2종 66.7%를 차지했다. 식재 빈도 상위 5%에 40여 종이 포함되었으며, 맥문동, 일본조팝나 무, 수국, 회양목, 단풍나무, 옥잠화, 에키네시아, 산철쭉이 대 표적이었다. 양지형 정원에는 관목이 상대적으로 적고 초본이 많았으며 다른 유형보다 20~40% 이상 다양했다. 그늘형은 초 본보다 교목이 많았으며, 건조형 및 습지형과 마찬가지로 식 재 다양성이 20% 감소했다. 옥상정원의 도시형 정원은 초본 이 전체의 80~90%를 차지하고, 해안형 정원에는 목본과 초본 이 1:1로 목본 중심의 식재 특성을 보였다. 결과적으로 정원 유형에 따라 식재 다양성과 구성 비율이 명확한 차이를 나타 냈다.