This study addresses the environmental impact associated with waste management and natural aggregate production. It explores the potential of utilizing Coal Bottom Ash (CBA) and Reclaimed Asphalt Pavement Aggregate (RAPA) as complete replacements, respectively, for fine and coarse aggregates in concrete. Despite their similarities to natural aggregates, CBA and RAPA often end up in landfills. Laboratory tests were conducted, revealing satisfactory performance in drying shrinkage and air void parameters. However, while the flexural strength met design requirements, the compressive and splitting tensile strengths were lower than predicted. The deviation in strength development behavior from natural aggregate concrete (NAC) was attributed to weak agglomerated aggregates in RAPA and the large size of the interfacial transition zone (ITZ) due to the old asphalt coating surrounding RAPA. To enhance the strength behavior, two methods were employed: compaction in the form of roller-compacted concrete and RAPA abrasion carried out by rolling RAPA in a concrete mixer. Compaction improved aggregate interlock, while RAPA abrasion decreased agglomerated aggregates and minimized asphalt coating, reducing ITZ size. These treatments resulted in improvements in compressive, flexural, and splitting tensile strengths, with the combination of both treatments having the most significant effect. Analysis of relationships between flexural, splitting tensile, and compressive strengths indicated that CBA and RAPA concrete behaved more similarly to NAC after the treatments. This research suggests that with appropriate interventions, it is feasible to utilize CBA and RAPA in concrete, contributing to sustainable construction through improved waste management, carbon footprint reduction, and conservation of natural resources.

Since the decrease of skid resistance of the road surface due to the effects of hydroplaning increases the ratio of vehicle crashes significantly, it is important to predict water film thickness (WFT). Tined is one of the widely used textures for concrete pavements. Since previous WFT models have been developed based on the asphalt pavement texture and broom concrete, it may not give reliable predictions for Water film thickness for tinned concrete. Furthermore, surface flow on tined texture may show hydraulically different characteristics due to the geometric characteristics of tined texture. This study aims to propose a reliable water film thickness prediction model for tined concrete. Three test slabs including a smooth surface, a tined surface with 16mm spacing, and a tined surface with 25mm spacing were prepared. WFTs of the test slab were measured for various conditions such as pavement slope (0-10%), rainfall intensity (0-130mm/h), and drainage path length (0-5m). A statistical model was proposed to predict water film thickness (WFT) as a function of pavement slope, rainfall intensity, drainage path length, and mean texture depth. This model exhibits strong agreement with the experimental test results. The GWNU prediction model consistently provides reliable predictions with the actual WFT for tined concrete pavement. Conversely, the previous equation consistently underestimated the water film thickness, notably on tined surfaces with 16 mm and 25 mm spacing, due to the occurrence of viscous flow along the tined lines.

여름철은 타 계절에 비해 장마와 불안정한 대기 등으로 인하여 빗길 교통사고의 위험성이 크게 증대될 수 있으며, 최근 5년 (2018~2022)간 여름철 빗길 교통사고는 전체 빗길 교통사고의 39%를 차지할 정도로 높은 수준이다. 이러한 빗길 운전은 노면의 배수 불량 및 미끄럼 저항 감소 등으로 인하여 수막현상을 발생시키게 된다. 이에 본 연구에서는 우천 시 도로의 안전성 강화 및 사고 위 험을 최소화하기 위한 요소인 수막두께를 산정하기 위하여 Manning의 평균 유속식을 기반으로 콘크리트 노면의 조도계수 예측 모델을 개발하는 것을 목표로 하였다. 조도계수의 영향인자를 고려하기 위하여 실외 강우 모의 장비를 이용하여 콘크리트를 타설한 뒤 실험 인자로 포장 경사, 배수거리, 강우강도, 노면 조직 특성을 고려하였으며, 이 중 노면 조직 특성은 타이닝 처리를 하지 않은 구간만 고 려한 타 연구의 기존 예측 모델 단점을 보완하기 위하여 16, 25mm 간격의 타이닝 표면 처리한 구간을 추가로 고려하였다. 수막두께 측정은 측정 범위 0.3~5mm의 수막두께 측정 게이지를 제작하여 강우가 모사된 조건에서 배수 거리 1~5m 이내 지점의 노면 조직 상 단과 수면이 접하는 수직 높이를 총 3회 측정하여 평균값을 사용하였다. 실측된 수막두께 데이터베이스를 기반으로 Manning 공식을 이용하여 조도계수를 역산한 결과, 강우강도가 증가함에 따라 조도계수는 감소하였으며, 이는 강우의 증가로 인해 물의 흐름과 콘크리 트 노면 사이의 마찰 저항 감소에 기인한 것으로 판단되었다. 또한 포장 경사가 높고 배수 거리가 짧을수록 배수성이 증가하여 마찰 저항의 지표인 조도계수가 증가하는 것으로 확인되었다. 평균 조직 깊이에 따른 조도계수 영향의 경우, 평균 조직 깊이가 증가할수록 콘크리트 표면에 노출되는 표면적이 증가하여 수막두께가 얕게 생성되고, 얕은 수심으로 인해 물의 흐름 저항이 감소하여 조도계수는 감소하는 것으로 산정되었다. 이후 135개의 데이터를 종합하여 조도계수를 종속변수로 하고 강우강도, 포장경사, 배수거리, 평균 조직 깊이, 수막두께를 독립변수로 하는 회귀분석을 수행하여 조도계수 산정식을 개발하였다.

The strength criteria is the acceptable strength for allowable a vehicle start on a concrete pavement at an early age without causing significant damage. The different agencies have provided the strength criteria based on empirical judgement. To make more comprehensive, the ACI specification provided strength criteria by consideration traffic conditions, slab thicknesses, and slab support based on the concept of damage. However, its neglected to consider the damage caused by curling stress due to temperature gradient in concrete pavement. This research aims to provide a strength criteria for opening traffic on concrete pavements while taking into account the damage caused by curling stress and traffic loading. The tensile stress at critical locations was determine due to curling and traffic loads every hour of early age throughout different seasons. The fatigue damage taken throughout early age was assessed. After this procedure, the strength criteria was established as the evaluated damage that did not exceed an acceptable limit. Accordingly, the strength criteria for opening traffic was determined to ensure that the specified damage level existed subject to the construction season, construction period, traffic type, slab thickness, and slab support of concrete pavement.

PURPOSES : The exposed aggregate concrete pavement (EACP) is adopted to achieve low traffic noise and long-term skid resistance in European countries such as Belgium and Germany. In Korea, it is first introduced at the Myeon Cheon field site in 2010. It reduces 3 dB(A) from tire–pavement noise compared with transverse tining. Recent investigations show that EACP can reduce tire–pavement noise by an additional 5 dB(A) compared with transverse tining. In this study, the tire–pavement interaction noise of EACP is compared with that of conventional pavements such as asphalt pavement, next-generation concrete surfaces (NGCS), and transverse tining. METHODS : EACP is constructed at two field sites on the SOC research center and Yeo-Ju test road to compare the noise level via close proximity noise measurement. In addition, the noise is measured using two vehicle type based on vehicle speeds of 60, 80, and 100 km/h. RESULTS : The results of noise measurement obtained from the SOC research center are as follows: Porous asphalt pavement 92.8 dB(A), HMA 96. dB(A), transverse tining 100.1 dB(A), and 8 mm EACP 97 dB(A) at a driving speed of 80 km/h. For the case of the Yeo-Ju test road. The noise levels at a driving speed of 80 km/h are as follows: 6 mm EACP, 93.6 dB(A); asphalt grooving pavement, 94.72 dB(A); 8 mm EACP, 95.2 dB(A); NGCS, 95.2 dB(A); transverse tining, 104.1 dB(A). CONCLUSIONS : The result of noise measurement of two sites in the SOC research center and test road shows that the noise level of the 6 mm EAC is lower than that of concrete pavement, such as tining and NGCS, and similar to that of asphalt pavement. In addition, the noise level of the 8 mm EAC is similar to that of the NGCS pavement. The noise reduction effect of the EAC is greater when small-sized coarse aggregates with lower flat and elongation ratios are used.

PURPOSES: The main purpose of this study is to develop a high elastic modulus and low-shrinkage roller-compacted concrete base (RCCB) in order to prevent fatigue cracking and reflective cracking in the asphalt surface layer of composite pavement. Using a rigid base material with low shrinkage can be a solution to this problem. Moreover, a strong rigid base with high elastic modulus is able to shift the location of critical tensile strain from the bottom of the asphalt layer to the bottom of the rigid base layer, which can prevent fatigue cracking in the asphalt layer. METHODS: Sensitivity analysis of composite pavement via numerical methods is implemented to determine an appropriate range of elastic modulus of the rigid base that would eliminate fatigue cracking. Various asphalt thicknesses and elastic moduli of the rigid base are used in the analysis to study their respective influences on fatigue cracking. Low-shrinkage RCC mixture, as determined via laboratory testing with various amounts of a CSA expansion agent (0%, 7%, and 10%), is found to achieve an appropriate low-shrinkage level. Shrinkage of RCC is measured according to KS F 2424. RESULTS : This study shows that composite pavements comprising asphalt thicknesses of (h1) 2 in. with E2 > 19 GPa, 4 in. with E2 > 15 GPa, and 6 in. with E2 > 11 GPa are able to eliminate tensile strain in the asphalt layer, which is the cause of fatigue cracking in this layer. Shrinkage test results demonstrate that a 10% CSA RCC mixture can reduce shrinkage by 84% and 93% as compared to conventional RCC and PCC, respectively. CONCLUSIONS: According to the results of numerical analyses using various design inputs, composite pavements are shown to be able to eliminate fatigue cracking in composite pavement. Additionally, an RCC mixture with 10% CSA admixture is able to reduce or eliminate reflective cracking in asphalt surfaces as a result of the significant shrinkage reduction in the RCC base. Thus, this low-shrinkage base material can be used as an alternative solution to distresses in composite pavement.

PURPOSES : The use of roller-compacted concrete pavement (RCCP) is an environmentally friendly method of construction that utilizes the aggregate interlock effect by means of a hydration reaction and roller compacting, demonstrating a superb structural performance with a relatively small unit water content and unit cement content. However, even if an excellent structural performance was secured through a previous study, the verification research on the environmental load and long-term durability was conducted under unsatisfactory conditions. In order to secure longterm durability, the construction of an appropriate internal air-void structure is required. In this study, a method of improving the long-term durability of RCCP will be suggested by analyzing the internal air-void structure and relevant durability of roller-compacted concrete. METHODS: The method of improving the long-term durability involves measurements of the air content, air voids, and air-spacing factor in RCCP that experiences a change in terms of the kind of air-entraining agent and chemical admixture proportions. This test should be conducted on the basis of test criteria such as ASTM C 457, 672, and KS F 2456. RESULTS : Freezing, thawing, and scaling resistance tests of roller compacted concrete without a chemical admixture showed that it was weak. However, as a result of conducting air entraining (AE) with an AE agent, a large amount of air was distributed with a range of 2~3%, and an air void spacing factor ranging from 200 to 300 ㎛ (close to 250 ㎛) coming from PCA was secured. Accordingly, the freezing and thawing resistance was improved, with a relative dynamic elastic modulus of more than 80%, and the scaling resistance was improved under the appropriate AE agent content rate. CONCLUSIONS: The long-term durability of RCCP has a direct relationship with the air-void spacing factor, and it can be secured only by ensuring the air void spacing factor through air entraining with the inclusion of an AE agent.

법무부는 정신장애자 범죄가 점진적으로 증가함에 따라 이들을 전문적으로 치료하고 사회적응능력을 향상시키고 이들의 재범을 방지하기 위해 정신질환 수용자들을 위한 정신보건센터를 2012년 이후 4개의 지방교정청관할하에 개원하였다. 이 연구의 목적은 정신질환수용자들이 정신보건센터에서 치료관련 프로그램, 교육프로그램, 훈련프로그램 등 각종 프로그램이 참가자들의 정신관련 치료와 사회적응능력 향상에 도움이 되는지를 알기 위해 각종 프로그램에 대한 분석이 필요하다. 또한 정신보건센터의 운영방식과 교도소 내의 정신보건센터와 지역보건센터와의 연계방안을 고려해야 할 필요성이 있다. 그리고 정신질환자를 위한 보건센터를 더욱 발전시키기 위해서는 외국주요국의 정신질환수형자에 대한 교정처우는 어떠한지를 살펴본 후 우리의 수형자를 위한 정신보건센터의 발전방안을 모색하고자 한다.

PURPOSES : Recently, bonded concrete overlay has been used as an alternative solution in concrete pavement rehabilitation since its material properties are similar to those of the existing concrete pavements. Deteriorated concrete pavements need rapid rehabilitation in order to prevent traffic jams on Korean expressways. Moreover, speedy and effective repair methods are required. Therefore, the use of bonded concrete overlay with ultra-rapid hardening cement has increased in an effort to reopen promptly the expressways in Korea. However, mobile mixer is required for ultra-rapid hardening cement concrete mixing in the construction site. The use of mobile mixer causes various disadvantages aforementioned such as limitation of the construction supply, open-air storage of mixing materials, increase in construction cost, and etc. In this study, therefore, hydration accelerator in-situ mixing on polymer modified concrete produced in concrete plant is attempted in order to avoid the disadvantages of existing bonded concrete overlay method using ultra-rapid hardening cement. METHODS: Bonded concrete overlay materials using ultra-rapid hardening cement should be meet all the requirements including structural characteristics, compatibility, durability for field application. Therefore, This study aimed to evaluate the application of hydration accelerator in-situ mixing on polymer modified concrete by evaluating structural characteristics, compatibility, durability and economic efficiency for bonded concrete overlay. RESULTS : Test results of structural characteristics showed that the compressive, flexural strength and bond strength were exceed 21MPa, 3.15MPa and 1.4MPa, respectively, which are the target strengths of four hours age for the purpose of prompt traffic reopening. In addition, tests of compatibility, such as drying shrinkage, coefficient of thermal expansion and modulus of elasticity, and durability (chloride ions penetration resistance, freezing-thawing resistance, scaling resistance, abrasion resistance and crack resistance), showed that the hydration accelerator in-situ mixing on polymer modified concrete were satisfied the required criteria. CONCLUSIONS: It was known that the hydration accelerator in-situ mixing on polymer modified concrete overlay method was applicable for bonded concrete overlay and was a good alternative method to substitute the existing bonded concrete overlay method since structural characteristics, compatibility, durability were satisfied the criteria and its economic efficiency was excellent compare to the existing bonded concrete overlay methods.

PURPOSES : The use of environmentally friendly construction methods has been recently encouraged to reduce fuel consumption and the effects of global warming. For this purpose, the roller compacted concrete pavement (RCCP) construction method has been developed. RCCP is more environmentally friendly and economically efficient than general concrete by reducing the amount of CO2 generated through the application of a smaller amount of cement. RCCP has a number of advantages such as an easy construction method, low cost, high structural hydration performance, and aggregate interlocking. However, mix design standards and construction guidelines of RCCP are required for domestic application. In addition, a study on aggregate selection, which has an effect on the characteristics of RCCP, is necessary owing to a limited number of researches. Thus, the aggregate effect on the performance of RCCP in securing the required strength and workability was evaluated in consideration of domestic construction. METHODS : Sand and coarse aggregates of both 19mm and 13mm in maximum size were used in this study. Four types of aggregate gradations (s/a = 30%, 58%, and 70% for the sand and coarse aggregate of 19mm in maximum size, and s/a = 50% for a combination of the three types of aggregates) were set up to investigate the effects of the PCA band on the RCC characteristics. The conditions of s/a = 30% and 70% were evaluated to check the gradation effect outside of the recommended band. The conditions of s/a = 58% and 50% were used because they are the optimum combination of the two and three types of aggregates, respectively. RCCP gradation band was suggested gradation with a proper construction method of RCCP by synthetically comparing and analyzing the correlation of optimum water content, maximum dry density, and strength of requirements through its consistency and compaction test. RESULTS : The lower and upper limit lines are insufficient to secure a relatively strong development and workability compared to an aggregate gradation in the RCCP gradation band region. On the other hand, the line in the RCCP gradation band and the 0.45 power curve in the RCCP gradation band region were satisfactory, ensuring the required strength and workability. CONCLUSIONS: The suitable aggregate gradation on RCCP process should meet the RCCP gradation band area; however, fine particles passing through a #60 sieve do not need to be within the recommended gradation band because the influence of this region on such fine particles is small.

PURPOSES: To ensure appropriate RCC properties with sufficient strength development and workability, it is necessary to secure a proper level of consistency. It is also necessary to secure maximum dry density, which is an important factor for increasing the interaction of aggregate interlocking, leading to an augmentation of RCC strength. On the other hand, the dry density of RCC can be changed owing to the compaction conditions, water content, and particle size distribution. A Proctor test and a modified Proctor test were used for determining the optimum water content needed to achieve maximum dry density with different amounts of compaction energy. A Vebe test, on the other hand, was used for checking the level of consistency, which is important for producing a workable mixture. METHODS : To confirm the degree of compaction at various particle sizes, RCC mixtures with different sand/aggregate ratios were evaluated. The Proctor test and modified Proctor test were applied to these mixtures to check the effect of the aggregate gradation and compaction energy on the maximum dry density and optimum water content. During each test, three specimens were produced for all types of water content under each aggregate gradation. A compaction curve and the optimum water content and maximum dry density for each aggregate gradation were then obtained for both tests. The range of water content for the appropriate consistency of each aggregate gradation was determined through a Vebe test. The optimum water content was then evaluated based on this range. RESULTS : The compaction test results show that the modified Proctor test provides a higher maximum dry density and lower optimum water content compared with the standard Proctor test. For the modified Proctor test, two cases of aggregate gradation (s/a = 30% and 70%) had the optimum water contents outside of the appropriate water content range. For the standard Proctor test, on the other hand, none of aggregate gradations provided the optimum water content within the desired range. CONCLUSIONS : The modified Proctor test should be used for an RCC mixture design because it can provide adequacy between maximum dry density and consistency. Moreover, the compaction roller has become highly developed for higher compaction energy.

More than sixty percent of highways in Korea were constructed with concrete pavement to carry the heavy traffic loads due to the economic development of this country. The service life of some pavements are close to the end, therefore, they requires the maintenances, rehabilitations and reconstructions to improve their structural performances.According to the similarity of material properties to the concrete pavement, bonded concrete overlay isa good rehabilitation technique used steadily in Korea. However, it is recently reported that the bonded concrete overlays in some highways expose the early distresses and it is assumed that the poor bonding is a cause of this problem. Additionally, the poor bonding of bonded concrete overlay is caused by the bond strength that is less than the bond strength criterion. The pre-investigation of various concrete overlays is conducted in laboratory to determine the possible influence factors reducing the bond strength and it indicates that there are two possible factors affecting the bond strength: the concrete overlay types and the substrate conditions. The study investigates the vulnerable factor between the two factors based on theevaluation of the in-situ bond strength data of bonded concrete overlay gathered from some highways in Korea. The bond strength data is collected from two different application areas: the new constructionand the rehabilitation projects. The new construction and the rehabilitation projects used Latex-modified Concrete (LMC) and Ultra-rapid Hardening Latex-modified concrete (URH-LMC), respectively as the concrete overlay. The evaluation of in-situ bond strength is to determine the percentage of unacceptable bond strength in each projectto study the effect of different types of concrete overlay. Moreover, the percentage of bonding failure modes having the bond strengths less than the criterion is also measured to study the effect of substrate condition.As a result, substrate condition is the vulnerable factor affecting the poor bonding and causing the early distresses in bonded concrete overlay.

PURPOSES : Recently, attempts have been made to evaluate tire-pavement noise based on a measure of Mean Profile Depth (MPD). However, equivalent values of MPD appear to correspond to different levels of tire-pavement noise, which indicates that other factors such as texture wavelength need to be included to improve the accuracy of noise prediction. A single index to represent texture wavelength is proposed in this study. A consistent relationship between tire-pavement noise and texture wavelength on asphalt concrete pavement is observed. METHODS: Profile data and tire-pavement noise data were collected from a number of expressway sections in Korea. In addition, texture wavelength was defined by a Peak Number (PN), which was calculated using profile data. Statistical analysis was performed to find the relationship between the PN and tire-pavement noise. RESULTS: As a result of this study, a linear relationship between PN and tire-pavement noise is observed on asphalt concrete pavement. CONCLUSIONS: Tire-pavement noise on asphalt concrete pavement can be predicted from PN information.

PURPOSES: In areas of high traffic volume, such as expressway across large cities, the amount of nitrogen oxides (NOx) emitted into the atmosphere as air pollution can be significant since NOx gases are the major cause of smog and acid rain. Recently, the importance of NOx removal has arisen in the world. Titanium dioxide (TiO2), that is one of photocatalytic reaction material, is very efficient for removing NOx. The NOx removing mechanism of TiO2 is the reaction of solar photocatalysis. Therefore, TiO2 in road structure concrete need to be contacted with ultraviolet rays (UV) to be activated. In general, TiO2 concretes are produced by replacement of TiO2 as a part of concrete binder. However, considerable portion of TiO2 in concrete cannot contact with the pollutant in the air and UV. Therefore, TiO2 penetration method using the surface penetration agents is attempted as an alternative in order to locate TiO2 to the surface of concrete structure. METHODS: This study aimed to evaluate the NOx removal efficiency of photocatalytic concrete due to various TiO2 application method such as mix with TiO2, surface spray(TiO2 penetration method) on hardened concrete and fresh concrete using surface penetration agents. The NOx removal efficiency of TiO2 concrete was confirmed by NOx Analyzing System based on the specification of ISO 22197-1. RESULTS: The NOx removal efficiency of mix with TiO2 increased from 11 to 25% with increasing of replacement ratio from 3 to 7%. In case of surface spray on hardened concrete, the NOx removal efficiency was about 50% due to application amount of TiO2 with surface penetration agents as 300, 500 and 700g/m2. The NOx removal efficiency of surface spray on fresh concrete due to all experimental conditions, on the other hand, which was very low within 10%. CONCLUSIONS: It was known that the TiO2 penetration method as surface spray on hardened concrete was a good alternative in order to remove the NOx gases for concrete road structures.

PURPOSES : This study aimed to evaluate the long-term performance of bonded concrete overlay in Korean Highway, and factors influencing the performances. METHODS: The evaluation for long-term performance of bonded concrete overlay is investigated based on the following study : i) The pavement distress of number of bonded concrete overlay sections in Korean highway are collected through field measurement, and PCI for each section is calculated. ii) Performance of LTPP data of bonded concrete overlay sections in U.S.A is analysed. And it is compared with bonded concrete overlay of Korean highway. iii) An analysis of the factors influencing to long-term performance of bonded concrete overlay is investigated. RESULTS: Performance analysis was confirmed that the overlay thickness was affecting significantly on the Bonded Concrete Overlay life. The comparison of LTPP data(U.S.A) and field measurement data(Korean) was showed. CONCLUSIONS : It was showed that the performance of Korean bonded concrete overlay is relatively lower than that of the bonded concrete overlay in U.S.A. The cause of lower performance can be explained by the lack of overlay thickness.

PURPOSES : About 35% of air pollutant is occurred from road transport. NOx is the primary pollutant. Recently, the importance of NOx removal has arisen in the world. TiO2 is very efficient for removing NOx by photocatalytic reaction. The mechanism of removing NOx is the reaction of photocatalysis and solar energy. Therefore, TiO2 in concrete need to be contacted with solar radiation to be activated. In general, TiO2 concrete are produced by substitute TiO2 as a part of concrete binder. However, 90% of TiO2 in the photocatalysis can not contacted with the pollutant in the air and solar radiation. Coating and penetration method are attempted as the alternative of mixing method in order to locate TiO2 to the surface of structure. METHODS : The goal of this study was to attempt to locate TiO2 to the surface of concrete, so we can use the concrete in pavement construction. The distribution of TiO2 along the depth were confirmed by basing on the comparison of TiO2 compare by using the EDAX(Energy Dispersive X-ray Spectroscopy). RESULTS : TiO2 were distributed within 3mm from concrete surface. This distribution of TiO2 is desirable, since the TiO2 induce photocatalysis are located to where they can be contacted with the air pollutant and solar radiation. CONCLUSIONS : Nano size TiO2 is easily penetration in the top 3mm of concrete surface. By the penetration TiO2 concrete can be produced with the use of only 10% of TiO2, by comparing the mixing types.

PURPOSES : Bonded concrete overlay is a favorable maintenance method since the material properties are similar to existing concrete pavements. In addition, bonded concrete overlay has advantage of structural performance since the overlay layer and the existing pavement perform as a monolithic layer. It is important to have suitable bond strength criteria to secure the performance of bonded concrete overlay. This study aimed to investigate the factors influencing bond strength characteristics between existing concrete pavement and overlay material. METHODS: Bond strength between overlay and existing pavement are measured and analyzed for various conditions such as the type of overlay materials, compressive and flexure strength of overlay and existing pavement, and deterioration status of existing pavement. RESULTS: The strength of overlay material does not significantly influence the bond strength. The overlay of ultra-rapid hardening cement generally gives low bond strength. However, ultra rapid hardening polymer modified concrete gives robust bond strength. The deterioration of existing concrete significantly decrease the bond strength. CONCLUSIONS: Bond strength of bonded concrete overlay highly depends on condition of existing concrete pavement rather than overlay material.

PURPOSES: There is a need to develop a method to incorporate tire-pavement noise in the pavement management system. Tire-pavement noise highly depends on the characteristics of pavement texture. Therefore, estimation of texture characteristics may give useful information to predict tire-pavement noise. This study aimed to find the relationship between tire-pavement noise and MPD(Mean Profile Depth) for concrete pavement. METHODS: MPD and tire-pavement noise were collected on the number of expressway sections including Central Inland Test Road in Korea. Statistical analysis was performed to find the correlationship between MPD and tire-pavement noise. In addition, multiple regression analysis to find the tire-pavement noise based on MPD and type of concrete pavement texture. RESULTS: Linear relationship between MPD and tire-pavement noise is observed for concrete pavement. Furthermore, a forensic equation to estimate tire-pavement noise based on MPD and texture types of concrete pavement is suggested. CONCLUSIONS: Tire-pavement noise on concrete pavement can be predicted based on the consideration of texture type and MPD estimation.

PURPOSES : This study aimed to evaluate the feasibility of AASHTO86 design method for Bonded Concrete Overlay. METHODS : The Feasibility of AASHTO86 design method for Bonded Concrete Overlay is investigated based on the following study : i) Sensitivity analysis of designed service life of Bonded Concrete Overlay by major design input for AASHTO86 guide. ii) Comparison of actual Bonded Concrete Overlay life and predicted Bonded Concrete Overlay life by AASHTO86. iii) Finding the stress component influence the potential distress of Bonded Concrete Overlay based on 3-d FEM analysis. iv) Exploring the limitation of AASHTO86 in the aspect of design input. RESULTS : Sensitivity analysis showed that the condition of existing pavement significantly on the Bonded Concrete Overlay life. Also the overlay thickness affect the Bonded Concrete Overlay life. The comparison of actual Bonded Concrete Overlay life and predicted Bonded Concrete Overlay life showed relatively good agreement when the early distress sections are excluded in comparison. Bonding stress occurred at the interface may be larger than the bond strength used in the specification of Bonded Concrete Overlay construction. CONCLUSIONS : Bonded Concrete Overlay life predicted by the AASHTO86 may not be reliable. Number of points to improve the reliability in the design of Bonded Concrete Overlay are suggested in this study.