DWI 검사 시 인체 조직 및 병변에 근접한 공기는 영상왜곡을 가중해 병변 감별에 어려움을 준다. 이에 본 연구는 팬텀을 제작하 여 기하학적 왜곡을 줄여주는 SMS RESOLVE DWI를 통해 공기 자화율에 의한 왜곡 변화를 정량화하였다. 팬텀은 원통형으로 내부에 공기가 존재하도록 설계하였다. 제한된 환경 속에서 다양한 자화율에 의해 왜곡이 영상에 구현되도록 팬텀 내부에는 증류수, 젤라틴 외 혼합 물질과 공기를 구분되게 채웠다. 팬텀의 정렬을 다르게 하여 공기 있는 상태 실험을 진행 후, 공기 대신 혼합액 넣은 상태 실험을 같은 방식으로 진행하였고 혼합액 대신 증류수 넣은 상태 실험을 진행하였다. 3T MRI 장비로 T2WI, C DWI, SMS-RESOLVE DWI를 촬영하였고 파이썬 OpenCV로 이미지 유사도를 측정 후 비교 분석하였다. 실험 결과 공기 있는 상태 SMS-RESOLVE DWI b0에서 SSIM 평균 0.898, MSE 평균 0.068로 영상왜곡이 가장 적었다. SMS-RESOLVE DWI의 공기 자화율 왜곡 변화는 b0 기준 SSIM, MSE 모두 –0.033~0.003 이미지 유사도 차이를 보였다. SMS-RESOLVE DWI b1000은 수치상 이미지 유사도 차이가 크지 않거나 감쇄되는 때도 있어서 향후 SNR 보완에 초점을 둔다면 보다 개선된 영상진단 성능을 제공할 것으로 기대되고 오픈 소스 라이브러리를 통해 오차를 최소화한 이미지 처리와 유사도를 분석하는 새로운 시도는 앞으로의 연구 방향에 새 모델을 제시한다.

alloy powders were prepared using an industrial scale gas atomizer, followed by warm extrusion. The powders were almost spherical in shape. The microstructure of powders as atomized and bars as extruded was examined as a function of initial powder size distribution using Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectroscope (EDS) and X-ray Diffractometer (XRD). The grain sizes were decreased with extruding as well as decreasing the initial powder sizes. Both the ultimate strength and elongation were enhanced as the initial powder sizes were decreased.

The microstructure and mechanical properties of the alloy prepared by spark plasma sintering of gas atomized powders have been investigated. After consolidation, precipitates were observed to form in the solid solution matrix of the alloy. These precipitates consisted of and phases. The density of the consolidated bulk Mg-Zn-Y alloy was . The ultimate tensile strength and elongation were dependent on the consolidation temperature, which were in the ranges of 280 to 293 MPa and 8.5 to 20.8 %, respectively.

Bulk metallic glass (BMG) composites combining a Cu54Ni6Zr22Ti18 matrix with brass powders or Zr62Al8Ni13Cu17 metallic glass powders were fabricated by spark plasma sintering. The brass powders and Zr-based metallic glass powders added for the enhancement of plasticity are well distributed homogeneously in the Cu-based metallic glass matrix after consolidation. The BMG composites show macroscopic plasticity after yielding, and the plastic strain increased to around 2% without a decrease in strength for the composite material containing 20 vol% Zr-based amorphous powders. The proper combination of strength and plasticity in the BMG composites was obtained by introducing a second phase in the metallic glass matrix.

N-type solid solutions doped with 1 was prepared by melt spinning, crushing and vacuum sintering processes. Microstructure, bending strength and thermoelectric property were investigated as a function of the doping quantity from 0.03wt.% to 0.10wt.% and sintering temperature from to , and finally compared with those of conventionally fabricated alloys. The alloy showed a good structural homogeneity as well as bending strength of . The highest thermoelectric figure of merit was obtained by doping 0.03wt.% and sintering at .