In this study, the safety aspects were studied by comparing the charge control characteristics of the two vehicles when a failure occurs between the OBC including the charging port or the charging door module (CDM) during slow charging using the In Cable Control Box (ICCB) for a long time.When the AC terminal was momentarily disconnected during charging, the Model-3 vehicle was charged normally if the AC circuit was disconnected up to three times, and the charging control was stopped when the number of disconnects reached four times. However, in the Ioniq-5 vehicle, charging control was normally performed when the disconnected AC circuit was normally connected regardless of the number of disconnection.

This research studied faults that may occur during slow charging using the J1772 adapter of Tesla Model-3 electric vehicles. When the AC terminal was instantaneously disconnected, charging was performed normally when an AC circuit with disconnection up to three disconnection times was connected. Charging control was suspended when the number of disconnection reached four times. However, if the AC disconnection time exceeded 22 seconds, the charging control was stopped regardless of the number of disconnection. When a contact failure occurred at the AC terminal, high surge current and noise occurred. However, when the contact improved, the charging control continued. In terms of safety, it seems necessary to take measures such as stopping charging control when detecting noise.

When the CP voltage is disconnected, the measured voltage on the ICCB side is measured to be 12V, and the voltage on the OBC side is measured to be 0V. When the PD signal was disconnected, the ICCB-side measured voltage was 0V and the OBC-side measured voltage was 4.5V. From this, disconnected position be found with the voltage value measured. When CP was disconnected for a short time, the PD voltage did not change to 1.5V, and when the PD was disconnected, the CP signal and PD signal changed to 9V, and if the CP and PD voltages were normal, the charge control could be performed normally.

백령버섯 병재배용 배지 주재료는 콘코브 배지보다는 미루나무톱밥 배지 처리구에서 발이 및 생육특성이 가장 양호하였으며, 배지 영양원으로는 면실피, 면실박, 밀기울, 옥수수분, 미강 등이 적합하였고, 배지 혼합 비율은 58% 이내 범위에서 재료별로 질소함량을 고려하여 가감 사용하는 것이 적당하였으며, T-N 함량이 높은 면실박 사용량은 20% 수준으로 조절할 필요가 있었다. 또한, 배지 첨가제는 탄산칼슘 처리가 소석회 처리보다 양호하였으며, 무처리구의 경우 갓과 대의 탄력성은 감소하고 경도는 증가되는 경향을 보였다. 따라서, 백령버섯 병재배용 최적배지는 미루나무톱밥+면실피+면실박+밀기울+옥수수분+탄산칼슘이 40:20:20:15:3:2의 혼합 비율로 조성되는 처리구였다.

We have analysed the proper motion data of LHS catalog, to derive the faint end of the luminosity function more precise than ever before, by mean absolute method, and by making use of the reudced proper motion diagram. It is found that the relations between the mean absolute magnitude and the reduced proper motion for main sequence stars, subdwarfs, and white dwarfs are so different that the proper application of an appropriate relation to each group is much more important. The derived luminosity function shows the broad maximum peak from M B ∼ 14 to M B ∼ 17 and declines after M B ∼ 17 up to M B ∼ 22 .

The practicality of utilizing chitosan as a natural antimicrobial compound to reduce soybean sprout rot was tested. Domestic and imported soybean seeds were soaked for 6 hours in solutions containing different levels of chitosan and acetic acid (glacial), and cultured at 25~circC for 6 days. In case of domestic seeds, soaking with 1,000ppm chitosan increased germination percentage, hypocotyl thickness, total length, and fresh weight of sprouts by 4%, 5%, 2%, and 1%, respectively. The total sprout yield was increased by chitosan in a concentration-dependent manner in that 1,000ppm chitosan resulted in 8% increment of total yield (7.47kg sprouts/kg seed). Chitosan significantly reduced sprout rot percentage to 7.0% compared to control (13.8%), and consequently enhanced marketable sprout yield by 39%. Compared to domestic seeds, the imported soybean seeds exhibited very low germination percentage regardless of chitosan treatments. Chitosan, nevertheless, consistently induced yield increment and rot decrement in imported soybean sprouts. Although 100ppm acetic acid was effective in reducing sprout rot percentage down to 11.8%, its yield-increasing effects were not as prominent as chitosan. In conclusion, soaking soybean seeds with chitosan seems to be a practical method to enhance the efficiency of soybean sprout production