이 논문에서는 박스형 전력구의 지진응답해석에 사용되는 응답진도법의 보수성을 평가하였다. 이를 위해 25가지 전력구 단면과 각 전력구에 대한 2개의 지반조건을 고려한 총 50개 예제를 선정하였다. 응답진도법의 보수성을 평가하기 위해 동적 지반-구조물 상호 작용을 고려한 정밀해석법에 의한 응답과 비교하였다. 비교결과, 정밀해석 응답에 대한 응답진도법에 의한 응답의 비로 정의한 응답 비의 평균이 1.0에 근접하며, 응답비의 표준편차도 5% 이내로 매우 작아서, 응답진도법에 의한 해석이 정밀해석법과 일관됨을 알 수 있었다. 마지막으로 응답진도법에 의한 응답에 하중계수 1.1을 적용하면 전력구의 보수적인 내진설계가 가능할 것으로 나타났다.

사회기반 시설물의 노후화에 대응해 이상 징후를 파악하고 유지보수를 위한 최적의 의사결정을 내리기 위해선 디지털 기반 SOC 시설물 유지관리 시스템의 개발이 필수적인데, 디지털 SOC 시스템은 장기간 구조물 계측을 위한 IoT 센서 시스템과 축적 데이터 처 리를 위한 클라우드 컴퓨팅 기술을 요구한다. 본 연구에서는 구조물의 다물리량을 장기간 측정할 수 있는 IoT센서와 클라우드 컴퓨팅 을 위한 서버 시스템을 개발하였다. 개발 IoT센서는 총 3축 가속도 및 3채널의 변형률 측정이 가능하고 24비트의 높은 해상도로 정밀 한 데이터 수집을 수행한다. 또한 저전력 LTE-CAT M1 통신을 통해 데이터를 실시간으로 서버에 전송하여 별도의 중계기가 필요 없 는 장점이 있다. 개발된 클라우드 서버는 센서로부터 다물리량 데이터를 수신하고 가속도, 변형률 기반 변위 융합 알고리즘을 내장하 여 센서에서의 연산 없이 고성능 연산을 수행한다. 제안 방법의 검증은 2개소의 실제 교량에서 변위계와의 계측 결과 비교, 장기간 운 영 테스트를 통해 이뤄졌다.

대한민국의 낚시산업은 레저활동을 즐기는 인구 증가로 인해 매년 급성장하고 있으며 이에따라 규모가 큰 9-10톤급 낚시어선 의 수는 매년 늘어나고 있다. 현재 운항 중인 낚시어선은 낚시 활동 중 유류비 절감과 엔진 발생 소음 저감을 위해 엔진을 정지하고 배터리를 이용하여 선박의 필수장비를 운영하고 있다. 하지만 배터리의 방전으로 인한 엔진 시동불량 등으로 인해 해상에서 표류되는 사고가 매년 꾸준히 발생하고 있으며, 이는 대형 인명사고로 이어질 수 있다. 본 연구에서는 낚시어선의 안전확보를 위해 태양광 보조전원 설치를 제안하고, 9-10톤급 선박을 대상으로 선정하였다. 대상선박의 태양광 발전설비 공간 확보 가능성을 확인하였으며, 태양광 발전설비의 적용을 검증하기 위해 조업 중 필요한 필수 부하량을 계산하고 전력분석프로그램을 통해 태양광 발전시스템을 모델링하였다. 모델링 된 태양광 발전시스템에 우리나라의 월별 수평면 평균 일사량을 적용하여 낚시어선의 태양광 보조발전장치 적용에 관한 타당성을 입증하였다.

본 연구에서는 CO2 가스 배출 저감 및 선박 폐열 회수 증대를 목적으로 선박 배기로 버려지는 폐열을 전기로 변환하는 ORC(Organic Rankine Cycle) 발전에 대해 시뮬레이션을 통한 냉매별 효율을 보여주고 있다. 상대적으로 고온인 배기가스의 폐열과 상대적으로 저온인 냉각해수를 이용하여 Aspen HYSYS 11을 이용하여 시뮬레이션을 수행하였다. 해수냉각 ORC 발전시스템의 시뮬레이션 결과, 작동유체 효율은 R717 냉매가 2.86 %로 가장 높았고, 다음 순으로 R152a, R134a, R143a, R125a로 나타났다.

In this study, basic strategies for the decommissioning and site remediation of the Fukushima Daiichi Nuclear Power Station (FDNPS) were investigated. Six scenarios were formulated based on two of the three decommissioning strategies of nuclear power plants defined by the International Atomic Energy Agency (IAEA): immediate dismantling and deferred dismantling. A multicriteria decision analysis was performed to analyze the preferences of the options from the viewpoints of the timeframe to complete decommissioning, the resulting waste, the site usability, and the availability of the radioactive waste disposal route. The same six scenarios were applied to both the FDNPS and the nuclear power plants that ceased operation after a normal plant life cycle for comparison. For the FDNPS, the decommissioning project involved fuel debris retrieval, dismantling, and site remediation. The analysis results suggest that the balance between the amount of waste and the time to achieve the end state may be one of the most critical factors to consider when planning the decommissioning and site remediation of the FDNPS.

A laser scabbling experiment was performed using a high-power fiber laser to investigate the removal rate of the concrete block and the scabbled depth. Concrete specimens with a 28-day compressive strength of 30 MPa were used in this study. Initially, we conducted the scabbling experiment under a stationary laser beam condition to determine the optimum scan speed. The laser interaction time with the concrete surface varied between 3 s and 40 s. The degree of spalling and vitrification on the surface was primarily dependent on the laser interaction time and beam power. Furthermore, thermal images were captured to investigate the spatial and temporal distribution of temperature during the scabbling process. Based on the experimental results, the scan speed at which the optical head moved over the concrete was set to be 300 mm∙min−1 or 600 mm∙min−1 for the 4.8-kW or 6.8-kW laser beam, respectively. The spalling rates and average depth on the concrete blocks were measured to be 87 cm3∙min−1 or 227 cm3∙min−1 and 6.9 mm or 9.8 mm with the 4.8-kW or 6.8-kW laser beams, respectively.

There has been a steady rate of accident in Coal Thermal Power Plants which have relatively higher chance of mortality. However, neither the systematic view of safety management nor the methodology such as safety factors or system requirements are yet to be studied in detail. Therefore, this study aims to propose a methodology to preemptively deal with safety issues and to secure fact focused responsibility in safety. It consists of two main parts. First, the Safety Measurement Index(SMI) with total 50 factors is proposed by analyzing the key factors that contribute to safety accidents based on failure mode and effect analysis (FMEA) and quality function deployment (QFD). To analyze the safety requirements, index presented by major countries and organizations are discussed. Second, main features of intelligent CCTV are studied to determine their relative importance for the framework of Smart Safety Management System (SSMS). Main features are discussed with four technological steps. Also, QFD was held to analyze to analyze how key technologies deal with Quality Measurement Index(QMI). The research results of this study reveal that scientific approaches could be utilized in integrating CCTV technologies into a smart safety management system in the era of Industry 4.0. Moreover, this reasearch provides an specific approach or methodology for dealing with safety management in Coal Thermal Power Plant.

The spatial variation characteristics of seismic motions at the nuclear power plant's site and structures were analyzed using earthquake records obtained at the Fukushima nuclear power plant during the Great East Japan Earthquake. The ground responses amplified as they approached the soil surface from the lower rock surface, and the amplification occurred intensively at about 50 m near the ground. Due to the soil layer's nonlinear characteristics caused by the strong seismic motion, the ground's natural frequency derived from the response spectrum ratio appeared to be smaller than that calculated from the shear wave velocity profile. The spatial variation of the peak ground acceleration at the ground surface of the power plant site showed a significant difference of about 0.6 g at the maximum. As a result of comparing the response spectrums at the basement of the structure with the design response spectrum, there was a large variability by each power plant unit. The difference was more significant in the Fukushima Daiichi site record, which showed larger peak ground acceleration at the surface. The earthquake motions input to the basement of the structure amplified according to the structure's height. The natural frequency obtained from the recorded results was lower than that indicated in the previous research. Also, the floor response spectrum change according to the location at the same height was investigated. The vertical response on the foundation surface showed a significant difference in spectral acceleration depending on the location. The amplified response in the structure showed a different variability depending on the type of structure and the target frequency.

Background: Robot-assisted gait training (RAGT) is an effective method for walking rehabilitation. Additionally, the body weight support (BWS) system reduces muscle fatigue while walking. However, no previous studies have investigated the effects of RAGT with BWS on isokinetic strength of quadriceps and hamstring muscles. Objects: The purpose of this study was to investigate the effects of torque, work, and power on the quadriceps and hamstring muscles during RAGT, using the BWS of three conditions in healthy subjects. The three different BWS conditions were BWS 50%, BWS 20%, and full weight bearing (FWB). Methods: Eleven healthy subjects (7 males and 4 females) participated in this study. The Walkbot_S was used to cause fatigue of the quadriceps and hamstring muscles and the Biodex Systems 4 Pro was used to measure the isokinetic torque, work, and power of them. After RAGT trials of each of the three conditions, the subjects performed isokinetic concentric knee flexion and extension, five at an angular velocity of 60°/s and fifteen at an angular velocity of 180°/s. One-way repeated analysis of variance was used to determine significant differences in all the variables. The least significant difference test was used for post-hoc analysis. Results: On both sides, there were significant differences in peak torque (PT) of knee extension and flexion between the three BWS conditions at an angular velocity of 60°/s and 180°/s conditions. A post-hoc comparison revealed that the PT in the BWS 50% was significantly greater than in the BWS 20% and the FWB and the PT in the BWS 20% was significantly greater than in the FWB. Conclusion: The results of this study suggest that the lower BWS during RAGT seems to lower the isokinetic torque, work, and power of the quadriceps and hamstring muscles because of the muscle fatigue increase.

이 연구의 목적은 8주간의 플라이오메트릭 훈련이 대학 태권도 시범단의 순발력, 동적 평형성 및 관절 위치감각에 미치는 영향을 분석하고자 하였다. 태권도 시범 전공 대학생 20명을 훈련군 10명, 통제군 10명으로 분류한 후 운동군은 주 3회, 60분, 8주간 플라이오메트릭 훈련을 하였다. 측정 변인은 제자 리높이뛰기, 제자리멀리뛰기, 배근력, 동적 평형성 및 관절 위치감각으로 사전 사후 측정하였다. 연구 결과, 제자리높이뛰기와 멀리뛰기 및 배근력에서 유의한 운동의 효과가 있었다(p<.05). 동적 평형성은 후방 바깥 쪽과(p<.01) 후방 안쪽에서(p<.05) 유의한 운동의 효과가 있었다. 관절 위치감각은 왼발 15°와(p<.01) 45°에서는(p<.05) 운동군에서 유의한 효과가 있었다. 이상의 결과 8주간의 플라이오메트릭 훈련은 태권도 시범선수의 순발력과 동적 평형성 및 관절 위치감각에 긍정적인 영향을 미치는 것으로 나타났다.

IMO에서는 선박으로부터 온실가스 감축을 위해 선박의 에너지효율 증진에 관한 논의를 진행하고 있다. 현재, 선박으로부터 발생되는 폐열을 이용한 ORC 발전 시스템을 적용함으로써 선박으로부터 높은 에너지 변환 효율을 기대할 수 있다. 이 기술은 물보다 더 낮은 온도 범위에서 증발하는 프레온 또는 탄화수소 계통의 유기 매체를 작동 유체로 사용한다. 이를 통해 상대적으로 낮은 저온에서 증기 (기체)를 생성 및 동력을 발생시킬 수 있다. 본 연구에서는 유기 랭킨 사이클인 ORC 발전 시스템에서 냉매와 폐열 사이 열·유동해석 (Analysis of Heat flow)을 3D 시뮬레이션 기법을 이용하여 구조물의 내·외부에 흐르는 유체가 온도 변화, 속도 변화, 압력 변화 및 질량 변화를 통해서 구조물에 어떤 영향을 미치는지를 분석하고자 하며, 동 연구는 이 기법을 이용하여 ORC 발전 시스템에서 냉매와 선박 주기 관의 배기가스로부터 일어나는 열교환기의 열전달을 해석하였다.

A heat pump system using wasted heat from thermal effluent to supply the heating energy can reduce energy consumption and emissions of greenhouse gases by greenhouse facilities nearby. The Jeju National University consortium constructed a heat pump system using the thermal effluent from the Jeju thermal power plant of KOMIPO to provide with cool or hot water to greenhouse facilities located 2.5km from the power station. In this paper, the system configuration of the heat pump system was summarized, and the results of operations for demonstration of a heating performance carried out during the winter season in 2018 were investigated. Therefore, if the heating control by supplying thermal effluent to the facility greenhouse, it can contribute to reducing the energy cost and improving quality.

Due to stricter environmental regulations of the International Maritime Organization (IMO), the number of ships fueled by Liquefied Natural Gas (LNG) is rapidly increasing. The International Code of the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk (IGC Code) limits the material of tanks that can store cryogenic substances such as LNG. Among the materials listed in the IGC Code, ASTM A553M-17 has been recently adopted as a material for LNG fuel tank projects because of its excellent mechanical properties at cryogenic temperatures. In shipyards, this material is being used to build tanks through Flux Cored Arc Welding (FCAW). However, there is a problem that magnetization occurs during welding and there is a big difference in welding quality depending on the welding position. In order to overcome this problem, this study intends to conduct basic research to apply laser welding to ASTM A553M-17 material. In Part I, the bead shape according to the welding output was analyzed and in PART II, ​​the penetration phenomenon according to the welding speed was analyzed after Bead on Plate (BOP) test. As a result of analyzing the bead shape according to laser power performed in this study, it was confirmed that the laser power and penetration depth are proportional to some extent. In addition, a range of suitable welding power was proposed for the 6.1mm thickness material performed in this study.

The multi-layered heat source model is a model that can cover most of existing studies and can be defined with a simple formula. Based on the methodology performed in previous studies, the welding heat source was found through experiments and FEM under the welding power conditions of three cases and the parameters of the welding heat source were analyzed according to the welding power. In this study, parameters of fiber laser welding heat source according to welding power were searched through optimization algorithm and finite element analysis, and the correlation was analyzed. It was confirmed that the concentration of the welding heat source in the 1st layer was high regardless of the welding power, and it was confirmed that the concentration of the welding heat source in the 5th layer (last layer) increased as the welding power increased. This reflects the shape of the weld bead that appears during actual fiber laser welding, and it was confirmed that this study represents the actual phenomenon.

이 논문에서는 박스형 전력구의 지진응답해석에 사용되는 응답변위법(Response Displacement Method, RDM)의 보수성을 평가하였다. 이를 위하여 25가지 전력구 단면과 각 전력구에 대한 2개의 지반조건을 고려한 총 50개 예제를 선정하였다. 응답변위법에 의한 해석은 다음과 같은 세 가지 방법을 적용하였다: (1) 단일코사인방법, (2) 이중코사인방법, (3) 부지응답해석법. 그리고 이들 응답변위 법의 보수성을 평가하기 위하여 지반-구조물 상호작용을 고려한 동적해석법으로 구한 응답과 비교하였다. 비교결과, 설계지진력을 결정하는 방법 중에서 부지응답해석법이 가장 변동폭이 작았으며, 이중코사인방법이 가장 보수적인 결과를 보였다. 마지막으로 이중 코사인방법을 적용할 때, 응답변위법에 의한 부재력이 동적해석에 의한 값보다 클 확률이 80% 이상이 되기 위한 지반강성 보정계수 C값으로 기능수행수준에서 0.9, 붕괴방지수준에서 0.7을 추천하였다.

Vertically Aligned Carbon Nanotubes (VACNTs)-coated flexible aluminium (Al) foil is studied as an electrode for supercapacitor applications. VACNTs are grown on Al foil inside thermal Chemical Vapor Deposition (CVD) reactor. 20 nm thick layer of Fe is used as a catalyst while Ar, H2 and C2H2 are used as precursor gases. The effect of growth temperature on the structure of CNTs is studied by varying the temperature of CVD reactor from 550 °C to 625 °C. Better alignment of VACNTs arrays on Al foil is recorded at 600 °C growth temperature in comparison to other processing temperatures. Cyclic voltammetry results shows that VACNTs-coated Al foil has a specific capacitance of ~ 3.01 F/g at a scan rate of 50 mV/s. The direct growth of VACNT array results in better contact with Al foil and thus low ESR values observed in impedance spectroscopy analysis. This leads to a fast charge–discharge cycle as well as a very high value of power density (187.79 kW/ kg) suitable for high power applications. Moreover, wettability study shows that the fabricated VACNT electrode has a contact angle of more than 152° which signifies that it is a superhydrophobic surface and hence shows lower specific capacitance in comparison to reported values for VACNT array. Therefore, it is necessary to develop suitable post-processing strategies to make VACNTs hydrophilic to realize their full potential in supercapacitor applications.

This study classifies the compositional methods of power shoulder jackets from 1980 to the present. It analyzes the relevance of jacket details according to how the power shoulder changes and its compositional methods by era. The research subdivides shoulder compositional techniques into seven, based on shoulder variation, sleeve variation, and the body and sleeve combination. The researcher investigates the frequency and trends of composing shoulders and analyzes details pertaining to the silhouette, jacket length, collar shape, and front closure. The most common method of shoulder composition is an angular shoulder variation. The others are a rounded shoulder variation, puffed sleeve, sleeve variation using pattern incision, raglan and kimono sleeves, and a shoulder variation that expanded the angle and width. The frequency differs slightly for each era. The relationship between shoulder compositional methods and details of power shoulder jackets is statistically significant, showing period-related differences. The homogeneity analysis results reveal that the shoulder composition of power shoulder jackets, the times, and details fall into distinct groups. This analysis shows that the silhouette, length, collar, and front closure of the power shoulder jacket differ depending on the power shoulder’s compositional methods. Moreover, the shape of the power shoulder jacket is distinctly different. One can use this data to help develop the power shoulder jacket design by reflecting the details of shoulder compositional methods and changing trends over time.