In an attempt to find the improvement of the fishing efficiency according to the hull form remodeling for the 3 tuna purse seiner, the Catch-Per-Unit-Effort (CPUE) for that undertaken before (2008) and after (2010) was analyzed. In addition, the CPUE of 6 similar ships operated same period and same fishing ground. As result, it came to verify that the three modified ships had a significant value on the CPUE. An another index for the improvement of fishing efficiency is the rate of reduction of fuel oil consumption for the modified ships. Fuel oil consumption per day in service speed as comparing with the original ships were reduced 2.1%, 4.0% and 5.1% on the modified ship A, B, and C respectively. And each ship’s service speed was increased 1.0 kt, 0.6 kt, and 0.4 kt according to the modified ship A, B, and C in due order. In the conclusion, the remodeling job with newly equipped bulbous bow, lengthened slipway and enlarged rudder area were improved fairly much on fuel oil efficiency, the ship’s speed, and in the end, that led to the improving fishing efficiency. Hence, the remodeling of tuna purse seiner come to improve not only the fishing performance, but contribute to the reduction of operating cost by saving energy for the fisheries industry.

This study describes the result on PV system for evaluating the performance of small fishing boats. Photovoltaic system with 200 watts power generation facilities on the 3-ton fishing boat was carried. Load test was performed on the condition that the work lamps lit during night operations. As a result the performance can be used for more than two hours at 60 watt work lamps. The load test was performed on the condition that fishing vessels are on the cruising condition at sea. The solar power systems have been investigated as a power generation efficiency of about 36.55%. Additional tests show that the power generation efficiency is difficult to expect a maximum of 50% or more.Fuel consumption of fishing boats by installing a solar power system is reduced. Also the PV system is useful for the verification of their availability for fishing vessels as well as the satisfaction of the fishermen. The results for the durability of the photovoltaic device is acceptable, including a solar panel, controller and the performance exhibited no breakage in the harsh marine environment or failure so far. The installed PV system was confirmed that the durability with at least 2 years.

본 연구에서는 해상에서의 저체온증 사망위험을 감소시키기 위해, 배의 길이 20미터 미만의 우리나라 소형어선에 비치하기 적합한 구명뗏목의 성능기준을 제안했다. 우리나라에는 소형어선용 구명뗏목이 사용되고 있지 않으며 관련 성능기준도 없다. 국내외 및 국제표준의 성능기준을 비교하고, 외국산 구명뗏목 및 본 연구로 개발된 가방형 시제품(2·4인승)의 성능 평가결과를 분석했다. 그 결과, 근해어선의 구명뗏목에는 ISO 9650-1 기준을 적용하고, 연안어선의 구명뗏목에는 ISO 9650-2보다 기준을 낮추어 적용하는 것이 적절할 것으로 판단된다.

Fishing efficiency of the squid jigging vessel using the LED and metal halide fishing lamp combination was analyzed to reduce the cost for fishing operation utilizing the fishing light system for high degree of efficiency in the squid jigging fishery (one of the representative coastal and offshore fisheries in Korea). This study aims to improve the nature of existing LED lamps and to develop fan-shaped LED lights having 180W of power and ±45˚ angle of light intensity distribution. The marine experiment for making a comparison of their fishing efficiency was tested by a 9.77 tons fishing vessel from Oct. through Dec. 2012. As a result, experimental fishing vessel showed slightly higher fishing efficiency than the average of metal halide lamp-equipped vessel and 20% energy savings. This means that the combination of LED and metal halide lamps would provide an efficient way to lower energy consumption while maintaining fishing efficiency.

The objective of this study is to estimate the optimal net twine thickness of drift net for yellow croaker. The filed experiments of the fishing performance were conducted with three kinds of drift net with different monofilament diameters (No.3=0.284mm, No.4=0.330mm, No.5=0.370mm) the total eight times in the southwest coastal sea of Korea. And the physical properties tests on the monofilaments of experimental net were carried out to estimated breaking load and softness in dry and wet conditions, respectively. From the results, the No.3 mono. was the strongest break load per unit area in dry and wet conditions. And the softness showed that the No. 3 mono. was the most soft than another experimental monofilaments. The fishing performance was; the No. 3 drift net showed the most catches. Conversely, the catches of No. 4 and No. 5 drift net showed the half on the catches of No. 3 drift net. Consequently, the diameter of monofilament in the drift net for yellow croaker should carefully choose to consider the economic sides such as the amount of catches and the cost of catches.

Decoys for automatic jigging machines, the body part of a squid hook, have been developed in small and existing sizes in consideration of squid food, color blindness, and retinomotor responses and in utilization of pearl pigment, PP of high transparency, and combined mixture. In comparison of the developed silver-white decoy and existing decoys, the optical characteristics were examined, and the fishing performance of small size silver-white squid hooks was assessed in application of 4 fishing boats with the squid automatic jigging machine and metal halide fishing lamp in July, 2012. The luminances of the three squid hook colors-green, dark green and silver-white-increased as the intensity of illumination increased. Among these, the increase of silver-white was particularly distinguished. As to the average contrast of squid hooks, that of silver-white was 10.33, which was the highest, and then green 1.86 and dark green -0.10 in the order. As to the fishing performance of the silver-white hook, that of the 202 Geumyeong-ho and 101Yongjin-ho which caught squids were similar to that of the existing green hook and was relatively low in the case of the Dongbu-ho. However, that of the Haengbok-ho which caught relatively small squids whose average length was 19.9cm and installed silver-white hook in all automatic jigging machines was significantly excellent. In order to enhance the fishing performance of small size silver-white hooks, therefore, it would be effective to install in every automatic jigging machines of fishing boat and to start fishing before July by which small squids are caught.

One of representative Korean fisheries, jigging and angling has 5,700 vessels for squid and hairtail. Hairtail angling is the most typical fishery in Jeju and has an enormous impact on regional economy. However, the price hike in oil and labor costs triggered the necessity of developing a high efficient and energy saving fish luring lamp in recent times. For that reason, this study aimed to analyze the fishing performance of the aircooled LED lamp targeting hairtail angling fishery. The experiment was conducted from September through October in 2009-2011 for a 9.77 ton of fishing vessel setting up 100 lamps. The fishing performance was tested compared with 6 vessels using metal halide lamps in the same waters. As the LED lamp's performance goes up, different lamps were used in 2008 for 80W, 2009 for 120W and 2011 for 180W respectively. The catch and CPUE of the experimental vessel have gradually increased respectively taking the 4th and 6th place in 2009, the 4th and 2nd place in 2010, the 1st and 1st place in 2011 among the 7 vessels. In summary, the LED fishing lamp showed higher fishing performance than comparison groups. It saved 33% of oil consumption and cut down on operating expenses and greenhouse gases emission.

In an attempt to respond to the increase in international oil prices and reduce operating expenses, ship remodeling was carried out on a 740ton class tuna purse seiner. To strengthen the competitiveness of the fisheries industry by improving vessel performance, a bulbous bow was newly equipped. The slipway and rudder area were also lengthened and enlarged with the propeller and main engine remained unchanged. To reduce the hull resistance, a circle type bulbous bow was attached on the hull behind bow thruster and thus the cost for exchanging electrical equipment for bow thruster was reduced. The new rudder area was expanded 15% more than the old one within the extent that the existing mechanical control part and rudder stock were not changed. To prevent fishing net damage and stabilize wake field, slipway was lengthened to the optimal position. All of the new design of remodeling parts went through the model tests in towing tank and CWC. Besides resistance test, all of necessary model test results were delivered for hydrodynamic character for the modified ship. The maneuvering simulation to verify that the remodeled ship satisfies the IMO rules was performed in both zigzag and turning tests. The estimated resistance with new bulbous bow and lengthened stern was reduced by 4.8% in the 2-dimensional analysis and 17.4% in the 3-dimensional analysis in comparison of conventional ship. The average reduction of resistance was estimated about 10%. Maneuvering character of modified hull form was found to satisfy all regulations under IMO. The remodeling of tuna purse seiner can not only improve fishing performance but also contribute to reduction of operating cost by saving energy for the fisheries industry.

As the basic study about improvement of yellow croaker drift gill net fishing implement and development of the fishing system, this study drew problem after synthetically analyzing hauling system of yellow croaker drift gill net used in the coast of Chuja Island and tested several characters and analyzed in hauling process with 5 step net hauler model for improving the problem. The analysis results are as follows. When the angle between axises of drum centers was small, it showed the tendency that hauling time was fast. Hauling time was faster when drum was 5 step rather than 3 step. When drum was 5 step, slippery phenomenon was small and hauling was stable. Tension was larger when drum was 5 step rather than 3 step. When drum was 5 step, the range of change of the maximum and minimum value was small and hauling was stable. When drum was 3 step, there was following formula between hauling time (Ht3) and angle between axises of drum centers (Ag) Ht3 : (7.15Hs-0.81) Ag-0.81, when drum was 5 step there was following formula.Ht5 : (6.45Hs-0.75) Ag0.10, here, Hs is hauling speed. When drum was 3 step and hauling speed was 28cm/sec, tension was T=0.08A83-1.60Ag3-0.49Ag+369.56(r=0.99), when drum was 5 step, tension was, T=-0.01Ag3+1.96Ag2-34.05Ag+414.58 (r-0.99), here, T was tension(g).

In spite of many efforts, in the design of high speed fishing vessel the sea-keeping performance improvement without neglection of resistance-propulsion performance by hull form itself has its limitations. In this paper, the development of sea-keeping improving appendage pitching and trim improver for high speed planing hull on behalf of the hull form of fishing vessel has been introduced. The developed appendage verified its effectiveness in the full scale test and also has been proved the better resistance performance in the model test and full scale test.

본 연구에서는 10톤급(9.77 G/T) 소형 연안어선의 저항성능을 회류수조를 이용한 모형시험을 통하여 조사하고, 저항성능개선을 위한 선형특성과 초기 트림에 대한 영향을 검토하였다. 본 연구를 통하여 다음과 같은 몇가지 결론을 도출할 수 있다. (1) 선미 A.P. 이후 돌출부 길이를 키우는 것은, 트림이 억제되면서 선수부 쇄파 현상이 커질 수 있으나, 선미단에서 빠져나가는 유체의 흐름을 개선시켜 저항성능을 크게 향상시킬 수 있다. (2) 적절한 초기 트림을 줌으로써 저항성능이 크게 개선될 수 있다. (3) 선수부 유체흐름을 개선시키기 위해 챠인의 폭을 줄인 선형보다는 이 폭을 그대로 유지하는 것이 파가 선체의 선측을 타고 올라가는 것을 방지하고 트림을 키워 성능측면에서 유리하게 작용한다.

When a ship is course-keeping in the open seas, autopilot system is adapted. The design of autopilot system is very important for improvement of ship′s element research. Automatic steering system consists of autopilot device, power unit, steering gear, magnetic or gyro compass and ship dynamics. In order to evaluate automatic steering system of ships in open seas. we need to know the characteristics of each component of the system, and also to know the characteristics of disturbance to ship dynamics. In this paper, I provide evaluation method of autopilot navigation system of the fishing ship. Prediction method based on the principle of linear superposition is introduced for irregular disturbance. For the evaluation of automatic steering system of a ship, "performance index" is introduced from the viewpoint of energy saving and calculation method is frequency response analysis. Finally, I carried out calculation of sensitivity of control constants of autopilot with various conditions of ocean environments.

TPI는 고속 활주선의 소음, 진동, 트림 및 핏칭운동을 감소시킨 것으로 실선 시운전에서 증명되었다. 또한 모형시험에서 저항성능도 미소하게나마 개선시킨 것으로 입증되었다

이상에서와 같이 LCG위치에 따른 일련의 실험으로부터 다음과 같은 결론을 도출하였다. 1. 선형개발에 있어서 최적선형을 선정하고 이에 대한 성능검증의 일부로써 최적의 LCG위치를 찾는 것은 일반배치의 고려 및 실선에서의 운항 경제성 결정에 중요한 역할을 하며, 이와 같은 연구자료를 데이터 베이스화 함으로써 앞으로의 선형개발에 있어서 유용하게 쓰이게 될 것이다. 2. 저항시험 결과로부터 선미방향으로 LCG위치를 2% 포인트씩 이동하게 되면 서서히 저항이 감소하다가 8%포인트 위치에서 최저점을 이루며 이는 실선속도 25노트에서 초기상태(0%LCG)에 비해 만재상태에서는 약 12.4%, 시운전 상태에서는 약 10%의 저항감소효과가 있었다. 그 이후 (10%LCG)부터는 다시 저항이 증가하게 되는데, 이는 선수트림이 커지게 되면서 선저의 활주면에 과도한 동적 압력이 발생하게 되고, 저항감소의 원인이 되었던 침수표면적의 감소로 인한 마찰저항의 감소보다 동적압력에 의한 압력증가 영향이 더 커지게 된 것으로 추측된다. 3. 나선상태에서보다 스프레이스트립(spray strip) 및 스케그 등과 같은 선형에 적합한 부가물을 부착하면 저항감소 및 직진성능 (course keeping ability) 향상 등의 이점이 있다. (이 논문의 결론 부분임)

별도의 엔진 구동형 소형 패키지 해수냉각시스템을 개발하기 위하여 압축기 회전수와 냉각수 유량 및 온도, 냉수 유량을 파라미터로 장치의 운전 특성을 파악한 결과 다음과 같은 결론을 얻었다. (1) 압축기 회전수와 증발기의 냉수 및 응축기의 냉각수 유량이 증가할수록 장치의 냉동능력은 증가하였으며, 압축기 회전수 및 냉각수 온도가 증가할수록 구동엔진의 연료소비량도 증가하였다. (2) 압축기 회전수와 냉각수 및 냉수의 유량이 증가할수록 냉각시스템의 성능계수는 증가하였으며, 냉각수 온도 및 압축기 회전수가 감소함에 따라서는 감소하였다. (3) 별도 엔진 구동용 소형 해수냉각장치 개발 및 운전조건 변화에 따른 시스템의 특성과 운전조건변화의 상관 관계를 파악할 수 있었으며, 시스템의 상용화 설계를 위한 기초자료를 얻을 수 있었다.

활주선 선형을 갖는 고속어선의 저항특성을 체계적으로 연구하기 위한 제 1단계로서 단면형상 및 장-폭비와 저항특성과의 관계에 대한 실험적 연구를 수행하였다. 본 연구는 새로운 고속 활주형 어선을 개발하기 위한 초기연구로서 다음의 내용을 포함하고 있다. - 4가지 단면형상에 대한 저항 특성 - 4가지 장-폭비에 대한 저항 특성

한국의 연안어선에 장비된 소형자기컴퍼스의 장비현황과 성능을 연구하기 위하여 소형어선 219척의 선박제원과 자기컴퍼스 이용에 대한 현장 설문조사를 행하고, 그 중에서 총톤수 4-6톤급의 실험대상 어선 4척을 선정하여 그 선박의 자기컴퍼스의 설치위치별 자차측정과 성능실험을 행하고, 이를 검사, 조사하였다. 주요한 결과를 요약하면 다음과 같다. 1. 조사 대상으로 한 총톤수 1-10 톤급 연안어선 219척 중 4톤 미만의 어선은 약 50%를 차지하였고, 자기컴퍼스의 제작연도가 20-30년 경과된 어선이 14척이나 되었으며, 자차수정용구를 비치한 어선은 2척 뿐이었다. 2. 컴퍼스의 설치위치별로 측정된 자차를 분석한 결과, 기관실위의 브리지갑판상과 브리지내의 컴퍼스받침대위 및 브리지위의 컴퍼스 갑판상에 자차수정을 한 자기컴퍼스를 설치하여 사용하면, 브리지내의 컴퍼스대의 위와 브리지위의 컴퍼스 갑판상에서는 잔재자차가 ±1~2 ˚ 정도였으나, 기관실 위의 브리지갑판상에서는 그 잔재자차가 ±5 ˚로 이곳은 컴퍼스 설치 장소로서 부적당함을 알 수 있었다. 3. 연안어선에서 사용 중인 자기컴퍼스의 제반특성은 표준규격인 반주기의 평균치가 12초 이상이어야 하고, 3회 이상 진동해야하는 기준에 미달하였으며, 측정치인 자기능률 1400 CGS는 소형컴퍼스의 표준치 400±30 CGS와는 큰 차이가 있었다. 4. 실험 대상 어선에 장비하고 있는 자기컴퍼스의 수반각은 6~16 ˚로서 한국표준규격인 1~1.5 ˚에 비해 너무 크게 나타나 그 표준규격에 부적합한 것으로 판단되었다.

Currently internal harbor and fishing port facilities are being maintained with the "Safety inspection and in-depth safety inspection detailed guideline" This is provided with the evaluation focusing on the safety and durability of the structure, based on the usability are not presented. In this study, we derive the evaluation items of the harbor and fishing port facilities for the transition from the maintenance of the existing system to the performance-based safety and maintenance system.