무도상 교량은 레일을 이음매판으로 부설하여 사용하고 있어 과다한 충격이나 궤도 틀림 등의 발생 우려로 인하여 열차의 고속주행이 어려운 실정이다. 열차의 주행안정성을 확보하기 위해서는 상호작용에 영향을 미치는 인자를 분석하여 동적 안전성에 대하여 검토할 필요가 있다. 이 연구에는 열차가 운용중인 판형교량의 현장계측을 통하여 궤도 구조 및 주거더의 충격계수를 도출하고 이를 기존연구와 비교 및 참고하여 열차의 주행속도를 고려한 충격계수의 추정식을 산정하였다. 궤도의 충격계수 산정식은 기존 연구에서 제안한 식과 유사하게 산정되었으며, 무도상교량 거더의 충격계수 산정식과 일본의 철도교 충격계수 식과 비교한 결과, 일본의 철도교 충격계수 식은 본 연구에서 산정한 거더의 충격계수 1배수 식과 2배수 식 사이에 존재하는 것으로 나타났다.

This paper discusses the influence of transverse reinforcement spacing and support width of concrete wide beam on shear performance. In order to evaluate the shear performance, a total of thirteen specimens were constructed and tested. The transverse reinforcement spacing, the number of legs and support width were considered as variables. From the test results, the shear strength equation of concrete wide beam is proposed for prediction of shear strength of concrete wide beam to consider the transverse reinforcement spacing and support width. It is shown that the proposed equation is able to predict shear strength reasonably well for concrete wide beam.

The fracture of mechanical structure is caused by internal cracks in the material. Particularly, the fracture can also be seen to happen under the stress that is lower than yield strength in case of high strength steel because of the crack happening from the defect inside the material. In this study, high strength steel with four holes near the center crack were designed by angle and fatigue experiments, and the simulation analyses to verify the experimental results were carried out. As the results of this study, the crack growth rates are shown to be 0.000485, 0.000434 and 0.000422 respectively at the inclined angles of center crack as 22.5°, 45° and 67.5°. The maximum deformation energies become 0.0848mJ, 0.0603mJ and 0.0582mJ respectively at the inclined angles of center crack as 22.5°, 45° and 67.5°. It is thought that this study result can be utilized as the basic data at the study on the material existing with the defects of crack and hole.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. T he experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

There is a growing demand for improving the welding quality by reducing the machining error and improving the quality of the machined surface in the beveling for the improvement of the welding groove of the thick plate. For this purpose, it is necessary to develop an automatic beveling machine that adopts a cutting method that replaces the conventional oxygen flame cutting method. In this study, the cutting characteristics according to the machining conditions were evaluated during the face milling applied to the thick plate welding groove. We measured and evaluated cutting force for the machining conditions such as cutting depth, feed rate, chamfer angle, workpiece material, and material of the tool. We expect that this study is used as basic data for designing the stiffness of the spindle, the strength of the fixture and the power of the spindle and the feeding device when designing the automatic beveling machine.

The residual stress analysis and fatigue test of a steel plate with a hole were performed in order to investigate the effects of the cold expansion on the fatigue life of the plate. The cold expansion method is a metal forming process by expanding a hole in order to induce compressive tangential residual stresses near the hole. In this research, a S45C steel plate of 3.2 mm thickness with a hole of 4.318 mm diameter was cold expanded by using a mandrel, resulting in a degree of expansion 1.47%. A significant amount of compressive tangential residual stress of 502 MPa at the hole surface was calculated using the finite element analysis and the compressive residual stress was more widely spreaded in the entry and exit planes than the mid plane in the plate thickness. The compressive tangential residual stresses showed a very beneficial influence on the fatigue life of the plate by increasing 1.2 to 2 times longer lives compared to the plate without cold expansion, depending on the applied load levels. Fatigue crack initiated and propagated at the hole surface of the mandrel entrance region, where relatively lower magnitude of compressive residual stress was found than the other region.

In this paper, we present the result of analytical investigation pertaining to the structural behavior of steel-concrete composite plate girder with arch-type web stiffener. In the arch-type web stiffener located in the compression side of web, infill concrete is cast to strengthen the arch-type stiffener and also to exert resisting force against compression force. This type of composite steel-concrete plate girder bridge is built and is in service. To understand the behavior thoroughly, analytical parametric study was conducted by using the finite element method. As a result it was found that the effect of arch-type stiffener with infill concrete is considerable for the design of such type composite girder bridge.

본 논문에서는 유공형 강판의 횡방향 보강간격에 따른 넓은 보의 전단성능을 실험적으로 평가하기 위하여 횡방향 전단보강 간격과 넓은 보의 유효깊이를 변수로 고려하였다. 시험체는 총 8개로 유공형 강판으로 전단보강한 시험체가 5개, 무보강 시험체가 3개이다. 균열 및 파괴유형, 변형률과 하중-변위 곡선을 분석하였다. 유공형 전단보강재의 전단강도 기여분을 분석하고, 횡방향 전단보강의 최대간격을 제안하였다. 횡방향 전단보강 개수가 2개인 시험체에 비해 3개인 시험체에서 전단강도가 크게 나타났으며 유효깊이가 증가할수록 전단강도가 크게 나타났다.

This study numerically investigates buckling behavior of press braked steel plates with a free edge. In order to improve structural stability during construction, the top flanges of press-braked U section girder are laterally braced by the installation of prefabricated half-deck. Thus, an unbraced length is taken as the longitudinal spacing of pockets on the half-deck, which are to make composite section. This study performed 3D finite element analyses to evaluate an equivalent effective width of cold-formed flange with a free edge. Through the parametric numerical analyses, the elastic buckling stresses of the cold-formed flanges with rounded corner in the cross-section were compared with those of general flat plates. Then, the equivalent effective width of the cold-formed (press-braked) flanges were numerically examined for some representative cases.

Main topics in this study is a new structural detail for connection between H-Steel or SRC column and flat plate slab. We carried out to evaluate the punching shear performance of H-steel or SRC column + RC slab system for vertical load and lateral load. From the test results structural characteristics - yield moment, yield rotation, maximum moment, deformation capabilities ect. - are obtained and evaluated. In this paper as a shear reinforcement for supporting region of plate closed stirrup type and shear band are used, and their test results are compared.

An experimental study was carried out to evaluate the punching shear performance of H-steel column + RC slab system for vertical load. Three specimens were constructed for interior column-slab system. All specimens were the same configuration and material properties except for columns such as RC column+flat plate slab and H-Steel column+flat plate slab. From the test results structural characteristics (maximum proof stress, maximum displacement, deformation capabilities and so on) are obtained and evaluated.

본 연구는 최근 세계적으로 이상기후에 의하여 빈번히 발생하는 지진재해에 의한 주요시설물 피해저감 및 신속복구에 대한 복합재료 적용에 관한 연구이다. 최근에 발생된 지진의 경우, 1차 지진에 의한 시설물 피해가 발생하고 이후 강력한 규모의 2차, 3차 여진이 지속적으로 발생하고 있다. 이에 대응하기 위하여 국외에서는 병원, 방송국 등과 같은 주요시설물의 초기 지진피해에 의한 피해와 손상을 신속히 응급복구하고 향후 2차 여진 및 관련 시설물에 대한 항구적인 보강대책을 제공할 수 있는 내진안전성 개선연구가 활발히 진행되고 있다. 본 논문에서 제시한 긴급복구용 파형강판-GFRP 내력패널의 경우, 강재료인 파형강판을 사이에 두고 외부를 GFRP 로 하여 GFRP-파형강판을 결합한 구조의 내력패널을 제작하여 기존 콘크리트 또는 강 프레임 구조물 내 지진에 의한 벽체손상 피해 발생 시 이들 손상된 벽체(조적조 또는 콘크리트 벽체)를 제거한 후 사전제작된 GFRP 내력벽 체를 적용, 대체 횡적 보강구조체로 시공하여 향후 피해저감 및 응급복구용으로 그 효율성을 극대화 및 내진 피해를 예방하고자 한다.

The flat plate slab system have many good features, which are design flexibilities, saving of story-height and economy of construction etc. But the study of flat plate slab system for H-steel column have been rare both at home and abroad. Recently high-rise residential and commercial buildings have been constructed in urban areas in Korea. The suggested dowel connection system is more likely to adoptable because it remarkably contribute to save inter story height and also to have many advantages compared with conventional steel works such as H-Steel frame + Deck plate slab system. This study aims at developing design method and program for connection between H-Steel column and flat plate slab system, which contribute to save significantly inter-story height.

This study presents an experimental study of the structural behavior for steel plate-concrete column-to-steel girder connections. Experiments were carried out to investigate the moment-rotation characteristics, failure behavior and ultimate moment capacity of these connections. The results of this experimental study involving three welded moment-resisting connections subjected to cyclic loading are presented. The specimens were fabricated at full scale to evaluate their hysteretic behavior. A description of the test specimens, the details of the joint, the test system and the testing methods are described. The test results showed that the structural behavior of these composite connections was influenced by the connection details.

In this study, flexural strength properties of SC shear walls were investigated through static pushover test. Failure modes and stiffness characteristics of SC shear walls under lateral loads were inspected by analyzing the experimental results. Main failures of unstiffened SC shear walls were found to be the type of bending shear failure due to the unbonding of the steel plate at the concrete interface. The ductility capacity of SC structures was also confirmed to be improved, which is considered to be a confining effect on steel plates in the longitudinal behavior of SC shear walls.

Steel plate concrete (SC) composite structure is now being recognized as a promising technology applicable to nuclear power plants as it is faster and suitable for modular construction. It is required to identify its dynamic characteristics prior to perform the seismic design of the SC structure. Particularly, the damping ratio of the structure is one of the critical design factors to control the dynamic response of structure. This paper compares the criteria for the damping ratios of each type of structures which are prescribed in the regulatory guide for the nuclear power plant. In order to identify the damping ratio of SC shear wall, this study made SC wall specimens and conducted experiments by cyclic lateral load tests and vibration tests with impact hammer. During the lateral loading test, SC wall specimens exhibited large ductile capacities with increasing amplitude of loading due to the confinement effects by the steel plate and the damping ratios increased until failure. The experimental results show that the damping ratios increased from about 6% to about 20% by increasing the load from the safe shutdown earthquake level to the ultimate strength level.

The special orthotropic plate theory is used for analysis of panels made of plate girders and cross beams. The cross-sections of cross-beams are WF types. The result is compared with that of the beam theory. According to the numerical examination given in this paper, the result by the plate theory is 2.43 times stiffer than that of beam theory.

본 연구는 최근 세계적으로 이상기후에 의하여 빈번히 발생하는 지진재해에 의한 주요시설물 피해저감 및 신속 복구에 대한 복합재료 적용에 관한 연구이다. 최근에 발생된 지진의 경우, 1차 지진에 의한 시설물 피해가 발생하 고 이후 강력한 규모의 2차, 3차 여진이 지속적으로 발생하고 있다. 이에 대응하기 위하여 국외에서는 병원, 방송국 등과 같은 주요시설물의 초기 지진피해에 의한 피해와 손상을 신속히 응급복구하고 향후 2차 여진 및 관련 시설물에 대한 항구적인 보강대책을 제공할 수 있는 내진안전성 개선연구가 활발히 진행되고 있다. 본 연구는 기존 건설 재료인 콘크리트와 강재의 경우 실제 지진재해 발생 시 기존시설물의 손상에 따른 응급복구용 재료로써 구조체 제작 및 시공에 다소 애로사항이 많다는 점을 착안, 저 중량 고강도 및 시공이 상대적으로 용이한 복합재료를 이용, 응급복구용 구조체로 제작하여 활용하는 방안을 제안하였다. 본 연구에서 제시한 긴급복구용 GFRP-파형강판 합성형 내력패널의 경우, 기존 콘크리트 또는 강 프레임 구조물 내 지진에 의한 벽체손상 피해 시 이들 손상된 벽체(조적조 또는 콘크리트 벽체)를 제거한 후 사전 제작된 GFRP- 파형강판 합성형 내력벽체를 적용, 대체 횡적 보강구조체로 신속 시공함으로써 향후 피해저감 및 응급복구용으로 그 효율성을 극대화하고 예방하는 내진공법을 개발하고자 한다. 연구에서 제안된 GFRP-파형강판 합성형 내력패널 의 경우, 상용 유한요소해석프로그램인 ABAQUS를 활용하여 3차원 해석모델링을 통하여 설계하며, 내력패널 내 구성요소의 경우 좌굴거동에 의한 파괴패턴을 기준으로 형상 및 재원을 결정하였다.