오스테나이트계 스테인리스강은 우수한 내식성, 내구성 및 내화성을 지닌다. 특히, 오스테나이트계 스테인리스강중의 대표인 STS304에 비해 저탄소를 함유하고 있는 STS304L은 현장용접 후 별도의 열처리 없이 높은 내입계부식성능을 지니고 있어 용접후 내입계 부식이 우려되는 부재접합에 적용할 수 있다. 본 연구에서는 티그(TIG)용접으로 필릿 용접된 STS304L 용접접합부의 용접재(용착금속부) 내력과 파단 메카니즘을 조사하고자 한다. 주요변수인 하중방향에 대한 용접선의 배치에 따라 TFW(하중직각방향 용접), LFW(하중방향용접), FW (하중방향용접과 하중직각방향 용접조합)시리즈의 실험체를 제작하여 인장실험을 실시하였고, 각각 인장파단,전단파단, 블록전단파단(인장 파단과 전단파단의 조합)이 발생하였다. 동일 용접길이에 대해 TFW 시리즈의 접합부가 가장 높은 내력을 나타났으며, 현행기준식( KBC2016/AISC2010)과 기존 연구자의 식에 의한 예측내력과 비교한 결과, TFW와 LFW접합부는 과소평가되었고 FW실험체는 과대평가되었다 .실제 파단 위험단면과 블록전단파단 메카니즘을 고려한 내력식을 제안하였다.

In this paper, block shear fracture behavior in base metal of fillet-welded connection fabricated with duplex stainless steel (STS329FLD) were investigated through experimental procedures. Main variables are weld lengths in the longitudinal and the transverse directions of applied force. As a result, test specimens failed by typical block shear facture (the combination of tensile fracture and shear-out fracture) in base metal not weld metal. Ultimate strength of the specimens tended to get higher with the increase of the weld lengths.

Recently, the use of duplex stainless steel which has a two-phase microstructure consisting of grains of ferritic and austenitic stainless steel has been increased in a variety of industrial fields. Especially, STS329FLD with lower nickel content and higher yield strength compared with austenitic stainless steel has been developed. In this paper, experiments have been conducted to investigate the structural behaviors of single shear duplex stainless steel(STS329FLD) bolted connection with four bolts. Specimens with relatively long end distance failed by block shear fracture accompanied with curling (out-of-plane deformation) and the curling reduced the ultimate strength.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. The experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

In this study, the artificial neural network (ANN) based estimation method for rotational stiffness of column-beam connection in steel moment frames is presented. Three story and one bay steel moment frame is used as the example structure. Natural periods and mode-shapes are used as the input data and the rotational stiffness values of connections are used as the output data.

This study investigates structural behaviors such as ultimate strength and weld metal fracture mechanism of carbon steel (SS400) fillet-welded connections with shielded metal arc welding (SMAW) through monotonic tensile test. Specimens of TFW series (transverse fillet weld against loading direction) and LFW series (longitudinal fillet weld) failed by tensile fracture and shear fracture, respectively in the weld metal of connections. Test strengths of specimens were compared according to welding direction and weld length.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. The experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

철골기둥-베이스 플레이트 접합부의 파괴유형은 베이스 플레이트 압축면과 인장면의 휨파괴, 앵커볼트의 인장파괴, 뽑힘, 전단파 괴, 그리고 콘크리트 기초파괴 및 철골기둥의 소성힌지발생에 따른 파괴이다. 본 연구에서는 핀접합 또는 강접합으로 가정하여 설계되는 노출 형 철골기둥-베이스 플레이트 접합부가 받을 수 있는 모멘트의 크기를 구하기 위하여, 한계상태 함수를 이용하여 철골기둥-베이스 플레이트 접합부의 휨성능 및 파괴유형을 예측하고 실험결과와 비교하였다. 한계상태함수를 이용하여 노출형 철골기둥-베이스 플레이트 접합부의 휨 성능을 비교적 정확히 예측할 수 있는 범위는 축력이 있는 경우, 앵커볼트의 항복 또는 철골기둥의 항복으로 판별되었을 때이며 축력이 없는 경 우, 베이스 플레이트의 항복으로 판별된 경우이다. 파괴유형까지 같이 고려할 경우, 축력이 있으며 앵커볼트의 항복으로 판별된 경우에만 한계 상태함수의 사용이 가능하다.

In Korea, Small-size buildings are not performed structural calculation. Also it does not assess the safety about lateral loads such like earthquake. In this study, We proposed the steel column bases that can be applied to small buildings. And We analyzed the Steel Column Bases flexural behavior.

Ultimate behaviors such as ultimate strength and fracture mechanism of fillet-welded connections with TIG(tungsten inert gas) welding have been investigated through test results. Main variables of specimens are weld length and welding direction against loading and ultimate strengths were compared according to the variables. Ultimate strengths were compared with current design predictions and modified design equations were proposed to consider the strength difference according to welding direction.

최근 도심지에 건설되는 건축물의 초고층화는 기둥에 작용하는 하중을 증가시켜 기둥단면 증가와 사용면적 확보의 어려움을 발생 시키고 있다. 이에 최근에는 CFT와 같은 합성기둥의 사용이 증가하고 있는 추세이다. 그러나 CFT 기둥의 경우 폐단면으로 이루어져 있어 보- 기둥 접합부 개발의 어려움과 성능저하의 문제가 발생하게 된다. 특히, 원형CFT 기둥과 외다이아프램을 이용한 접합상세 개발의 연구가 미비 한 실정이다. 이에 본 연구에서는 Y형 플레이트를 적용한 원형 CFT 기둥-H형강 보 접합부 접합상세를 개발하여 Y형 플레이트를 적용한 접합 부 구조성능에 영향을 미치는 Y형 플레이트 폭 및 두께를 주요변수로 설정하여 실험을 통해 구조성능을 평가하였다. 또한 실험체에 사용된 Y 형 플레이트는 설계기준에 제시된 장기허용인장력이 Y형 플레이트에 접합된 인장 측 플랜지의 축방향력 이하가 되도록 설계하여 파괴형태를 통해 Y형 플레이트의 구조적 안전성과 성능을 확인하고자 한다.

Austenitic stainless steels have excellent corrosion resistance, durability, aesthetic appeal, fire resistance etc. compared with ferritic stainless steels and so especially 304 stainless steels have been utilized widely in the exterior member of building structure. In this paper, ultimate behaviors such as ultimate strength and fracture mechanism of fillet-welded connections with TIG(tungsten inert gas) welding have been investigated through test results. Main variables of specimens are weld length and welding direction against loading and ultimate strengths were compared according to the variables.

The result of structural performance evaluation about circular CFT column-H shape steel beam which was performed as in previous study, even though we designed the Y type plate tension as below the axial force which was under design criteria, the flexure of steel beam was happened. For these reasons, in this study, to figure out the time of connections failure and the minimum value of parameters in order to evaluate the performance of advanced Y type plate in detail.

Based on AISC Design Guide-#1, limit-state function of steel column-base plate connection is defined. Comparison with test and numerical result, this method acculately predicts bending moment capacity of this connection.

In reinforced concrete structure, rebar connection method should be considered because of its structural role to resist the tensile stress and its structural load transmission with concrete in the concrete structure. Lapped splice and mechanical sleeve type connector have been traditionally used to connect rebar in the concrete structures. In this study, to examine the mechanical and failure behaviors of rebar bar connected by taper type coupler in the concrete member depending on connection type and condition, tensile tests of steel rebar with taper type coupler and flexible loading tests of concrete beams were conducted. Its tensile strength and flexible strength of the rebar connected by taper type coupler were compared and evaluated by mechanical behaviors of rebar. From this study, steel rebar connected by taper type coupler showed it has similar mechanical performance comparing with unconnected rebar, thus taper type coupler can be used in the rebar fabrication of reinforced concrete structure.

In this paper, the RC column-based joint connection part carry out loading test by reinforced hollow or extended Base Plate in order to confirm that RC joint punching shear reinforcement effect of applying the Base Plate. Base Plate thickness, extension length, size, and type as the variable, Base Plate suitable for the stress distribution and shape and dimensions confirmed through experiment and then reinforcing effect was analyzed. Experimentally, vertical load transmitted to the Base Plate from column to foundation is effective to stress distribution and then, type of hollow reinforcement more efficient than a closed. Through experiment, improve performance and ductility due to reinforcement and relative to the thickness of the existing foundation reduced even showed better performance than the existing. The behavior of the reinforced specimens be able to induce from brittle to ductile. Experiment on loading to destroy performed the pattern of cracks, destruction aspect before and after reinforcement.

본 연구에서는 모노파일지지구조의 고성능 그라우트연결부의 부착거동을 다루고 있다. 강관파일 연결부의 일체화를 위하여 섬유보강 고성능 그라우트를 개발하였으며, 재령 7일 압축강도 125MPa와 직인장강도 7.5MPa를 나타내었다. 축하중을 받는 상태에서의 그라우트의부착거동을 평가하기 위하여 강관파일에 그라우트를 충진하여 부착실험을 수행하였으며, 그 결과를 기존의 설계기준과 분석하였다. 실험변수는 섬유혼입율 (0%, 0.5% and 0.9%), 섬유의 형상비 (60 and 80)와 전단키의 높이와 간격의 비 (0.013 and 0.056)로 선정하였다. 실험결과 최대부착강도는 30.8MPa로 관찰되었으며, 섬유 혼입율보다는 전단키의 높이와 간격의 비가 부착강도에 영향을 미치는 것으로 분석되었다.

The SPC wall girder is connected to the vertical walls to enhance performance of wall-wall girder connection. The purpose of this study is to investigate the structural characteristics such as strength, Load-displacement relation of wall-wall girder connection under the monotonic load tests. The fracture pattern of the specimens induced positive moment at connection was steel plate separation from concrete in SPC Wall.

Recently, new cities of Korean coastal area, connective land·bridge and marine structure are increased. However, actually the evaluation method of pile head strengthening performance is not clearly defined, and, in spite of many technology proposed, its qualitative evaluation is not made. Therefore, the fact is that the prefabricated pile head strengthening stability is not verified. Therefore, it’s necessary to evaluate various technologies strategically and verify safety of precast file’s cap.