The purpose of this study is to evaluate the flexural performance of the SCP module fabricated using 40 MPa high-filling concrete and to verify the design flexural load presented in the INCA guidance of DNV. As a result, the maximum flexural load of the SCP module obtained through the structural test was 872 kN, the design flexural load and ultimate load were satisfied.

This paper presents development of an optimized cross section of high performance concrete median barrier(SB6). A series of numerical analyses and full-scale crash tests were was conducted to develop optimized section of SB6 concrete median barrier The suggested section of SB6 concrete median barrier satisfies all requirements provided by MOLIT(Ministry of Land, Infrastructure and Transport)

This study investigated the tensile properties of UHPC using by PE fiber. Test results showed that the UHPC with PE fiber has high tensile strain capacity compared with UHPC with steel fiber. PE Fiber content was not effective of the strength. But increase the PE fiber content was improved of tensile strain capacity.

We know that the failure of high performance concrete pavement occurs in the aspects of its structure, environment, material, and construction. We have been able to identify the reason why no construction should be permitted when average daily temperature is below 4 degree celsius. We must pay careful attention to the curing management and comply with the standards of concrete production and construction.

The purpose of this study is determining the effects of flexural behavior of aramid fibers in ultra high performance concrete. The 10 kinds of aramid fibers with different length, diameter and twisting were used. The flexural behavior was determined by bending tests on specimens, which was prepared by mixing 1 % of volume fractions of aramid fibers into ultra high performance concrete mortar. Consequently, the load-displacement relationship curves were obtained by using the test results for each kinds of aramid. While the specimen that contains the small diameter of aramid fiber gives the strong flexural strength due to large contact area between the fiber and concrete matrix, that specimen by small diameter of aramid fiber does not guarantee the ductile behavior of specimen like the steel fiber. But the length and twisting of aramid fiber gives the ductile behavior of ultra high performance concrete flexural specimen.

초고성능 콘크리트와 고연성 무시멘트 복합재료는 높은 압축강도 및 높은 연성 등 재료의 우수한 성능으로 인하여 유망한 건설재 료로 분류되고 있다. 이 연구의 목적은 초고성능 콘크리트와 고연성 무시멘트 복합재료의 압축강도와 인장거동에 대하여 실험적으로 조사하 여 성능을 비교하는 것이다. 이를 위하여 밀도, 압축강도, 일축인장실험 등 일련의 실험을 수행하였다. 실험결과 알칼리 활성 슬래그 기반 고연 성 무시멘트 복합재료의 압축강도와 인장강도는 초고성능 콘크리트의 압축강도와 인장강도에 비하여 낮게 나타났지만, 인장하중 하에서 알칼 리 활성 슬래그 기반 고연성 무시멘트 복합재료의 인장변형성능 및 인성은 초고성능 콘크리트의 인장변형성능 및 인성에 비하여 높은 것으로 나타났다. 또한 알칼리 활성 슬래그 기반 무시멘트 페이스트에 폴리에틸렌섬유를 보강하여 7.89 %에 달하는 높은 인장변형성능을 확보할 수 있는 것으로 나타났다.

The purpose of this study is to establish a reasonable analytical method for the estimation of overall behavior characteristic from cracking to yielding of rebar and crushing of concrete and seismic performance of reinforced concrete shear wall with high-strength reinforcing bar. A total of 8 specimens of reinforced concrete walls which have constant aspect ratio and a variety of variables such as reinforcement ratio, reinforcement yielding strength, reinforcement details, concrete design strength, section shape and whether lateral restraint hoop were selected and the analysis was performed by using a non-linear finite element analysis program (RCAHEST) applying the proposed constitutive equation by the authors. The mean and coefficient of variation for maximum load from the experiment and analysis results was predicted 1.04 and 8%. The mean and coefficient of variation for displacement corresponding maximum load from the experiment and analysis results was predicted 1.17 and 19% respectively. The analytical results were predicted relatively well the fracture mode and the overall behavior until fracture for all specimens. These results are expected to be used as basic data for application of high-strength reinforcing bar to design codes in the future.

This paper describes the experimental results for the structural performance of full-scale coupling beams with different reinforcement layout (diagonal and horizontal). For the reinforcements of the coupling beams, high-strength steel bars(SD500 and SD600) were used in order to improve workability and economic feasibility. The rigid steel frames and linked joints were used to maintain the clear span length (distance between both shear walls) of the coupling beam during the cyclic loading. Experimental results indicated that the diagonally reinforced coupling beam specimen could exhibit more ductile behavior compared to horizontally reinforced specimen. ACI318-14 code is applicable to design of coupling beam with diagonally reinforcement, however, that is overestimating the strength of horizontally reinforced coupling beam. It is remarkable that effective elastic stiffness values of both reinforcement details coupling beam significantly lees than ASCE 41-13.

The purpose of this experimental research is to evaluate the mechanical properties of high performance concrete using amorphous steel fiber and organic fiber. For this purpose, the hybrid fiber reinforced concrete containing amorphous steel fiber(ASF) and polyamide(PA) fiber were made according to their total volume fraction of 0.5% for water-binder ratio of 33%, and then the characteristics such as the workability, compressive strength, and direct tension strength of those were evaluated. It was observed from the test results that the workability and compressive strength was decreased with increasing ASF and decreasing PA fiber. but the direct tension strength was on the whole increased with increasing ASF and decreasing PA fiber.

This study investigated the tensile property of high performance concrete according to addition of plastic bead. Test results showed that the addition of PS beads induced the decrease of crack width and increase of number of cracks while maintaining tensile strength and tensile strain capacity.

The research was introduced a newly atypical beam with ultra-high strength concrete. Ultra high strength concrete has compressive strengths up to 200MPa, tensile strengths up to 20 MPa and tensile strain up to 5%. A series of the developed beams was designed an irregular cross-section by precast and form-work technologies. They evaluated the flexural performance by experiment and analysis comparing with conventional reinforced concrete beams.

본 논문에서는 UHPC 바닥판과 강재 거더를 이용하여 합성보를 구성할 때, UHPC 바닥판의 높은 강도와 강성으로 인하여 합성보 구성 시에 강재 거더의 상부 플랜지를 없앤 역T형 거더를 적용하고자 하였다. 그러나 현재까지 강재 복부에 설치되는 전단연결재에 대한 거동, 역T형 강거더 합성보의 휨거동 특성 등은 실험 및 이론적으로 평가된 적이 거의 없는 실정이다. 이를 위하여 UHPC 압축강도, 전단연결재 간격 및 바닥판 두께 등을 변수로 하는 역T형 거더와 UHPC바닥판 합성보 16개의 휨거동 실험결과를 근간으로 하여 실험결과와 UHPC의 인장연화 거동을 고려한 재료모델 해석결과를 비교하였다. 역해석에 의한 인장연화곡선에서 UHPC의 인장강도는 6.57 MPa(120MPa의 경우) 및 9.57 MPa(150MPa의 경우)를 나타내고 있으며, 전단연결재 간격이 좁을수록 실험결과와 해석결과가 명확하게 근접하는 겻으로 나타났으며, 바닥 판 두께가 두꺼우며 UHPC 압축강도가 작을수록 동일한 경향이나, 이 영향은 다소 작은 것으로 나타났다. 따라서 실험결과와 해석결과를 종합 적으로 비교하면, UHPC 합성보의 실험결과와 해석결과는 비교적 잘 일치하고 있으므로 재료 실험으로부터 산정된 인장연화곡선은 UHPC의 실제 거동을 합리적으로 반영한다고 판단된다.

This study investigated the compressive strength of UHPC according to fiber combination. Test results showed that the PE, PVA and basalt fiber mixtures have lower compressive strength than steel fiber mixture. Compressive strength reduction ratio of PE, PVA and basalt fiber mixtures were 0.95, 0.96 and 0.86, respectively.

This study investigated physcal properties of high performance concrete(HPC) using the garnet(GA) and Fly-ash(FA) under high temperature. After heating up the concrete, its appearance, failure mode, residual compressive strength, weight reduction ratio and other physical properties of concrete, it was mixed with nylon(Ny), polypropylene(PP), steel fiber(SF). The specimen was exposed to 100~800℃ and its crack control, spalling prevention and other physical characteristics were reviewed.

This paper concerns the flexural behavior of hybrid steel fiber-reinforced ultra high performance concrete (UHPC) beams. It presents experimental research results of hybrid steel fiber-reinforced UHPC with steel fiber content of 1.5% by volume and steel reinforcement ratio of less than 0.02. The comparison of moment-curvature curves of the numerical analysis results with the test results shows a resonable agreement.

This paper is to evaluate the flexural characteristics of 180MPa Ultra High Performance Concrete and reinforcing steel. In this study, the bending test is performed to evaluate the flexural characteristics considering lap-splice length. The stability of the lap-splice length proposed the structural design codes are evaluated on load-displacement. The results confirmed that the ductility has increased when the lap-splice has increased.

This paper is to evaluate the flexural characteristics of 180MPa Ultra High Performance Concrete and reinforcing steel. In this study, the bending test is performed to evaluate the flexural characteristics considering cover depth. The stability of the cover depth proposed the structural design codes are evaluated on load-displacement. The results confirmed that the ductility has increased when the cover depth has increased.

초고성능 콘크리트는 높은 강도와 유동성을 갖는 우수한 재료 특성을 나타내는 콘크리트이다. 그러나 고연성 시멘트 복합체에 비하여 낮은 연성을 나타낸다. 이 연구에서는 강섬유와 마이크로섬유의 조합이 초고성능 콘크리트의 인장거동에 미치는 영향을 조사하였다. 이를 위하여 강섬유와 폴리에틸렌, 폴리비닐알코올, 현무암섬유 조합에 따라 4가지 초고성능 콘크리트 배합을 결정하였고, 인장거동을 평가하기 위하여 직접인장 실험을 수행하였다. 또한 마이크로섬유가 제조과정에서 의도하지 않은 과도한 기포를 생성하는지를 확인하기 위하여 밀도 실험을 수행하였다. 실험결과 인장강도가 높은 폴리에틸렌섬유는 초고성능 콘크리트의 인장거동을 향상시키는데 효과적임을 확인하였고, 현무암섬유는 초고성능 콘크리트의 균열강도 및 인장강도를 증가시키는데 효과적임을 확인하였다. 또한 마이크로섬유가 의도하지 않은 기포를 생성하지 않는다는 것도 확인하였다.

이 연구에서는 초고성능 콘크리트 (UHPC)와 보통 콘크리트 (NSC)간 계면부착강도에 관한 연구를 수행하였다. UHPC를 보수⋅보강재 로 활용하기 위한 기존의 부착강도에 관한 연구와 달리, UHPC를 프리캐스트 합성부재로 활용하기 위한 연구에 초점을 맞추었으며, 여기 에 영향을 미칠 수 있는 다양한 요인에 대하여 검토하였다. 기존 연구들을 분석한 결과, UHPC-NSC 계면 부착강도에 영향을 미칠 수 있는 요인으로는 계면의 형상, 합성 전 UHPC의 경화 진행상태, 합성 전 UHPC의 수분 흡수상태, 그리고 합성 후 양생장소와 같이 크게 4가지 로 구분되었다. 계면의 형상을 변수로 한 실험에서는 형상에 따라 각기 다른 파괴모드가 나타났으며, 기존 연구에서 확인되지 않았던 거칠 게 처리한 UHPC 계면 일부가 파괴되는 새로운 파괴모드가 발견되었다. 합성 전 UHPC의 경화진행 상태가 부착강도에 영향을 미치는 것 으로 나타났으며, 이러한 영향은 부착 파괴모드에 따라 다르게 나타났다. 또한, 합성 전 UHPC의 수분상태가 부착강도에 영향을 주었으며, UHPC의 양생방법에 따라 서로 상반되는 결과를 보였다. 마지막으로, 합성한 시편의 양생조건 역시 계면 부착강도에 영향을 미친다는 것 을 확인하였다.