본 연구는 육계사육에서 횃대의 제공효과와 최적 두께를 구명하기 위해 진행하였다. 12일령 육계(RossⅹRoss) 288수를 24개의 독립된 공간(7.3 수/m2)에 균등한 평균 체중으로 분배하여 42일령까지 사양실험을 실시하였다. 그룹은 일반 평사사육(대조구)과 3개의 횃대 처리구(두께: 3, 4 및 5 cm)인 총 4개로 구성하였으며, 각 그룹은 6반복과 반복당 12수씩으로 배치하였다. 각 반복 별로 횃대의 길이는 1.3 m (0.11 m/수)로서 높이 15 cm에 설치하였다. 조사항목으로 육계의 생산성, footpad dermatitis (FPD)과 hock burn (HB) 지표 및 횃대이용성을 확인하였다. 본 연구결과, 육계사육에서 횃대의 유무와 두께에 따른 체중, 증체량, 사료섭취량 및 사료요구율은 통계적 차이가 없었다. FPD는 처리구 간 유의적 차이가 없었으나, HB 지표는 4와 5 cm의 횃대를 제공한 처리구에서 일반 평사와 3 cm 두께의 횃대에서 사육한 육계에 비해 개선되었다(p<0.05). 육계가 횃대를 이용한 시간은 사육전기(12~24일령)에는 차이가 없었으나, 사육후기(25~42일령)에 횃대를 이용한 총 시간은 5 cm 두께에서 3과 4 cm 두께보다 높았으며(p<0.05), 올라간 횟수에 비해서도 더 많은 시간을 보냈다(p<0.05). 그러므로 횃대는 육계의 다리질병을 줄이며, 4~5 cm의 두께를 이용하는 것이 가장 적합할 것으로 사료된다.

One disadvantage of deep cycle flooded lead-acid batteries is increasing water loss caused by use of (+) Pb-Sb / () Pb-Sb alloy grid. Water loss is generated by the emission of hydrogen gas from the () electrode during battery charging. In this paper, we maintain cycle life aspect through the development of hybrid flooded lead-acid batteries to which a (+) Pb- Sb / () Pb-Ca grid is applied and deal with the improvement of water loss. The amount of water loss compared to that of the () Pb-Sb grid decreased when Ca was added to the () Pb grid. For the () Pb-Ca grid, it was confirmed that the time to reach 0.0 V, at which water decomposition occurs, was increased compared to that of the () Pb-Sb grid at the NPV (Negative Potential Voltage). In the cycle life test conducted with the BCI (Battery Council International) standard, compared to the (+) Pb-Ca grid, the (+) Pb-Sb grid increased the life cycle of the batteries and the (+) Pb-Ca grid showed an early end of life due to PbO corrosion layer generation, as determined through SEM / EDS and Tear Down analysis. In conclusion, by addition of Sb to (+) Pb grid and Ca to () Pb grid, we developed a hybrid flooded lead-acid battery that meets user requirements to improve water loss characteristics and preserve cycle life characteristics.

To cope with automobile exhaust gas regulations, ISG and charging control systems are applied to HEV vehicles for the purpose of improving fuel economy. These systems require quick charge-discharge performance of high current. Therefore, a Module of the AGM battery with high energy density and EDLC(Electric Double Layer Capacitor) with high power density are constructed to study the charging and discharging behavior. In CCA, which evaluates the starting performance at -18 oC & 30 oC with high current, EDLC contributed for about 8 sec at the beginning. At 0 oC CA (Charge Acceptance), the initial Charging current of the AGM/EDLC Module, is twice that of the AGM lead acid battery. To play the role of EDLC during high-current rapid charging and discharging, the condition of the AGM lead-acid battery is optimally maintained. As a result of a Standard of Battery Association of Japan (SBA) S0101 test, the service life of the Module of the AGM Lead Acid Battery/EDLC is found to improve by 2 times compared to that of the AGM Lead Acid Battery.

To cope with automobile exhaust gas regulations, ISG (Idling Stop & Go) and charging control systems are applied to HEVs (Hybrid Electric Vehicle) for the purpose of improving fuel economy. These systems require quick charge/discharge performance at high current. To satisfy this characteristic, improvement of the positive electrode plate is studied to improve the charge/discharge process and performance of AGM(Absorbent Glass Mat) lead-acid batteries applied to ISG automotive systems. The bonding between grid and A.M (Active Material) can be improved by applying the Sand-Blasting method to provide roughness to the surface of the positive grid. When the Sand-Blasting method is applied with conditions of ball speed 1,000 rpm and conveyor speed 5 M/min, ideal bonding is achieved between grid and A.M. The positive plate of each condition is applied to the AGM LAB (Absorbent Glass Mat Lead Acid Battery); then, the performance and ISG life characteristics are tested by the vehicle battery test method. In CCA, which evaluates the starting performance at -18 oC and 30 oC with high current, the advanced AGM LAB improves about 25 %. At 0 oC CA (Charge Acceptance), the initial charging current of the advanced AGM LAB increases about 25 %. Improving the bonding between the grid and A.M. by roughening the grid surface improves the flow of current and lowers the resistance, which is considered to have a significant effect on the high current charging/discharging area. In a Standard of Battery Association of Japan (SBA) S0101 test, after 300 A discharge, the voltage of the advanced AGM LAB with the Sand-Blasting method grid was 0.059 V higher than that of untreated grid. As the cycle progresses, the gap widens to 0.13 V at the point of 10,800 cycles. As the bonding between grid and A.M. increases through the Sand Blasting method, the slope of the discharge voltage declines gradually as the cycle progresses, showing excellent battery life characteristics. It is believed that system will exhibit excellent characteristics in the vehicle environment of the ISG system, in which charge/discharge occurs over a short time.

본 연구는 폐탄광에서 산림으로 복구된 지역의 임목, 낙엽층, 토양, 그리고 산림의 총 탄소 저장량을 추정하고, 수종별 탄소 저장량 차이를 비교하기 위해 수행되었다. 이를 위하여 강원도, 경상북도, 전라남도의 폐탄광 산림복구지에서 자작나무, 잣나무, 소나무류 (소나무, 리기다소나무, 곰솔)가 서로 다른 시기에 식재된 산림과 주변의 일반 산림을 조사하였다. 일반 산림에 비하여 폐탄광 산림복구지 내 낙엽층 및 토양 (ton C ha-1; 자작나무: 3.31±0.59 및 28.62±2.86, 잣나무: 3.60±0.93 및 22.26±5.72, 소나무류: 4.65±0.92 및 19.95±3.90), 그리고 산림의 총 탄소 저장량 (ton C ha-1; 자작나무: 54.81±7.22, 잣나무: 47.29±8.97, 소 나무류: 45.50±6.31)은 낮게 나타났으며, 임목 탄소 저장량 (ton C ha-1; 자작나무: 22.57±6.18, 잣나무: 21.17±8.76, 소나무류: 20.80±6.40)은 자작나무가 식재된 곳에서만 낮은 결과가 나타났다. 수종별로 토양 탄소 저장량을 제외한 임목, 낙엽층, 산림의 총 탄소 저장량에서 차이가 나타나지 않았으며, 임목 및 산림의 총 탄소 저장량은 복구 후 경과 시간에 따라 증가하는 경향을 보였다. 한편, 폐탄광 산림복 구지의 자작나무와 소나무류에서 토양 pH 및 CEC가 낮게 나타났으며, 수종별 불안정탄소, 유효인산, 미생물 바이오 매스 탄소가 일반 산림토양보다 2배 이상 낮은 결과를 보 였다. 폐탄광 산림복구지에 석회 및 유기질 비료의 시비와 경운을 통해 토양 성질을 개선하고, 가지치기 및 간벌 등 과 같은 산림관리로 임목 생육을 증진시키면 폐탄광 산림 복구지 내 탄소 저장량을 증가시킬 수 있을 것으로 기대된다.

본 논문에서는 해양플랜트에 주로 사용되는 알루미늄 사다리의 독자 모델을 개발하기 위하여, 개량형 알루미늄 합금(6082-T6) 을 적용하고 국제 기준에 부합한 구조강도 설계를 하였다. 국제기준은 ISO, NORSOK, Austria Standard를 참고하였으며, 모든 조건이 만족할 수 있도록 하중 조합을 하였다. 설계된 모델은 유한요소법 [Finite elements method]을 근간으로 하는 해양플랜트 전용 해석프로그램인 SACS를 사용하여 구조 안전성을 검증하여 응력 및 처짐이 모두 허용기준 이내에 만족함을 확인하였다. 개발모델은 모든 허용기준을 만족하면서도 가볍고, 생산성이 향상되어 향후 많은 분야에서 사용이 될 것으로 기대해본다.

선박 및 해양구조물에서 사용하고 있는 고강도 알루미늄 합금들은 스틸과 비교해서 많은 이점을 가지고 있다. 최근 고강도 알루미늄 합금들은 육상 및 해양에 폭넓게 사용되고 있으며, 특히, 특수목적 선박의 선체 외판구조에 많이 이용되고 있고, 교량 구조물에 사용되는 상자 구조물, 그리고 고정식 해양플랫폼의 상부구조에서 소비율이 증가하고 있다. 알루미늄 재료는 스틸보다 1/3의 중량 구성비를 통하여, 구성 중량을 줄이게 하여 연비 절감을 가능하게 한다. 일반적인 강구조물의 응력-변형률 관계와 비교하면, 용접가공에 따라 발생하는 열영향부의 존재로 인하여 상당히 다르게 나타난다. 왜냐하면, 강구조물과 비교하면 열전도율이 높아서, 열영향부(heat affected zone, HAZ)가 남아 있어 구조 강도 저하를 가져온다. 본 논문에서는 MIG(Metal inert gas) 용접 때문에 발생하는 열영향부를 고려하고, 종방향 압축 하중에 대한 알루미늄 보강판의 좌굴 및 최종강도 특성을 분석하였다. MIG 용접에 따른 열영향부를 고려한 경우, 좌굴 및 최종강도 모두 감소하며, 열영향부의 범위가 15 mm부터 항복 이후 에너지 소실률이 크게 나타나며, 25 mm 이상부터는 그 차이가 크지 않다. 따라서, 알루미늄 합금재료를 적용한 보강판의 구조 거동을 파악하기 위해서는 열영향부 영향에 대한 검토 및 분석이 중요하다.

The performance characteristics of a lead acid battery are investigated with the content of Sodium Perborate Tetrahydrate (SPT, NaBO3·4H2O) in a positive plate active material. SPT, which reacts with water to form hydrogen peroxide, is applied as an additive in the positive plate active material to increase adhesion between the substrate (positive plate) and the active material; this phenomenon is caused by a chemical reaction on the surface of substrate. A positive plate with the increasing content of SPT is prepared to compare its properties. It is confirmed that the oxide layer increases at the interface between the substrate and the active material with increasing content of SPT; this is proven to be an oxide layer through EDS analysis. Battery performance is confirmed: when SPT content is 2.0 wt%, the charging acceptance and high rate discharge properties are improved. In addition, the lifetime performance according to the Standard of Battery Association of Japan (SBA) S0101 test is improved with increasing content of SPT.

Nb-Si-B alloys with Nb-rich compositions are fabricated by spark plasma sintering for high-temperature structural applications. Three compositions are selected: 75 at% Nb (Nb0.7), 82 at% Nb (Nb1.5), and 88 at% Nb (Nb3), the atomic ratio of Si to B being 2. The microstructures of the prepared alloys are composed of Nb and T2 phases. The T2 phase is an intermetallic compound with a stoichiometry of Nb5Si3-xBx (0 ≤ x ≤ 2). In some previous studies, Nb-Si- B alloys have been prepared by spark plasma sintering (SPS) using Nb and T2 powders (SPS 1). In the present work, the same alloys are prepared by the SPS process (SPS 2) using Nb powders and hypereutectic alloy powders with composition 67at%Nb-22at%Si-11at%B (Nb67). The Nb67 alloy powders comprise T2 and eutectic (T2 + Nb) phases. The microstructures and hardness of the samples prepared in the present work have been compared with those previously reported; the samples prepared in this study exhibit finer and more uniform microstructures and higher hardness.

북베트남의 컨테이너 터미널을 주제로 한 연구는 다수 있지만, 선박의 대기시간이나 화물처리에 관련한 비용 측면에서의 경쟁을 다룬 연구는 거의 없다. 이 논문은 북 베트남에 입지한 컨테이너 터미널의 TEU당 평균대기비용을 추산해 본 연구다. 우선 대기 행렬이론을 적용하여 평균대기시간을 추산한 뒤, 불확실성 이론을 적용하여 선박의 일당 비용을 추산할 것이다. 그리고 각 터미널의 하역능력 내지 물동량 처리율과 관련하여 TEU당 일련의 대기시간을 산정하기 위해 시뮬레이션을 실시하였다. 추산된 일련의 대기시간을 근거로 하여 각 항만의 평균대기시간과 물동량 처리율 / 하역률 간의 관계를 제시하기 위한 함수를 추정하기 위해 비선형회귀법을 적용하였다. 연구 결과는 북베트남의 컨테이너 터미널간의 경쟁상황에 관한 후속 연구에서 게임이론을 적용하는 데 이용될 수 있을 것 이다.

Currently, satellite images act as essential and important data in water resources, environment, and ecology as well as information of geographic information system. In this paper, we will investigate basic characteristics of satellite images, especially application examples in water resources. In recent years, researches on spatial and temporal characteristics of large-scale regions utilizing the advantages of satellite imagery have been actively conducted for fundamental hydrological components such as evapotranspiration, soil moisture and natural disasters such as drought, flood, and heavy snow. Furthermore, it is possible to analyze temporal and spatial characteristics such as vegetation characteristics, plant production, net primary production, turbidity of water bodies, chlorophyll concentration, and water quality by using various image information utilizing various sensor information of satellites. Korea is planning to launch a satellite for water resources and environment in the near future, so various researches are expected to be activated on this field.

인도네시아의 열대 이탄지는 황폐화되고 농경지 및 조림지로 전용되어왔다. 수로는 열대 이탄지의 지하수위를 관리하고 작물의 생산성을 높이기 위해 설치되었으나, 열대 이탄지의 구조를 파괴하고 침하 및 산불 발생 위험을 증가시켰다. 이에 따라, 인도네시아 정부는 수로로 인한 문제를 막기 위한 정책과 모라토리엄을 마련하였다. 그리고 해당 정책들에 따라 이탄지 재습지화에 관한 시범사업들이 일부 수행되었다. 우리나라가 열대 이탄지를 재습지화 한다면 추후 탄소배출권을 확보할 수 있는 가능성이 있으므로, 적절한 재습지화에 관한 자료가 필요하다. 이에 따라, 본 연구에서는 열대 이탄지에 적용되는 정책의 흐름을 조사하고 이 시범사업들의 설치 계획, 고려사항, 댐 설계, 재료, 설치 방법, 모니터링 방법, 그리고 소요 시간 및 비용 등에 대해 분석하였다. 이탄층의 깊이가 3 m 이상인 지역은 개발이 제한되고 개발 허가 발급이 중단되었으며, 복원을 위한 수로차단이 설치되었다. 이 지역에서는 댐의 지속성과 지역 이해당사자들의 참여를 독려하는 것이 우선순위로 여겨졌다. 개발 허가지역의 경우에는 개벌과 화전이 금지되었으며, 지하수위를 유지하기 위한 수로차단에 목적을 두었고, 수로차단을 설치할 때에는 작업 및 비용의 효율성이 우선적으로 고려되었다. 조사 결과를 바탕으로 본 연구에서는 인도네시아 열대 이탄지의 규제 적용 및 수로차단 설치 시 적용할 수 있는 방안들을 제시하였다. 이러한 결과는 동남아시아 지역의 배수된 열대 이탄지에 적합한 수로차단을 계획하는 데 기여할 수 있을 것으로 사료된다.

This study was conducted in order to investigate the effects that the difference of planting time by a method of cultivation in the non-heated greenhouse and the open field with spring planting had on growth and yield. With regard to the tested variety of Momordica charantia, variety ‘Dragon’ (Japan Yae 農藝) was selected. And 3 treatments on March 20, April 5 and April 20 for the greenhouse cultivation and 3 treatments on April 20, May 5 and May 20 for the open-field cultivation 1 month later than those for the greenhouse cultivation were planted by the randomized complete block design, and 4 secondary vines were trained. In the results of examining 15-day average atmospheric temperature after planting according to the methods of greenhouse and open-field cultivation and planting time, it was shown that there was a tendency for atmospheric temperature inside the greenhouse to decrease as the planting time was moved up. In particular, the average atmospheric temperature was 16.7oC when seedling was planted on April 20 in the open-field cultivation, which was approximately equal to 17.0oC of the average atmospheric temperature when a seedling was planted on March 20 in the greenhouse cultivation. With regard to the date of first harvest by the method of cultivation, it was shown that there was a tendency for the date of first harvest to be earlier in the greenhouse cultivation than in the open-field cultivation, and the date of first harvest was moved up as a seedling was planted earlier for the planting period. The number and weight of harvested fruits per plant showed a tendency which was almost similar to that of total number of harvest days and number of harvests. Thus, the number of fruits was 189 and the weight of fruits was 31,649g in case of the greenhouse cultivation and planting on March 20, which were maximum. In case of planting on the latest planting date : May 20 in the open-field cultivation, the number of fruits was 77 and the weight of fruits was 12,502g, which were at a level of 40% of those of planting on March 20 in the greenhouse cultivation 2 months earlier. The total yield per 10a was 10,228kg in the greenhouse cultivation and was 2.2 times as heavy as 4,607kg in the open-field cultivation with regard to the method of cultivation. For the planting period in the greenhouse cultivation, it was 10,539kg and 10,517kg in planting on March 20 and April 5, which was higher by 9% than 9,629kg in planting on April 20. And in the open-field cultivation, it was 4,785kg in planting on April 20 and 4,872kg in planting on May 5, which was higher by 15~17% than 4,163kg in planting on May 20. Taking the above results into account, it is considered proper to plant Momordica charantia from March 20 to April 5 for the greenhouse cultivation and from April 20 to May 5 or thereabouts when a risk of late frost is gone for the open-field cultivation in southern area.

Cobalt nano-rods were fabricated using a template-free electrochemical-deposition process. The structure of cobalt electro-deposits strongly depends on the electrolyte composition and on the density of the applied current. In particular, as the content of boric acid increased in the electrolyte, deposits of semi-spherical nuclei formed, and then grew into one-dimensional nano-rods. From analysis of the electro-deposits created under the conditions of continuous and pulsed current, it is suggested that the distribution of the active species around the electrode/electrolyte interface, and their transport, might be an important factor affecting the shape of the deposits. When transport of the active species was suppressed by lowering the deposition temperature, more of the well-defined nano-rod structures were obtained. The optimal conditions for the preparation of well-defined nano-rods were determined by observing the morphologies resulting from different deposition conditions. The maximum height of the cobalt nano-rods created in this work was 1μm and it had a diameter of 200 nm. Structural analysis proved that the nano-rods have preferred orientations of (111).