본 연구는 동물교감활동 프로그램을 시행하면서 대학생과 동물 간의 유대감을 형성시 킴으로써 우울과 스트레스를 감소 시키는 것에 목적으로 두었다. 본 연구는 대학생을 대 상으로 아론 벡의 우울척도, 스트레스 인지 검사, 빗속의 사람 그림검사 방법을 사용하여 동물교감활동 프로그램을 진행한 후 우울, 스트레스의 변화에 대해서 살펴보았다. 본 연 구의 결과는 다음과 같다. 첫째, 동물교감활동이 대학생의 우울감을 낮추는 데 긍정적인 영향을 주었다. 둘째, 동물교감활동이 대학생의 스트레스를 낮추는 데 유의한 효과를 보 였다. 본 연구는 대학생을 대상으로 한 동물교감활동의 효과성을 검증함으로써 동물교감 활동의 연구에 기여한 것에 의의가 있다.

연층을 가지는 건축물들의 피해사례가 관측됨에 따라 기존 건축물 내진성능평가시 수직비정형의 고려가 중요해졌다. 하지만 기존 방법은 수직비정형을 충분히 반영하기 어렵기 때문에 수직비정형을 가지는 건축물에 대해 내진성능을 과소 혹은 과대평가할 여지가 있다. 본 연구는 강성기반 연층비(Soft Story Ratio, SSR)를 이용해 수직비정형 건축물의 내진성능평가 기법을 개발하는데 목적이 있다. SSR은 변위에 대한 요구량과 능력의 비율을 나타내고, 강성차이에 의한 수직비정형을 고려하여 건축물의 변위집중 비율을 의미하는 파라미터다. 1층 기둥을 변수로 하는 필로티 건축물 네 개를 대상으로 개발한 내진성능평가 기법을 기존의 내진성능평가 기법과 비교하였다. 기존 기법은 수직비정형이 극대화되는 모델에 대해 내진성능을 과대평가하는 경우가 발생하였다. 반면 제안된 기법은 모든 모델에 대해서 상세평가의 결과와 동일했다. 따라서 제안하는 내진성능평가 기법은 수직비정형이 극대화되는 필로티 건축물에서 기존의 방법보다 정밀하게 내진성능평가 결과를 제공할 수 있다고 사료된다.

To cope with automobile exhaust gas regulations, ISG and charging control systems are applied to HEV vehicles for the purpose of improving fuel economy. These systems require quick charge-discharge performance of high current. Therefore, a Module of the AGM battery with high energy density and EDLC(Electric Double Layer Capacitor) with high power density are constructed to study the charging and discharging behavior. In CCA, which evaluates the starting performance at -18 oC & 30 oC with high current, EDLC contributed for about 8 sec at the beginning. At 0 oC CA (Charge Acceptance), the initial Charging current of the AGM/EDLC Module, is twice that of the AGM lead acid battery. To play the role of EDLC during high-current rapid charging and discharging, the condition of the AGM lead-acid battery is optimally maintained. As a result of a Standard of Battery Association of Japan (SBA) S0101 test, the service life of the Module of the AGM Lead Acid Battery/EDLC is found to improve by 2 times compared to that of the AGM Lead Acid Battery.

To cope with automobile exhaust gas regulations, ISG (Idling Stop & Go) and charging control systems are applied to HEVs (Hybrid Electric Vehicle) for the purpose of improving fuel economy. These systems require quick charge/discharge performance at high current. To satisfy this characteristic, improvement of the positive electrode plate is studied to improve the charge/discharge process and performance of AGM(Absorbent Glass Mat) lead-acid batteries applied to ISG automotive systems. The bonding between grid and A.M (Active Material) can be improved by applying the Sand-Blasting method to provide roughness to the surface of the positive grid. When the Sand-Blasting method is applied with conditions of ball speed 1,000 rpm and conveyor speed 5 M/min, ideal bonding is achieved between grid and A.M. The positive plate of each condition is applied to the AGM LAB (Absorbent Glass Mat Lead Acid Battery); then, the performance and ISG life characteristics are tested by the vehicle battery test method. In CCA, which evaluates the starting performance at -18 oC and 30 oC with high current, the advanced AGM LAB improves about 25 %. At 0 oC CA (Charge Acceptance), the initial charging current of the advanced AGM LAB increases about 25 %. Improving the bonding between the grid and A.M. by roughening the grid surface improves the flow of current and lowers the resistance, which is considered to have a significant effect on the high current charging/discharging area. In a Standard of Battery Association of Japan (SBA) S0101 test, after 300 A discharge, the voltage of the advanced AGM LAB with the Sand-Blasting method grid was 0.059 V higher than that of untreated grid. As the cycle progresses, the gap widens to 0.13 V at the point of 10,800 cycles. As the bonding between grid and A.M. increases through the Sand Blasting method, the slope of the discharge voltage declines gradually as the cycle progresses, showing excellent battery life characteristics. It is believed that system will exhibit excellent characteristics in the vehicle environment of the ISG system, in which charge/discharge occurs over a short time.

3 mol% yttria-doped stabilized zirconia (3YSZ) is synthesized by a solvothermal process, and its characteristics are investigated using various methods. Also, the dispersibility of synthesized 3YSZ nanoparticles is observed with the species of surface modifier. The 3YSZ nano sol prepared with an optimum condition is employed in prism coating and its properties are evaluated. The synthesized 3YSZ nanoparticles show a globular shape with about 10 to 20 nm crystallite size. The mixed phases with the nano sol show a high specific surface of 178 m2/g. The prism sheet coated with the 3YSZ nano sol present an excellent refractive index, transmittance, and luminance; refractive index is 1.603, transmittance is 90.2 %, and luminance of coating film is improved by 5.9 % compared to that of the film without 3YSZ nano sol. It is verified that the surface modified 3YSZ is suitable as the prism sheet for optical displays.

CeO2 nanoparticles, employed in a lot of fields due to their excellent oxidation and reduction properties, are synthesized through a solvothermal process, and a high specific surface area is shown by controlling, among various process parameters in the solvothermal process, the type of solvent. The synthesized CeO2 nanoparticles are about 11~13 nm in the crystallite size and their specific surface area is about 65.38~84.65 m2/g, depending on the amount of ethanol contained in the solvent for the solvothermal process; all synthesized CeO2 nanoparticles shows a fluorite structure. The dispersibility and microstructure of the synthesized CeO2 nanoparticles are investigated according to the species of dispersant and the pH value of the solution; an improvement in dispersibility is shown with the addition of dispersants and control of the pH. Various dispersing properties appear according to the dispersant species and pH in the solution with the synthesized CeO2 nanoparticles, indicating that improved dispersing properties in the synthesized CeO2 nanoparticles can be secured by applying dispersant and pH control simultaneously.

동물원은 야생동물이 대중에게 전시용으로 사육되는 곳이다. 동물원의 역할과 기능은 교육, 연구, 정서적 효과·레저 오락, 자연 보호종 보존이다. 이 연구는 국내동물원의 환경풍부화 현황에 대해 알아보고 향후 방향성 제시하는 것을 목표로 하였다. 우리는 정형행동을 보이는 동물들의 환경은 열악할 것이라고 예상하였다. 연구방법은 런던동물원 협회에서 제시한 Animal Welfare Assessment Process (AWAP)를 참고하여 국내동물원 중 J동물원과 S동물원을 대상으로 환경풍부화에 관한 복지 수준을 평가하였다. 8개의 세부항목으로 이루어져 있고, 아시아코끼리, 미어캣, 표범, 반달가슴곰, 호랑이, 늑대, 다람쥐원숭이를 복지 수준 평가동물로 선정하였다. J동물원의 늑대와 반달가슴곰의 환경은 자연환경과 유사하게 조성되었지만, 나머지 동물들의 환경은 열악하였다. S동물원의 환경은 대체적으로 좋았으나 표범의 사육장의 크기는 다른 동물들에 비해 넓지 않았다. 우리의 가설과 대부분 일치하였지만, 환경이 잘 되어있어도 정형행동을 보이는 경우도 있었다. 따라서 사람 기준이 아닌 동물 기준에서 자연생태계와 최대한 비슷한 환경으로 조성해야 함을 제시한다.

NiAl2O4 nanoparticle was synthesized by a reverse micelle processing for inorganic pigment. N (NO3)2·6H2O and Al(NO3)3·9H2O were used for the precursor in order to synthesize NiAl2O4 nanoparticles. The aqueous solution, which consisted of a mixing molar ratio of Ni/Al, was 1:2 and heat treated at 800~1100 oC for 2h. The average size and distribution of synthesized NiAl2O4 powders are in the range of 10-20 nm and narrow, respectively. The average size of the synthesized NiAl2O4 powders increased with an increasing water-to-surfactant molar ratio and heating temperature. The crystallinity of synthesized NiAl2O4 powder increased with an increasing heating temperature. The synthesized NiAl2O4 powders were characterized by X-ray diffraction analysis(XRD), a field emission scanning electron microscop (FE-SEM), and a color spectrophotometer. The properties of synthesized powders were affected as a function such as a molar ratio and heating temperature. Results indicate that synthesis using a reverse miclle processing is a favorable process to obtain NiAl2O4 spinels at low temperatures. The procedure performed suggests that this new synthesis route for producing these oxides has the advantage of being fast and simple. Colorimetric coordinates indicate that the pigments obtained exhibit blue colors.

Inorganic pigments have high thermal stability and chemical resistance at high temperature. For these reasons, they are used in clay, paints, plastic, polymers, colored glass and ceramics. CoAl2O4 nano-powder was synthesized by reverse-micelle processing the mixed precursor(consisting of Co(NO3)2 and Al(NO3)3). The CoAl2O4 was prepared by mixing an aqueous solution at a Co:Al molar ratio of 1:2. The average particle size, and the particle-size distribution, of the powders synthesized by heat treatment (at 900; 1,000; 1,100; and 1,200˚C for 2h) were in the range of 10-20 nm and narrow, respectively. The average size of the synthesized nano-particles increased with increasing water-to-surfactant molar ratio. The synthesized CoAl2O4 powders were characterized by X-ray diffraction analysis(XRD), field-emission scanning electron microscopy(FE-SEM) and color spectrophotometry. The intensity of X-ray diffraction of the synthesized CoAl2O4 powder, increased with increasing heating temperature. As the heating temperature increased, crystal-size of the synthesized powder particles increased. As the R-value(water/surfactant) and heating temperature increased, the color of the inorganic pigments changed from dark blue-green to cerulean blue.

The corrosion resistance of submerged entry nozzle (SEN) materials were investigated for high-class steel manufacturing. Composite samples were fabricated by mixing ZrO2, Al2O3, MgO, mullite, spinel, and carbon. The raw materials were mixed with attrition milling, compacted in a uniaxial pressure of 200MPa and calcined at 1000˚C for 3 h in N2 atmosphere. The bulk density and apparent porosity of the calcined samples were measured by the liquid displacement method in water using Archimedes's principle. The corrosion resistance of the samples were measured by cup test with mold powder at 1550˚C for 2 h. The microstructure and elemental analysis of samples were observed by scanning electron microscopy (SEM), energy dispersive spectrum (EDS), and X-ray diffraction pattern (XRD). The XRD result shows that the starting raw materials were crystalline phase. The microstructure of fabricated specimen was investigated before and after corrosion tests at 1000˚C and 1550˚C for 2h. ZrO2-C composite showed good resistance in the slag corrosion test. Among the composite oxide materials, ZrO2-Al2O3-C and ZrO2-MgO-C showed better resistance than ZrO2-C in the slag corrosion test. The diameter variation index of ZrO2-C refractory was 16.1 at 1000˚C for 2 h. The diameter variation index of the ZrO2-Al2O3-C refractory was larger than that of the ZrO2-C refractory at 1550˚C for 2 h.

마편초과의 좀목형 엽에 함유된 물질의 allelopathy 효과를 구명하기 위해 수용성 엽 추출액, 메탄올 엽 추출액, 엽 분말과 토양과의 혼화된 pot에 각각 상치, 이탈이란라이그라스, 개솔새, 억새 종자를 발아실험하여 발아억제물질을 분석한 결과는다음과 같다. 1. 좀목형 엽 분말을 증류수에 각각 24, 48, 72 시간 침지 후 추출물에 상치, 이탈리안라이그라스, 개솔개, 억새 종자를 파종한 후의 발아율은 각 처리구마다 대조구마다 높은 발아억제를 보였고, 48시간 침지시에는 각각 26.9%, 58.8%, 6.6%, 22.2%의 발아율을 보여 강한 발아억제현상르 보였다. 2. 좀목형 엽 분말을 메탄올 75%에 24, 48시간 침지 후 추출물에 이탈리아라이그사스, 개솔새, 억새 종자를 파종한 후의 발아율은 48시간 추출액때 각각 33.3%, 15.4%, 7.7%를 보여 48시간 수용성 추출액과 24시간 메탄올 추출액보다 강한 발아억제효과가 있었다. 3. 좀목형 엽 분말과 Vermiculite를 1: 99.5: 95, 10:90, 20:80(w/w)으로 구분한 pot에 공시수종을 파종한 결과 엽 분말의 비율이 높을수록 발아억제효과가 컸으며, 엽 분말이 20%인 경우 발아된 부분의 건중량의 비율은 실험구와 대조구간에 비교한 발아율의 비율보다 훨씬 낮아 생장억제효과가 있는 것으로 나타났다. 4. Column chromatography의 TLC를 이용하여 최종 7 fraction을 찾고 생물검정 결과, 5, 6번 fraction에 강한 활성을 나타냈다. 5. UV 와 IR분광분석 결과 UV 분광분석은 256 nm과 336nm에서 흡수 최대를 나타내었으며, 이들은 시르시트시약을 사용하여 검토한 결과 7위에 에테르 결합한 전형적인 플라본류로 추정되었고, IR 분광분석 결과 지방족에 에테르결합이 존재하는 것으로 생각되었다. 6. Py-GC-MS 분석으로부터 5, 6 fraction의 경우 플라본류에 1개의 당이 결합한 배당체 구조이고 B환의 경우 1개 또는 2개 이상의 페놀성 수산기의 존재가 예상되었다.

이 논문에서는 초기 지중응력(initial ground stress)으로 인한 수직터널의 균열 발생여부를 확인하기 위해 수압파쇄시험을 실시하였다. 수압파쇄시험 결과 터널 내 발생된 균열은 초기 지중응력과의 직접적인 연관성이 낮음을 확인하였다.

In this study various investigations were carried out to analyze the causes of leakage for 20 years on the slope of the downstream side of the dam during the ○○ dam precision safety diagnosis. Analysis showed that the possibility of underground water flowing through the valley section of the mountain area extremely low, and that direct leakage of the reservoir's freshwater was confirmed as the main leakage path.

Most of the domestic jetties of jacket structure were designed by SACS with design criteria based on “Design Standards for Harbour and Fishery Port”. In fact, companies of structural maintenance and Inspection fail to conduct proper safety assessment of jetties of jacket structure using SACS due to a manpower shortage. But instead, they are using MIDAS to conduct safety assessment of these jetties as an alternative to using SACS. The purpose of this study is to provide the rational way for MIDAS user to assess jetties of jacket structure using SACS.

There are many cracks in Section Change. We investigated surface and geological environment and so on. To figure out the cause of cracks, we are using FEM. This Study can help developing designation and maintenance about Tunnel.