본 논문은 한국 언론에서 보도하고 있는 중국 이미지가 한․중 관계의 변화에 따 라 어떻게 변화하고 있는지, 그리고 통상 보수 또는 진보 언론으로 구분되는 언론사 별로 중국 관련 보도에 유의미한 차이점이 있는지를 분석하였다. 분석 방법으로 빅 카인즈(BigKinds)를 활용하여 1990년부터 2022년까지 중국 관련 사회·문화면 뉴스 기사에 대해 의미연결망 분석과 감성분석을 활용하였다. 분석 결과 언론에서 보도되 는 중국 이미지는 양국 관계에 따라 변하고 있었다. 또한 감성분석 결과 전체 기간 동안 긍정 단어가 부정 단어보다 많았으나 2016년 이후 긍정 단어는 감소하고 있었 다. 2018년 이후 최근 5년 동안 보수 언론은 진보 언론보다 높은 부정적인 감성 강 도를 보이고 있었다.

원전 구조물의 실시간 모니터링 기술이 요구되고 있지만, 현재 운영 중인 지진 감시계통으로는 동특성 추출 등 시스템 식별이 제한 된다. 전역적인 거동 데이터 및 동특성 추출을 위해서는 다수의 센서를 최적 배치하여야 한다. 최적 센서배치 연구는 많이 진행되어 왔 지만 주로 토목, 기계 구조물이 대상이었으며 원전 구조물 대상으로 수행된 연구는 없었다. 원전 구조물은 미미한 신호대잡음비에도 강건한 신호를 획득하여야 하며, 모드 기여도가 저차 모드에 집중되어 있어 모드별 잡음 영향을 고려해야 하는 등 구조물 특성을 고려 해야 한다. 이에 본 연구에서는 잡음에 대한 강건도와 모드별 영향을 평가할 수 있는 최적 센서배치 방법론을 제시하였다. 활용한 지표 로서 auto MAC(Modal Assurance Criterion), cross MAC, 노드별 모드형상 분포를 분석하였으며, 잡음에 대한 강건도 평가의 적합성을 수치해석으로 검증하였다.

This paper reports the results of an experimental examination using X-rays to test annealing materials for lapped bearing steel (STB2), to confirm the validity of the weighted averaging analysis method. The distribution behavior for the sin diagram and the presence or absence of differences in the peak method, half-value breadth method, and centroid method were investigated. When lapping the annealed bearing steel (STB2) material, a residual stress state with a non-directional steep gradient appeared in the surface layer, and it was found that the weighted averaging analysis method was effective. If there is a steep stress gradient, the sin diagram is curved and the diffraction intensity distribution curve becomes asymmetric, resulting in a difference between the peak method, half-value breadth method, and centroid method. This phenomenon was evident when the stress gradient was more than 2~3 kg/mm2/μm. In this case, if the position of the diffraction line is determined using the centroid method and the weighted averaging analysis method is applied, the stress value on the surface and the stress gradient under the surface can be obtained more accurately. When the stress gradient becomes a problem, since the curvature of the sin diagram appears clearly in the region of sin > 0.5, it is necessary to increase the inclination angle  as much as possible. In the case of a lapping layer, a more accurate value can be obtained by considering  in the weighted averaging analysis method. In an isotropic biaxial residual stress state, the presence or absence of  can be determined as the presence or absence of strain for sin≈0.4.

The most comprehensive and particularly reliable method for non-destructively measuring the residual stress of the surface layer of metals is the sin method. When X-rays were used the relationship of sin measured on the surface layer of the processing metal did not show linearity when the sin method was used. In this case, since the effective penetration depth changes according to the changing direction of the incident X-ray,  becomes a sin function. Since  cannot be used as a constant, the relationship in sin cannot be linear. Therefore, in this paper, the orthogonal function method according to Warren’s diffraction theory and the basic profile of normal distribution were synthesized, and the X-ray diffraction profile was calculated and reviewed when there was a linear strain (stress) gradient on the surface. When there is a strain gradient, the X-ray diffraction profile becomes asymmetric, and as a result, the peak position, the position of half-maximum, and the centroid position show different values. The difference between the peak position and the centroid position appeared more clearly as the strain (stress) gradient became larger, and the basic profile width was smaller. The weighted average strain enables stress analysis when there is a strain (stress) gradient, based on the strain value corresponding to the centroid position of the diffracted X-rays. At the 1/5 max height of X-ray diffraction, the position where the diffracted X-ray is divided into two by drawing a straight line parallel to the background, corresponds approximately to the centroid position.

Magnesium alloy is the lightest practical metal. It has excellent specific strength and recyclability as well as abundant reserves, and is expected to be a next-generation structural metal material following aluminum alloy. This paper investigated the possibility of thin plate fabrication by applying a overheating treatment to the melt drag method, and investigating the surface shape of the thin plate, grain size, grain size distribution, and Vickers hardness. When the overheating treatment was applied to magnesium alloy, the grains were refined, so it is expected that further refinement of grains can be realized if the overheating treatment is applied to the melt drag method. By applying overheating treatment, it was possible to fabricate a thin plate of magnesium alloy using the melt drag method, and a microstructure with a minimum grain size of around 12 μm was obtained. As the overheating treatment temperature increased, void defects increased on the roll surface of the thin plate, and holding time had no effect on the surface shape of the thin plate. The fabricated thin plate showed uniform grain size distribution. When the holding times were 0 and 30 min, the grain size was refined, and the effect of the holding time became smaller as the overheating treatment temperature increased. As the overheating temperature becomes higher, the grain size becomes finer, and the finer the grain size is, the higher the Vickers hardness.

Research is being actively conducted on the continuous thin plate casting method, which is used to manufacture magnesium alloy plate for plastic processing. This study applied a heat transfer solidification analysis method to the melt drag process. The heat transfer coefficient between the molten magnesium alloy metal and the roll in the thin plate manufacturing process using the melt drag method has not been clearly established until now, and the results were used to determine the temperature change. The estimated heat transfer coefficient for a roll speed of 30 m/min was 1.33 × 105 W/m2·K, which was very large compared to the heat transfer coefficient used in the solidification analysis of general aluminum castings. The heat transfer coefficient between the molten metal and the roll estimated in the range of the roll speed of 5 to 90 m/min was 1.42 × 105 to 8.95 × 104 W/m2·K. The cooling rate was calculated using a method based on the results of deriving the temperature change of the molten metal and the roll, using the estimated heat transfer coefficient. The DAS was estimated from the relationship between the cooling rate and DAS, and compared with the experimental value. When the magnesium alloy is manufactured by the melt drag method, the cooling rate of the thin plate is in the range of about 1.4 × 103 to 1.0 × 104 K/s.

AZ31 magnesium alloy was used to manufacture a thin plate using a melt drag method. The effects of roll speed, molten metal temperature, and molten metal height, which are the basic factors of the melt drag method, on the surface shape, the thickness of the thin plate, Vickers hardness, and microstructure of the thin plate were investigated. It was possible to manufacture AZ31 magnesium alloy thin plate at the roll speed range of 1 to 90 m/min. The thickness of the thin plate, manufactured while changing only the roll speed, was about 1.8 to 8.8 mm. The shape of the solidified roll surface was affected by two conditions, the roll speed and the molten metal height, and the Vickers hardness of the manufactured magnesium alloy thin plate value ranged from Hv38~Hv60. The microstructure of the thin plate produced by this process was an equiaxed crystal and showed a uniform grain size distribution. The grain size was greatly affected by the contact state between the molten metal and the solidification roll, and the amount of reactive solids and liquids scraped at the same time as the thin plate. The average grain size of the thin plate fabricated in the range of these experimental conditions changed to about 50-300 μm.

본 논문은 반도체, 디스플레이, 디지털 가전 및 휴대폰 등을 포괄하는 중국 전자산 업을 대상으로 OECD TiVA 데이터베이스를 활용하여 2000년~2018년까지의 중국 수 출을 부가가치 기준으로 분해하여 분석하였다. 분석 결과 중국 전자산업은 총 수출 액과 부가가치 수출액 모두 세계 1위로, 2018년 기준 중국 총수출의 약 30%를 차지 하고 있었다. 국내부가가치(DVA) 측면에서 중국은 해외 부품 조달을 통해 조립․가 공한 후 수출하는 비교적 저부가가치 활동을 담당하는 중간단계에 머무르고 있는 것 이 아니라 자국 부품 조달 및 국내 생산 비중을 높여 부가가치를 높인 것으로 분석 되었다. 주요국(한국, 대만, 미국, 일본)과의 비교에서 중국 전자산업의 국내부가가치 비중은 미국, 일본 다음으로 높은 비중을 차지하고 있었고 부가가치 기준 현시비교 우위지수(VRCA)도 높은 수준으로 상승하고 있었다.

In this study, the shrinkage at the artificial skin tissue and temperature characteristics of rubber pole were analyzed by the experimental and numerical method. A artificial skin tissue was produced by using the rigid sponge pad. The impact of tissue was applied by three types of rubber pole. The shrinkage results along the depth of tissue were measured according to the repetition count of impact. When the shape of rubber pole was sphere type, the shrinkage was greatest. The temperature around the pole was highest in the sphere type while that inside pole was greatest in the twine deep sphere type. This is because the pole temperature of twine deep sphere type was transmitted more inside. As a result, the sphere type rubber pole was the most effective because it showed the largest shrinkage and the lowest temperature gradient during impact.

Using the data of patents granted by USPTO during 2013~2017 from WIPO IP Statistic Data Center, this paper examines the general trend and the main technical fields of international patents granted to Korea, China and Japan. The Patent Activity Index(PAI) was used to analyze the dynamic changes of international patents in the top 5 technical fields. The results show as follows. First, the number of international patent applications and registration by China has been increasing rapidly in recent years. Second, the technical fields of international patents granted by China and South Korea are mainly concentrated in several fields, such as computer technology, semiconductors, digital communication, audio-visual technology and electrical machinery, apparatus, energy. Third, through the PAI index analysis, the technology innovation and concentration of South Korea and China surpassed Japan in telecommunications technology field, and China’s development in the semiconductor field is the strongest. The technological innovation performance of Japan was analyzed as to be relatively higher than that of China and South Korea in the field of electrical machinery, apparatus, energy.

In this study, the characteristics of muscle relaxation were analyzed by the experimental and numerical method. A skin tissue was produced by imitational biological tissue using the agar powder, saline solution and sugar. The tissue was exposed to three types of wavelength-blue visible radiation(410 nm), red visible radiation(635 nm), and infrared ray(830 nm). The temperature results along the depth of tissue were measured according to the variation of light wavelength and irradiation time. The temperature change of the tissue shown up similar pattern regardless of the light wavelength kinds. The wavelength of infrared ray penetrated strongly into tissue between 3.2 mm and 11.4 mm. Also, the temperature change with the irradiation time was small, and the temperature value of the infrared ray was the largest. As a result, the muscle relaxation will occur mainly at the infrared wavelength.

In this paper, the performance of the Refrigerator is improved by controlling the fan speed on the condenser side or subcooling/superheating degree by superimposing the refrigerant on the inlet side of the compressor to the outlet side pipe. However, these methods may have the effect of lowering the performance due to operation of the severe condition of the main parts and may not achieve the intended performance. The Peltier Module was used to improve the performance of the refrigerator and increase the durability of the main parts through an artificial subcooling device.

최근의 제조 산업에서 제품개발 정보는 제품 수명주기 관리(PLM: Product Lifecycle Management) 시스템을 통하여 관리하고, 조달과 생산 계획에 관련된 통제는 전사적 자원관리(ERP: Enterprise Resource Planning), 생산 관리 시스템이 담당하고 있다. 특히, 효율적인 제품 개발과 시스템 구축 여부는 설계 및 생산, 원가 관리 전체에 걸쳐 영향을 미친다. 따라서 도면, 모델, 자재 정보 등 제품정보관리를 위한 PLM시스템의 역할이 매우 중요하게 여겨지고 있다. 이러한 PLM체계는 요구 사항 분석, 시스템 설계 그리고 기존 Data Migration 등 정보 시스템 개발 절차를 따라서 수행된다. PLM시스템은 전사적인 시스템 개발 과정에서 Prototype개발을 진행하여 구축 절차와 체계 설계를 검증하는 것이 효과적이다. 이 과정에서 PLM 아키텍처 및 제품 구조(Product Structure) 구성, PLM의 기능 개발을 수행한 후에 전체 시스템 설계 개발을 재 수행하는 것이 효과적이다. 본 연구에서는 조선 PLM구축에 필요한 절차와 체계 설계 방법을 제시하고, 이를 초기 기본 설계 단계에 적용하여 PLM구축 방법론을 제시하고자 한다. 초기 설계를 대상으로 요구사항을 도출하고, PLM의 아키텍처를 설계하였으며, 설계한 시스템을 Prototype형태로 제시하였다.

지하터널은 그 경계가 반무한영역에서 설정되고 재료나 형상의 복잡성을 갖고 있기 때문에, 동적하중에 대하여 정확한 거동을 해석하기 위해서는 3차원 동적해석이 필요하다. 이때 일반적인 수치해석기법인 유한요소만을 이용한 방법은 인위적 경계에서의 파의 반사, 입력자료의 방대함 등으로 인하여 효율적이지 못하게 된다. 본 연구는 이러한 점을 고려하여 지하터널에 직접 가해지는 동적하중에 대한 효율적인 해석기법을 개발하는데 그 목적이 있다. 개발된 프로그램에서 지반의 반무한성은 3차원 경계요소로 고려되었으며, 구조물에는 3차원 동적해석을 수행한 결과 기존의 2차원 터널해석에서 고려가 곤란했던 차량의 진행하중으로 인한 반복효과가 합리적으로 반영되는 것으로 분석되었다.

본 연구는 콘크리트 내부 공극 및 계면 사이에 깊게 침투가 가능한 실란복합화합물을 기반으로한 표면보호재 (Silane Surface Protection Material, SSPM)를 사용한 기존 콘크리트 내구성 향상 방안 도출을 위해 실시되었다. SSPM을 적용한 모르타르의 미세구조 평가, 잔골재의 입도 분포에 따른 침투깊이 및 공극량을 측정하였다. 그 결과 모르타르 내부에 액상 및 크림형질의 SSPM이 침투된 것으로 나타났으며, 공극량 평가결과 잔골재의 입도분포에 관계없이 SSPM을 적용하였을 때 공극량이 감소하는 것으로 나타났다. 침투깊이 평가결과 잔골재의 입도분포에 관계없이 SSPM 도포량이 증가함에 따라 침투깊이가 증가하는 것으로 나타났으며, 공극량이 상대적으로 많은 일반잔골재(Type 2)로 제작한 모르타르의 침투깊이가 적게 나타났다. 콘크리트에 적용할 경우 침투깊이는 다소 감소할 것으로 판단되나, 콘크리트 표면에 침투하여 내구성을 향상 시길 수 있을 것으로 판단된다.

This study was evaluated the penetration performance according to SPM type. The types of SPM are liquid and cream type. And the amounts of SPM were applied 0.13, 0.25, 0.36, and 0.51 kg/㎡. The specimen size was 100×30mm as KS F 4930. Test results indicated that the penetration depth of SPM were improved with increasing the amounts of application of liquid and cream SPM. In the case of applied cream SPM of 0.13, 0.25 and 0.36 kg/㎡ the standard deviation of penetration depth was less the liquid type SPM was applied.

We know that the failure of high performance concrete pavement occurs in the aspects of its structure, environment, material, and construction. We have been able to identify the reason why no construction should be permitted when average daily temperature is below 4 degree celsius. We must pay careful attention to the curing management and comply with the standards of concrete production and construction.