본 연구에서는 차량과 교각의 직접충돌해석을 통하여 기존 설계기준(도로교설계기준, AASHOTO LRFD)에서 아직 고려하고 있지 않은 동적영향을 고려한 실제 교각의 충돌 파괴 거동을 다양한 경계조건별로 검토하였다. 선정된 차량은 10톤, 16톤, 38톤의 Cargo 트럭이며 교각은 경부고속도로 상 일반적인 제원으로 선정하였다. 해석결과 가장 많은 파괴는 상부구조의 고려없이 교각의 상부면을 구속하였을 시에 발생하였으며 상부구조는 2차적인 영향을 교각에 전달하기 보다는 충돌에너지를 일부 흡수하는 역할을 하며 파괴를 감소시키는 것으로 확인되었다. 또한 해석의 효율성을 위해 차량과 강체간 충돌시 발생하는 충돌하중이력곡선을 교각에 외력으로 부여한 간접충돌해석을 수행하고, 이를 직접충돌해석 결과와 비교하였다. 해석결과 직접충돌해석 결과와 매우 유사하게 교각의 거동을 예측하는 것으로 확인되었으며 해석효율성 또한 높아져 해석시간은 약 92%정도 감소하였다. 이러한 간접충돌해석법은 다양한 기존 모델이나 다른 해석프로그램에도 쉽게 부여될 수 있어 그 활용범위가 증가할 것으로 판단된다.

본 연구에서는 프리스트레스트 콘크리트 일방향 슬래브의 사용성 평가를 위한 처짐을 분석하기 위하여 유한요소법에 기반한 해석적 연구를 수행하였다. 유한요소 상용 프로그램을 이용한 해석결과와 실험결과를 비교하여 모델링의 타당성을 검증하였으며, 비교적 유사한 결과를 나타내었다. 또한, 콘크리트 압축강도, 편심 거리, 활하중, 그리고 긴장재의 배치형태에 따른 처짐을 분석하여 수계산 결과와 비교하였고, 회귀분석을 통해 변수들과 처짐 사이의 상관관계를 확인하였다. 그 결과, 콘크리트 압축강도가 클수록, 편심 거리가 클수록, 활하중이 작을수록 처짐이 감소하는 것을 확인하였으며, 직선형태의 처짐이 가장 작고 절곡형태의 처짐이 가장 큰 것을 확인하였다. 또한 회귀분석을 통해 콘크리트 압축강도와 편심 거리가 솟음값에 미치는 영향을 분석하였다.

이 논문에서는 곡선 프리스트레스트 콘크리트 사장교의 풍하중에 의한 정적 횡방향 휨거동 해석에 비선형 해석 모델 특성들이 미치는 영향을 검토하여 곡선 프리스트레스트 콘크리트 사장교의 풍하중에 의한 정적 휨거동을 정당하게 예측할 수 있는 해석방법을 제시하였다. 곡선 프리스트레스트 콘크리트(PSC) 사장교의 시공단계별 풍하중에 의한 횡방향 휨거동 해석 시 재료의 비선형성은 물론 기하학적 비선형성을 모두 고려하였고 재료의 시간의존적 특성의 영향으로 콘크리트의 크리프, 건조수축, 강도증가와 프리스트레싱(PS) 강재와 케이블의 이완을 고려하였다. 곡선 PSC 사장교의 풍하중에 의한 휨거동을 다양한 비선형 해석 모델 특성들을 조합해서 고려하여 해석을 수행한 결과, 교량 상판의 인장균열 및 이에 따른 처짐의 증가를 정확히 예측하기 위해서는 재료의 비선형 응력-변형률 관계는 물론 콘크리트의 인장균열을 모두 포함한 재료 비선형성과 기하강성도 매트릭스는 물론 대변위에 의한 변형률의 비선형항 및 부재의 위상변화를 모두 포함하는 기하학적 비선형성을 고려한 해석이 반드시 필요함을 확인하였다. 부가적으로, 콘크리트의 인장증강효과 및 뼈대요소의 축력에 의한 기하강성도 매트릭스의 고려여부는 교량의 풍하중에 의한 정적 휨거동을 예측하는 데 영향을 크게 미치지 않는 것으로 나타났다. 또한 풍하중에 의한 곡선 PSC 사장교의 횡방향 휨거동은 상판의 횡방향 변위의 상당한 증가 및 거더 단면의 인장균열로 인해 상판이 폐합되기 직전단계가 폐합된 이후 단계보다 크게 불리함을 확인하였다.

PURPOSES: The objective of this study is to evaluate the tack-coating material’s properties using the bitumen bond strength(BBS) test and damping test as function of changed curing times. In this study, bonding strength tests were performed according to the curing time of tack coating materials. METHODS : In order to investigate bonding characteristic of tack coating materials, the Pneumatic Adhesion tensile Testing Instrument(PATTI) device is used to measure the bond strength between the tack coating materials and aggregate substrate based on the AASHTO TP-91. Also, damping test as in situ test was used to determine an appropriate traffic openting time for construction vehicle. Four different tack-coating materials were used in this study. The BBS tests were performed a one hour curing and testing temperatures of 5℃, 15℃, and 25℃. Damping test was conducted at 30min, 60min, 90min, and 120 min of curing times with temperatures of 20℃ and 30℃. RESULTS and CONCLUSIONS : The BBS test results show various bond strength as function of tack coat materials. At the same testing condition, A tack coat material shows almost two times higher than D tack coat materials although both materials are satisfied the criteria of material’s physical properties. Also, Dampting test results shows similar trend with BBS test result. The damping test result was significantly changed as function of tack coat materials. Based on this study, the tack coating material’s curing time is very important. Therefore, both curing time and the bond strength’s characteristic has to be considered in standard specification.

PURPOSES: The purpose of this study is to evaluate the degree of restraint (DOR) of longitudinal steel at continuously reinforced concrete pavement (CRCP) against environmental loadings. METHODS : To measure the longitudinal steel strain, 3-electrical resistance and self-temperature compensation gauges were installed to CRCP test section (thickness = 250mm, steel ratio = 0.7%) and continuously measured 10 min. intervals during 259 days. In order to properly analyze the steel strains first, temperature compensation process has been conducted. Secondly, measured steel strains were divided into 12 phases with different events such as before paving, during concrete hardening, and after first cracking, etc. RESULTS : Thermal strain rate (TSR) concept is defined as the linear strain variations with temperature changes and restraints rate of longitudinal steel against environmental loadings (especially thermal loading) with different cases is defined as degree of restraint(DOR). New concept of DOR could be indirect indicator of crack width behaviors of CRCP. CONCLUSIONS: Before paving, DOR of longitudinal steel is almost same at the coefficient of thermal expansion of steel (12.44m/m/℃) because of no restraint boundary condition. After concrete pouring, DOR is gradually changed into -1 due to concrete stiffness developing with hydration. After first cracking at crack induced area, values of DOR are around -3~-5. The negative DOR stands for the crack width behavior instead of steel strain behavior. During winter season, DOR reached to -5.77 as the highest, but spring this values gradually reduced as -1.7 as the lowest. Based on this observation, we can presume crack width decreased over time within the time frame of this study. This finding is not consistent with the current theory on crack width variations over time, so further study is necessary to identify the causes of crack width reducing. One of the reasons could be related to concrete stress re-distribution and stress relaxation.

PURPOSES : In this study, wasted vinyl aggregate, which possesses better thermal properties than natural aggregate, was used in cement concrete mixture to develop more economical concrete with thermal insulation and freeze prevention effects. METHODS : Slump and air content of the fresh concrete, which substituted its 0%, 5%, and 10% of coarse aggregate with wasted vinyl aggregate, were measured. Compressive strength, Poisson’s ratio, elastic modulus, and splitting tensile strength of hardened concrete were measured by laboratory tests. Thermal properties of concrete such as coefficient of thermal expansion, thermal conductivity, and specific heat were also measured according to replacement ratio of wasted vinyl aggregate. Finally, the thermal insulation and freeze prevention effectiveness of the concrete mixed with wasted vinyl aggregate was confirmed through finite element analysis of road pavement crossing above concrete box culvert made from wasted vinyl aggregate. RESULTS: Even though the physical properties of wasted-vinyl-aggregate concrete such as compressive strength, Poisson°Øs ratio, elastic modulus, and splitting tensile strength were inferior to those of ordinary concrete, they met requirements for structural concrete. The thermal properties of concrete were improved by wasted vinyl aggregate because it decreased thermal conductivity and increased specific heat of the concrete. According to the result of finite element analysis, temperature variation in pavement subgrade was mitigated by box culvert made from wasted-vinyl-aggregate concrete. CONCLUSIONS: Through the laboratory test and finite element analysis of this study, it was concluded that the concrete structures made from wasted vinyl aggregate showed thermal insulation and freeze prevention effects.

PURPOSES: The purpose of this paper is showing that the state of pavement sublayers can be evaluated differently according to direction of FWD. METHODS: The concrete pavement slabs above subgrade without anything, subgrade with cavity, and box culvert were modeled by finite element method(FEM). The modeled pavements were analyzed by changing the direction of falling weight deflectometer(FWD). The deflection results obtained from FEM were used to calculate radius of relative stiffness and composite modulus of subgrade reaction using AREA method. Then, the analyzed results were compared to the results of the test performed at the Korea Expressway Corporation(KEC) test road. RESULTS : The composite modulus of subgrade reaction increased with subgrade elastic modulus, while radius of relative stiffness decreased. The pavement sections of pure earth showed the consistent results regardless of FWD direction. In case there was cavity, the radius of relative stiffness was larger and composite modulus of subgrade reaction was smaller when FWD was leaving the cavity than when approaching the cavity. This pattern became clear when the cavity got larger. In case of the section with box culvert, the pattern was opposite to the case of cavity. When the soil cover depth increased, the effect of box culvert got smaller. When the load was applied far from the cavity and box culvert, the effect was also declined. The test performed at the KEC test road showed identical results to those of finite element analysis. CONCLUSIONS : The direction of FWD should be considered in evaluation of the state of pavement sublayers because it can be evaluated differently even under identical condition.

PURPOSES : The purpose of this study is to analyse the longitudinal steel strain and stress of continuously reinforced concrete pavement(CRCP) with longitudinal and transverse direction at early age using stress dependent strain analysis method. METHODS : To measure the longitudinal steel strain, 9-electrical resistance and self-temperature compensation gauges were installed to CRCP test section (thickness = 250mm, steel ratio = 0.7%) and continuously measured 10min. intervals during 30days. In order to properly analyze the steel stress first, temperature compensation process has been conducted. Secondly, measured steel strains were divided into stress dependent strain (elastic strain) and stress independent strain (thermal strain) and then stress dependent strain was applied to stress calculation of longitudinal steels. RESULTS: Steel strains were successfully measured during 30days. To verify the accuracy of temperature compensation process, measured coefficient of thermal expansion(COTE,11.46×10-6m/m/℃) of longitudinal steel before paving was compared with that of unrestrained steel. Max. steel stress in the transverse direction shows about 266MPa at 23days after placement. CONCLUSIONS: Steel stresses in the longitudinal and transverse direction have been evaluated. In longitudinal direction, steel stress from the crack was rapidly reduced from 183MPa at crack to 18MPa from 600mm apart the crack. From this observation, stress effective length can be identified as within 600mm apart from the crack. In transverse direction, max. stress point was located near the center of pavement width and stress level(266MPa) is about 66% of yield stress of steel

PURPOSES: The purpose of this study is to verify the causes of surface scaling at L-shoulder concrete structure. METHODS : From the literature reviews, mechanisms of frost damage were studied and material properties including strength, air void, spacing factor and scaling resistance of L-shoulder concrete structure were analyzed using core specimens taken by real fields. RESULTS : The spacing factor of air void has relatively high correlation of surface conditions : lower spacing factor at good surfacing condition and vice versa. If the compressive strength is high, even thought spacing factor does not reach the threshold value of reasonable durability, the surface scaling resistance shows higher value. Based on these test results, the compressive strength also provide positive effect on the surface scaling resistance. CONCLUSIONS: The main causes of surface scaling of L-shoulder could be summarized as unsuitable aid void amount and poor quality of air void structure. Secondly, although the compressive strength is not the governing factor of durability, but it shows the positive effect on the surface scaling resistance.

PURPOSES: Analysis and design of asphalt concrete (AC) and continuously reinforced concrete (CRC) composite pavements. METHODS: In this study, the service life of the AC/CRC composite pavements was determined based on the probabilistic method in the mechanistic-empirical pavement design guide(MEPDG). Typical pavement design was provided with respect to heavy truck traffic volume of highways. RESULTS: The service life of the composite pavements based on IRI was shorter than that based on rutting at lower traffic volume, but this trend was switched at higher traffic volume. CONCLUSIONS : It is concluded that the main distress affecting the service life of the composite pavements was longitudinal roughness and rutting. Roughness became lower, but rut depth became greater as the stiffness of the CRC increased.

본 논문은 철근콘크리트 구조물의 지진해석에 관한 국제 벤치마크 프로젝트인 SMART-2013을 통해 3차원 비대칭 철근콘크리트 건물의 고유진동수와 재료 비선형성을 고려한 지진응답을 계산한 결과를 제시한다. 이를 위해 콘크리트와 철근의 비선형 재료모델을 구성하고 대표부피요소에 대한 국부테스트를 수행하여 비선형 모델의 성능을 평가하였다. 이러한 SMART-2013 철근콘크리트 건물의 비선형 유한요소모델에 대해 모드해석과 저강도 지진하중에 대한 선형 시간이력해석을 수행한 결과, 구조물의 고유진동수, 변위 및 가속도 시간이력이 SMART-2013 프로젝트에서 제시한 실험값들과 유사하였다. 또한 Northridge 지진에 대한 변위 및 가속도 응답의 시간이력과 최대층간상대변위의 응답스펙트럼을 계산하여 고강도 지진 하중에 대한 이 철근콘크리트 건물의 거동을 평가하였다.

이 연구에서는 물량저감 철근상세를 갖는 중공 철근콘크리트 교각 시스템의 전용 설계프로그램과 소성설계 적용 결과를 제시하였다. 개발된 물량저감 철근상세는 경제성과 합리성을 갖으며 공사기간의 단축을 가져올 수 있다. 물량저감 중공 철근콘크리트 교각의 적용을 통해 경제성 평가를 수행하였다. 평가 결과 개발상세가 기존상세에 비해 구조적 합리성, 시공성, 그리고 경제성 등이 우수함을 확인하였다.

PURPOSES : The purpose of this article is to compare and evaluate the riding comfort of a passenger in tunnels depending on different surface textures of concrete pavement. METHODS: Evaluation of riding comfort is conducted at 17 sections, which have different surface texture such as transverse tinned(TT), longitudinal tinned(LT) and diamond grinded(DG). A triaxial accelerometer was set up on the passenger seat surface of the test vehicle to measure vibrations of an occupant, then the effects of vibration on comfort and health were evaluated by ISO 2631. And microphones were installed at passenger's ears height to measure sound pressure level(SPL) in the test vehicle. Additionally, a surface microphone was installed on the inside of wheel arch to evaluate noise between tire and pavement by NCPX method. All tests were conducted cruising at 100km/h. RESULTS : The results of all tests are as follows. First, both vibration magnitudes for comfort and for health in LT and DG sections are almost same and they represent lower than those in TT sections. Second, the average SPL of DG shows the lowest decibels among them. And third, it is founded that interior noise is significantly affected by noise between tire and pavement. CONCLUSIONS : It may be concluded that DG can provide more excellent riding comfort to passenger than LT or TT. Therefore, it is necessary to consider applying DG to existing pavement surface to improve surface condition when the driving environment especially requires riding comfort like a long tunnel.

PURPOSES: In areas of high traffic volume, such as expressway across large cities, the amount of nitrogen oxides (NOx) emitted into the atmosphere as air pollution can be significant since NOx gases are the major cause of smog and acid rain. Recently, the importance of NOx removal has arisen in the world. Titanium dioxide (TiO2), that is one of photocatalytic reaction material, is very efficient for removing NOx. The NOx removing mechanism of TiO2 is the reaction of solar photocatalysis. Therefore, TiO2 in road structure concrete need to be contacted with ultraviolet rays (UV) to be activated. In general, TiO2 concretes are produced by replacement of TiO2 as a part of concrete binder. However, considerable portion of TiO2 in concrete cannot contact with the pollutant in the air and UV. Therefore, TiO2 penetration method using the surface penetration agents is attempted as an alternative in order to locate TiO2 to the surface of concrete structure. METHODS: This study aimed to evaluate the NOx removal efficiency of photocatalytic concrete due to various TiO2 application method such as mix with TiO2, surface spray(TiO2 penetration method) on hardened concrete and fresh concrete using surface penetration agents. The NOx removal efficiency of TiO2 concrete was confirmed by NOx Analyzing System based on the specification of ISO 22197-1. RESULTS: The NOx removal efficiency of mix with TiO2 increased from 11 to 25% with increasing of replacement ratio from 3 to 7%. In case of surface spray on hardened concrete, the NOx removal efficiency was about 50% due to application amount of TiO2 with surface penetration agents as 300, 500 and 700g/m2. The NOx removal efficiency of surface spray on fresh concrete due to all experimental conditions, on the other hand, which was very low within 10%. CONCLUSIONS: It was known that the TiO2 penetration method as surface spray on hardened concrete was a good alternative in order to remove the NOx gases for concrete road structures.

현재 청정에너지 확보에 대한 기술은 전 세계적으로 큰 관심을 가지고 있다. 이에 대한 접근법 중 가장 주목을 받고 있는 것은 에너지 하베스팅 기술이다. 에너지 하베스팅은 기존 구조물에서 낭비되어 지는 풍 력, 태양광·열과 같은 에너지를 전기에너지 및 열에너지로 변환하여 사용할 수 있도록 하는 기술이다. 그 중 온도 차이에 의해 전기를 생산 할 수 있는 발전소자를 이용하여 콘크리트 포장도로에 적용하고자 한다. 콘크리트 포장도로의 표면은 하루 중 가장 태양열에 오랜 시간 노출되는 구조물 중 하나이며, 그로 인하여 콘크리트 구조물의 상부와 하부의 온도차이가 발생하게 된다. 본 실험에서는 발전소자의 콘크리트 적용의 효율증대를 위해 알루미늄 판을 부착시킨 상태와 부착시키지 않은 상태의 동일 시간대의 전압생성 량을 비교하여 동일한 실험조건(온도, 측정시간, 공시체크기)을 유지한 상태에서 실험해 보았다.

일상생활에서 사용되고 있는 도자기는 점토 등을 원료로 사용하여 제조되며 이를 제조하는 공장이나 사용하는 가정에서 버려지고 폐기처분되는 폐기물량은 공장에서만 연간 6천여톤으로 보고되고 있으며 가 정에서 버려지는 생활도자기를 합산하면 상당량이 폐기물로 처리 되는 것으로 추산된다. 이처럼 폐기 처 리되는 도자기는 주로 매립되어지거나 일부 제한적으로 골재를 대체하여 사용되는 것으로 보고되고 있다. 이러한 폐도자기는『건설폐기물 재활용 촉진에 관한 법률 시행령, 시행규칙』이 개정되면서 건설폐기물로 폐기처리됨으로서 처분이 용이하게 되었으며 환경보전 및 자원재활용 측면에서 적극적인 재활용 방안이 모색되어야 할 것으로 사료된다. 따라서 본 연구에서는 도자기 폐기물을 효율적으로 재활용하는 방안으로 폐도자기를 미분말화하여 대기온도가 낮은 초봄이나 늦가을 초기강도 발현이 요구되며, 초기균열 방지와 알칼리골재반응이 방지되는 콘크리트 도로포장에 활용성을 검토하고자 하였다. 기존의 연구된 자료에 의하면 이화영 등(2008, 2010)은 폐도자기분말의 혼입에 따른 시멘트 모르타르의 특성, 시멘트 혼합재로 활용하기 위한 폐도자기분말의 연구, 폐도자기 분말의 PHC 파일에 시멘트 혼합재 로서 적용성 검토 등을 수행하였다. 이 연구에 의하면 국내에서 수급된 폐도자기의 화학적 특성을 분석한 결과는 표 1과 같으며 주요 화학적 조성성분은 SiO2성분이 65%, Al2O3와 CaO가 각각 19% 및 5.66%인 것 으로 분석되었다. 또한 폐도자기분말을 시멘트 혼화재료로 사용할 경우 작업성의 개선, 시멘트의 절감효 과, 초기강도개선 효과를 나타내는 것으로 연구되었으며, 혼화재료로서의 성능은 고로슬래그를 사용한 것 보다 우수한 것으로 연구되었다. 뿐만아니라 제반 품질규정이 만족되고 제조원가 절감 등 자원재활용적인 측면에서 효용가치가 있는 것으로 연구되어 콘크리트나 모르터르에 활용 가능성을 확인하였다.