In this study, an experimental analysis of noise reduction in road traffic by applying the Micro Grooving technique to concrete highway pavements is explored. Initiated in 1984 to address the aging and damage issues observed in South Korea's concrete highways, Micro Grooving is known for creating fine grooves on the cement pavement surface to increase friction, prevent hydroplaning, and inhibit ice formation, while reducing vehicle friction noise by 3∼5dB(A). It is determined from noise measurement results that the application of the Micro Grooving method can be expected to reduce roadside noise and enhance the safety of drivers' driving experience.

Internal combustion engine is the main source of environmental pollutants and therefore advanced technology is required to reduce harmful elements from the exhaust gases all over the world. Especially, when the exhaust gas is released from the automotive muffler, exhaust noise has many bad influence on the surrounding environment. In order to reduce the exhaust noise, it is necessary that automotive muffler must be designed for best exhaust efficiency. The sound insulation room was installed for the analysis of an acoustics characteristics of the noise from automotive muffler, in this study. Exhaust gas noise, noise distribution characteristics, pressure and temperature of exhaust gas were investigated with the change of annulus temperature of air cooled annulus automotive muffler and cooled annulus automotive muffler. The following results were obtained with this study. From the frequency analysis of automotive muffler, high noise distribution was observed in the range 100~2000Hz. It means that the noise in this range has an dominate influence for the overall noise. Noise reduction of automotive muffler was affected by the temperature of annulus. It is caused the result that the high temperature and pressure of exhaust gas are changed lower by the drop of annulus temperature. The tendencies of noise, the temperature and pressure of exhaust gas are similar to the performance curve of engine. Exhaust gas pressure is determined by the r.p.m. of engine and affected by the cooling performance of automotive muffler.

In the case of the companies selected for noise measurement in this study, even though noise exposure in the workplace begins with noise management for large machines or high-output machines, they only manage to write reports on how much workers are exposed to noise for 8 hours a day. is focused on. When large machines are delivered, little information on noise received from the manufacturer is kept, and noise information indicated on design drawings is also difficult to find. History management of noise information of large machines is necessary. There is also a problem with the professionalism of managers who manage noise information. Like odors and fine dust, it is judged that noise needs to be managed by a professional manager at the workplace and managed through a database of noise information.

In this study, the abnormal noise phenomenon generated intermittently in the shock absorber of the combat armored vehicle was approached from the side of the squeak joint to solve the phenomenon. In order to identify the cause of the noise, the factors causing friction in the shock absorber were checked from the viewpoint of problem product analysis, process, and design. As an improvement plan, by improving the non-lubricated section in the nitrogen chamber, the operating noise was reduced to a level lower than that of a general automobile engine along with the elimination of noise. Considering that this is a combat vehicle, it is judged that it has been improved so as not to affect the survivability and health of the crew during equipment operation. Through the improvement of this study, it is expected to prevent power loss and improve the emotional quality of our soldier.

선내 소음은 선원의 거주성과 건강을 위한 중요한 요소 중의 하나로, 선내 소음을 줄이기 위한 노력이 활발하게 진행되고 있 다. 소음 저감 방법에는 수동소음제어(PNC) 방법과 능동소음제어(ANC) 방법이 있다. 자동차, 항공기와 달리 선박에서는 ANC를 이용한 소음 저감 대책이 미미한 실정이다. 본 연구는 능동소음제어(ANC)와 같이 방음판과 고주파진동원을 이용하여 기관실에 발생한 소음을 줄이고자 하였다. 이를 위해 아크릴 상자를 이용하여 실험 모형을 만들었고, 4가지 조건별로 소음 저감 효과를 측정하였다. 실험 결과는 다음과 같다. 첫째, 방음판은 55 dB ~ 85 dB까지 모든 범위에서 소음 저감 효과가 있었다. 고주파진동원은 낮은 소음에서 효과가 없었으나, 70.8 dB(A)과 85 dB(A)와 같은 높은 소음에서는 효과가 있었다. 둘째, 방음판과 고주파진동원을 동시에 사용하는 경우에는 최대 -2.2 dB(A) 만큼의 소음 저감 효과가 있었다. 본 실험의 결과는 아크릴판으로 제작한 실험모형에서 얻은 결과로 철판으로 된 실제 선박과 다를 수 있 다. 추후 연구에서 실제 선박에서 사용하는 철판(재질과 두께, 구조를 고려)을 이용하여 실험하고자 한다. 이 연구가 선박에 승선하는 선 원들의 거주성 향상과 건강 증진에 도움이 되기를 기대한다.

소음공해는 인간과 해양환경에 악영향을 끼치며, 선박과 해양구조물에서 발생하는 유동소음을 예측을 통해 소음에 대한 안전 성을 평가하고 해양환경을 보존할 수 있다. 기존 수중구조 유동소음 해석기법은 전산유체역학과 FW-H음향상사식을 이용한 하이브리드법 기반이다. FW-H는 무한공간에서의 음향전파를 가정하여 소음해석을 수행하기 때문에 음파의 반사와 산란, 회절의 영향이 나타나는 근접 장 해석이 제한적이다. 반면 격자볼츠만기법 기반의 직접법 유동소음해석을 수행하면 근접장 음향효과를 소음해석에 반영할 수 있다. 직 접법 해석은 유동과 소음이 연성된 해석이 수행되고 구조경계에서의 반사와 회절, 유동에 의한 매질 불균일성에 따른 산란효과가 반영된 다. 그간 격자볼츠만기법이 수중조건에서 수치적으로 불안정하여 수중환경에 적용이 불가능했다. 하지만 수중환경에서 사용할 수 있는 DM-TS 격자볼츠만기법 충돌연산자가 개발되어 수중으로 확장이 가능해졌다. 본 연구에서는 파이프내 원형구멍에 대하여 격자볼츠만기 법 해석을 수행해 수중 유동소음해석이 가능함을 보였다. 격자볼츠만기법 해석을 통해 도출한 유동과 소음을 각각 실험과 비교하여 해석 의 신뢰도를 확보하였다. 파이프내 유동소음에 의한 주요 압력 피크가 해석에 반영되었으며 이를 통해 격자볼츠만기법을 이용한 근접장 유동소음해석이 가능함을 확인했다.

Aircraft noise is something humans don't want. In this study, based on the Rotax 914 engine used in Korea, the propeller blade angle was changed by 1 degree and the engine RPM was changed to review the three-wing “G Company” propeller and the three-wing GSC wooden propeller. Select the best propeller pitch angle by measuring the change in propeller noise and thrust and the change in engine RPM due to the change in noise and thrust. We would like to present a propeller pitch angle suitable for the location of the airfield and the operation of the aircraft. Based on this, we would like to help resolve noise complaints around the airfiled.

Noise is a sound that people don't want. In this study, noise is measured for SR20, a general aviation trainer used in Korea. In addition, noise measurement points are selected at Muan Airport, where most of the domestic trainers fly under the supervision of the Ministry of Land, Infrastructure and Transport, and the measured data are analyzed based on this. We also want to analyze the noise characteristics of SR20 aircraft through frequency analysis of the noise characteristics of SR20 aircraft are unique. We want to use this to understand what type of noise the trainer affects in future studies. this study will improve the reliability of the noise prediction scenario by comparing and analyzing the actual measured and predicted values when using the noise prediction program.

The noise of large and high-power machines was evaluated and the establishment of mitigation measures was studied. The noise level of large machinery and high-power machinery installed at domestic plant sites was investigated and compared with the noise disclosure regulations to see if they met the standards of the Occupational Safety and Health Act. This investigated the soundproofing design of large and high-power machines and the soundproofing design of complex noise of large machines installed in the plant, and prepared the design standards of the plant design company. In the future, we will compile a database of data to secure standards for research and plant design related to noise reduction, and propose noise improvement and management measures for large and high-power machines.

Metal material production process machinery is becoming larger due to the development of industry. Since there are many overseas manufacturers of large machines used in industrial fields, there are limitations in investigating the manufacturer's noise prediction method and measurement method. A noise map was prepared to obtain information necessary for noise reduction and to effectively manage noise companies. It was modeled with the drawings provided to prepare the noise map and the results of the actual measurement of the site. In order to improve the noise environment of workers, there was a noise reduction effect when a soundproof wall was installed between the noise source and the worker's workplace.

There is a considerable amount of research on metal material product worker’s hearing loss caused by noise that comes from manufacturing process. A further investigation that characterizes the sound that comes from manufacturing process of metal material products. however. To do this, a noise management plan is needed. It should include a generated sound process from the main sources of disturbance at manufacturing process areas. And a soundproof measurement will identify the amount of noise reduction needed for a hearing-safe working environment. Finally, researchers in this study measured tests on the noise and the vibration process, and the noise caused by operations allowed for an investigation on the suitability of certain environmental conditions. Noise-related programs can be used to predict the noise distribution of the noise level characteristic. This can help identify and reduce the presence of sound interference through sound proofing measures.

Most domestic pilots are trained at local airfields using propeller aircraft. Training aircraft are mainly trained in the airspace around the aerodrome, and mainly take-off and landing exercises that require a lot of practice among flight control skills. Aircraft noise is a sound that humans do not want. In this study, based on the Rotax 914 engine used in Korea, the propeller blade angle was changed by 1 degree for the 3-leaf “K company” propeller and the 3-leaf GSC wooden propeller, and the engine RPM was changed to examine the noise and thrust changes. The purpose of this study is to check whether noise and thrust loss are the least at the engine's maximum RPM, and to propose an aircraft operation plan in the noisy aerodrome area based on the values.

Environmental noise occurring on ships has various negative impacts on sailors’ health conditions such as hearing loss, sleep disturbance, psychological stress, etc., so regulations on them are required, but the ship noise regulations are usually applied to only large merchant ships. Although regulations on fishing boats with strong fishing and work intensity are determined to be necessary, there has been little relevant research. This study, therefore, attempted to measure the environmental noise of coastal composite fishing vessels less than two tones and provide the results of basic research on the noise regulations for fishing vessels. It measured them by setting the measurement zones as after side, midship and fore side, and based on the criterion of IMO MSC 337(91). The findings showed that the noise of them often exceeded 75dB(A), the criterion of the open deck noise in the zones in which the load of main engines was increased. In particular, the noise of the stern was as high as 92.2dB(A) during the full ahead. Hence, hearing loss may be caused by such a noise, so a variety of regulations on it are determined to be necessary.

Noise is a sound that humans do not want. In this study, noise is measured for C172, the most frequently used general aviation trainer in Korea and abroad. In addition, in this study, noise measurement points are selected for Muan Airport, where most of the domestic training aircraft fly under the supervision of the Ministry of Land, Infrastructure and Transport. Based on this, the measured data is scaled and analyzed. In addition, we intend to analyze what characteristics C172 aircraft have unique through frequency analysis of noise of C172. Through this, it is intended to understand what type of noise training aircraft affect in future studies.