In this study, the shear strength according to the width of the web was assessed by using the Waste styrofoam as hollow material without reprocessing. The concrete's design strength was set to 24MPa and the web width was 50mm, 100mm, and 150mm as variables. Shear strengths of KCI increased from 111.2% to 203.9%.

High-rise buildings in recent years are increasing demand for high strength. However, the higher the floor, the greater the weight of the building, resulting in structural problems. In this study, the shear span ratio was equal to 1.5, and the effect of the web width (100 mm, 150 mm) on the shear strength of I-type flexural members was evaluated.

Effect of confining pressure on the shear strength of ultra-high-performance fiber-reinforced concrete (UHPFRCs) was investigated using a new shear test setup. Different confining pressures were applied and maintained to the specimens prior to shear testing. The shear strength of UHPFRCs was obviously sensitive to the confining pressure: the higher confining pressure produced higher shear strength. The confined shear strength could be expressed as a function of unconfined shear strength, confining pressure, and tensile strength.

The paper presents a comparison of available shear strength models of RC columns by considering the effect of axial force. Although various shear strength models are proposed by many researchers, some of them neglect the effect of axial force. Thus, to clarify the effect of axial force on shear strength, the comparative study is conducted with a total of 54 experimental data of RC column collected from the PEER center. The shear strength of RC column is also evaluated with design code.

In this paper, the shear performance of the deep beams with high strength headed reinforcement was evaluated. The experimental parameters are horizontal stiffener and fusing length. The shear span-depth ratio (a/d) of specimens was 1. The development length of headed reinforcement was evaluated to have a great influence on the shear strength of the deep beam.

The shear strength of damaged reinforced concrete beams using externally post-tensioning steel rods increased by 25∼57% compared to control beam. ACI 318-14 (simpled and detailed approaches) specifications for prestressed concrete beams conservatively predicted the nominal shear strength

The steel grid composite deck is a composite structure made of a concrete slab disposed over a steel grid. In this study, the punching shear strength obtained experimentally and the shear strength calculated by design equations of ACI 318 and Eurocode 2 are compared. The result shows that the experimental strength is best estimated by the design equation of Eurocode 2 which considers reinforcement ratio.

This paper is for to propose the shear strength equation by using results of former researchers like as Lubell et al.(2008) and Kim et al.(2016). Support width was chosen as the variables and experiment was conducted. Proposed equation was estimated accurately and safely rather than Lubell’s proposal.

The purpose of this study is to establish a reasonable analytical method for the estimation of overall behavior characteristic from cracking to yielding of rebar and crushing of concrete and seismic performance of reinforced concrete shear wall with high-strength reinforcing bar. A total of 8 specimens of reinforced concrete walls which have constant aspect ratio and a variety of variables such as reinforcement ratio, reinforcement yielding strength, reinforcement details, concrete design strength, section shape and whether lateral restraint hoop were selected and the analysis was performed by using a non-linear finite element analysis program (RCAHEST) applying the proposed constitutive equation by the authors. The mean and coefficient of variation for maximum load from the experiment and analysis results was predicted 1.04 and 8%. The mean and coefficient of variation for displacement corresponding maximum load from the experiment and analysis results was predicted 1.17 and 19% respectively. The analytical results were predicted relatively well the fracture mode and the overall behavior until fracture for all specimens. These results are expected to be used as basic data for application of high-strength reinforcing bar to design codes in the future.

The shear strength of damaged reinforced concrete beams using externally post-tensioning steel rods increased by 25∼57% compared to control beam. ACI 318-14 (simpled and detailed approaches) specifications for prestressed concrete beams conservatively predicted the nominal shear strength.

The goal of this experimental works is to evaluate the influence of shear strength according to shear span to depth ratio of RC deep beam with high-strength hooked bars. A total of 3 specimens were constructed and tested in three-point bending up to failure. The test variables included the shear span to depth ratio (0.75, 1.0, 1.25). Specimens had a failure mode of shear fracture. For specimen with shorter shear span to depth ratio, it showed that maximum shear strength was higher and that more brittle behavior occurred.

This paper is about experimental works to evaluate the effects of fiber reinforcement to shear behavior of RC deep beams with high strength hooked bars. It was planned two specimens with different shear span-to-depth ratio. Specimen had three loading points to induce shear failure. From test results, it showed that maximum shear strength of specimen with shorter shear span to depth ratio was higher.

데크플레이트 철판을 성형하여 구성한 DH-Beam은 형틀 역할 뿐 아니라 합성거동에 기여할 것으로 판단되며, 본 연구에서는 DH 측판의 전단강도 기여도를 평가하고자 하였다. 총 5개의 실험체를 대상으로 실험 및 해석적 연구를 수행하였다. 실험체는 2개의 정가력 실험 체, 2개의 부가력 실험체, 그리고 1개의 RC 실험체로 구성되었다. RC 실험체는 DH-Beam과 비교를 목적으로 제작하였다. DH-Beam에 대한 실 험결과는 전단강도를 산정하는 설계식 그리고 RC 실험체에 대한 실험결과 등과 비교하였으며, 그 결과 DH-Beam의 측판은 전단강도에 기여 하고 있다. 비선형 구조해석에서는 실험체를 대상으로 DH 판의 기여도를 평가하였다. 구조해석에서는 DH 측판 만 있는 경우 혹은 DH 판이 전 혀 없는 경우 등 다양한 경우를 대상으로 하였다. 구조실험 및 해석적 연구의 결과 DH-Beam의 측판은 콘크리트와 합성단면을 형성하면서 전 단강도에 기여하는 것으로 평가할 수 있다.

본 연구는 고강도 섬유보강 시멘트 복합체(UHSCC) 접착성능을 평가하는 것이 목적이다. Direct shear test를 통해 압축전단접착강 도를 측정한 결과 NC(보통강도콘크리트)+ NC 실험체(150×150×150)에서는 모든 수준에서 유사한 압축전당접착강도를 나타내었고, 반 면 UHSCC+UHSCC에서는 지연타설 30분 후부터 0분에 비해 압축전단접착강도가 낮아지는 것을 확인할 수 있었다. 이를 통한 접착면의 파괴 모드를 분석한 결과 NC+NC 에서는 모든 수준에서 비계면 파괴를 보였고 UHSCC+UHSCC에서는 30분, 60분, 90분 시험체에서 계면파괴가 일 어났다. NC 및 UHSCC의 타설면을 XRD 시험을 통해 분석한 결과 NC 시험체에 비해 UHSCC의 시험체 에서 많은량의 SiO2의 성분이 검출되 는 것을 알 수 있었고 UHSCC에서 나타난 코팅막의 주성분의 대부분은 SiO2로 사료된다. 따라서 본 연구에서 사용된 UHSCC는 지연타설 30분 후 부터는 접착성능의 저하로 구조체로서의 사용이 어렵다고 판단된다. 금후 연구에서는 콜드조인트 발생 부위의 면처리 방법을 통한 접착성 능 향상이 필요하다고 사료된다.

본 연구는 철근콘크리트 기둥과 철골보로 이루어진 RCS합성구조에서 내부접합부의 전단강도에 관한 연구이다. 새로운 건물 구조시스템인 합성구조 시스템은 철근콘크리트 기둥과 철골보의 장점을 최대한 살린 구조로서 경제적, 실용적인 접합부 상세들이 많이 개발되어 왔다. 그럼에도 불구하고 접합부에 대한 구조적 거동 및 응력전달기구가 명확히 밝혀지지 않고 있으며 여전히 제안된 식들로부터 많은 차이를 보이고 있다. 따라서 본 연구에서는 접합부에서 철골보가 철근콘크리트 기둥을 관통하는 보 관통형 RCS 구조체를 대상으로 하여 기존의 전단파괴 실험체 37개를 접합부 형태에 따라 기존에 제안된 5개의 주요식들에 적용하였다. 회기분석을 통한 각 제안식의 신뢰성을 검증하였고, 기존식들의 단점을 보완할 수 있는 전단강도 추정식을 제안하였다.

Ultra high strength concrete was introduced into architectural members. The current ultra high strength concrete can achieve compressive strengths up to 200 MPa and tensile strengths up to 20 MPa. In this study, the flexural and shear strengths in precast structural beams using ultra high strength concrete are evaluated and compared with reinforced concrete beams. This paper also provide a design flexural strength formula for the developed members.

This study reviews past literatures relevant to concrete beams using recycled aggregates (RAs) and investigate existing shear design equations for reinforced concrete (RC) beams. Then, a simplified, emprical design equation to determine the shear strength of high strength RC beams with RAs is proposed and compared with existing equations. The analysis indicated that the proposed equation provided the most accurate estimated of strength of high strength concrete beams with RAs.

In this study, the shear buckling strengths of the trapezoidal and sinusoidal corrugated plates with the same self-load were compared, and their characteristics and tendencies were analyzed. In the preceding comparative study of corrugation shapes, the corrugation wave depth and the corrugation wave angle were the same. As these target, A linear buckling analysis was conducted, and the differences in the shear buckling mode and the buckling stress were analyzed.

In this paper, the RC column-based joint connection part carry out loading test by reinforced hollow or extended Base Plate in order to confirm that RC joint punching shear reinforcement effect of applying the Base Plate. Base Plate thickness, extension length, size, and type as the variable, Base Plate suitable for the stress distribution and shape and dimensions confirmed through experiment and then reinforcing effect was analyzed. Experimentally, vertical load transmitted to the Base Plate from column to foundation is effective to stress distribution and then, type of hollow reinforcement more efficient than a closed. Through experiment, improve performance and ductility due to reinforcement and relative to the thickness of the existing foundation reduced even showed better performance than the existing. The behavior of the reinforced specimens be able to induce from brittle to ductile. Experiment on loading to destroy performed the pattern of cracks, destruction aspect before and after reinforcement.

In case of Enlargement method using Post-installed Anchors, mechanical expansion anchors were resisting tensile and shear force of Modular extension structure in exist building. The purpose of this study is to investigate strength of Post-installed Anchor on 16 MPa low strength Concrete under less than standard effective depth(hef). The fracture pattern of the specimens in Pull-out tests was pull-out failure and concrete break out failure. In monotonic load shear tests the fracture pattern was steel failure of anchor and concrete break out failure.