This study was conducted to research how UCD(Ultra Constant Discharge) lamp lighting affects plant cultivation. To get the results within a short time, lettuce seedling was selected as a plant and nutrient hydroponic beds were used in a dark room for 100% artificial lighting. Two beds were installed for same distance lighting condition with UCD lamp and Hi-pressure Sodium lamp each and another two beds were installed for same light intensity condition with each type of lamp. After 15 days of cultivation, for both conditions, the yields under UCD lamp were weighed more than that under Hi-pressure Sodium lamp. The result can be analyzed that the spectrum of UCD lamp having near sunlight characteristic is much superior to that of Hi-pressure Sodium lamp having a line spectrum characteristic on yellow and red wavelengths for plant cultivation.

HI몰랄리티가 9.5 mol/kg-H2O인 HI의 전해-전기투석을 시판의 양이온교환막(CMB)을 이용하여 요오드의 존재하에 실험을 진행하였다. 수소이온 투과의 선택성을 증가시키기 위해, 막은 전자선 가속기를 이용하여 방사선 처리하였다. 방사선 처리한 막의 막특성(막 저항, 이온교환용량, 함수율)을 측정하였다. 각각의 방사선량에서 처리한 막의 2 mol/dm3의 KCl 용액에서 막저항, 이온교환용량과 함수율은 처리하지 않은 막과 거의 동등의 값을 가졌다. HI몰랄리티가 9.5 mol/kg-H2O인 HI의 전해-전투기투석을 75℃, 9.6 A/dm2에서 진행하였다. 전자선 가속기에 의해 방사선 처리한 양이온교환막은 처리하지 않은 막과 비교하여 고분자의 가교구조와 함께 수소이온투과의 높은 선택성을 가졌다.

The influence of Hi-flux powders characteristics on the performance of magnetic powder cores was studied. It was found that different cooling rate and nozzle configuration could change the shape and microstructure of powders. Smooth surface and spherical shape of powders were beneficial to improve DC bias performance and reduce core losses of magnetic powder core.

In order to investigate the effects of magnetized water treated with HI-Scalper153R on body performance and ammonia concentration in feces of broiler chicks, a feeding trial was conducted with a total of 180 broiler chicks. Each treatment had 18 chicks with 5 replications. Chicks during experimental periods, broiler chicks were fed magnetized water and subterranean water, respectively. The results obtained summarized as follows: Body weight gain slightly increased for broiler chicks fed magnetized water compared with control. But, there is no significantly (p=0.36) different among treatments. Feed intake significantly (p=0.046) decreased for broiler chicks fed magnetized water compared with control. Feed efficiency was significantly (p=0.020) improved for broiler chicks fed magnetized water of each periods when compare to the control. Especially, in starter periods, the feed efficiency of magnetized water treatment increased by 10% more than control (1.80 vs 1.69). In feces, average ammonia concentration (ppm) significantly (p=0.004) decreased in the magnetized water treatment compare to control. Especially, the magnetized water treatment decreased by 2.2 times compared to the control in ammonia concentration of feces (83 vs 37ppm).

열화학적 IS 공정에서 요오드화수소의 분해에 적용하기 위하여 화학증착법(CVD)으로 제조된 silica 막의 안정성을 HI-H_2O 기상 혼합물에서 평가하였다. Si 원천으로 tetraethoxysilane을 사용하여 서로 다른 CVD 온도로 기공크기가 100 nm인 α-alumina를 처리하였다. CVD온도는 700^℃, 650^℃, 600^℃이었다. 600^℃에서 수행한 단일 성분의 투과 실험에서 측정한 막의 H_2/N_2 선택도는 CVD 온도 700^℃의 M1 막은 43.2, 650^℃의 M2 막은 12.6, 600^℃의 M3 막은 8.7을 나타내었다. HI-H_2O 기상 혼합물에서 안정성 실험은 450^℃에서 수행하였는데, CVD 온도 650^℃에서 처리된 막이 다른 온도에서 처리된 막보다 더 안정성이 더 좋은 결과를 얻었다.

We have searched for HI 21 cm line emission from shocked atomic gas associated with southern supernova remnants (SNRs) using data from the Southern Galactic Plane Survey. Among the 97 sources studied, we have detected 10 SNRs with high-velocity HI emission confined to the SNR. The large velocity and the spatial confinement suggest that the emission is likely from the gas accelerated by the SN blast wave. We also detected 22 SNRs which show HI emission significantly brighter than the surrounding regions over a wide (>10 km s-1) velocity interval. The association with these SNRs is less certain. We present the parameters and maps of the excess emission in these SNRs. We discuss in some detail the ten individual SNRs with associated high-velocity HI emission.

Powder forging with a back pressure was investigated for production of automobile and compressor parts made of a rapidly solidified Al-Si alloy powder. Disk-shaped green compacts made of a rapidly solidified Al-Si alloy powder were hot forged, and hubs were formed by loading back pressure on their top. The influences of the back pressure and die temperatures on forgeabiliy and properties of parts made of a rapidly solidified Al-Si alloy powder were examined. This method was also applied to the production of a scroll part. The results of these studies are summarized as follows : 1. A back pressure on the hub top is very effective for consolidation and preventing crack formation in the hub. 2. When a back pressure tess than 98 MPa is applied, the forging pressure increases by the same amount of the applied back pressure. With more than 98 MPa, the forging pressure increases further due to an increased friction at the hub side. 3. Die temperatures higher than approximately 670k are needed in order to consolidate well the hub top without cracks.