In gamma-ray spectrometry for volume samples, the self-attenuation effect should be considered in the case of differences in chemical composition and density between the efficiency calibration source for quantitative analysis of sample and the sample actually measured. In particular, the lower the gamma-ray energy, the greater the gamma-ray attenuation due to the self-attenuation effect of the sample. So, the attenuation effect of low-energy gamma-rays in the sample should be corrected to avoid over- or under-estimation of its radioactivity. One of the most important factors in correcting the self-attenuation effect of the sample is the linear attenuation coefficient for the sample, which can be directly calculated using a collimator. The larger the size of the collimator, the more advantageous it is to calculate the linear attenuation coefficient of the sample, but excessive size may limit the use of the collimator in a typical environmental laboratory due to its heavy weight. Therefore, it is necessary to optimize the collimator size and structure according to the measurement environment and purpose. This study is to optimize a collimator that can determine the effective linear attenuation coefficient of low-energy gamma-rays, and verify its applicability. The overall structure of the designed collimator was optimized for gamma-ray energy of less than 100 keV and cylindrical plastic bottle with diameter of 60 mm and a height of 40 mm. The materials of optimized collimator consisted of tungsten. Acryl and acetal were used to form the housing of the collimator, which fixes the central axis of the bottle, collimator and point-like source. In addition, using the housing, the height of the tungsten is adjusted according to the height of the sample. For applicability evaluation of the optimized collimator, IAEA reference material in solid form were used. The sample was filled in the bottle with heights of 1, 2, 3 and 4 cm respectively. Using the collimator and point-like source of 210Pb (46.5 keV), 241Am (59.5 keV), and 57Co (121.1 keV), the linear attenuation coefficient and the radioactivity for the samples were calculated. As a result, to calculate the linear attenuation coefficient using the optimized collimator, a relatively high sample height is required. However, the optimized collimator can be used to determine the linear attenuation coefficients of low-energy gamma-rays for the self-attenuation correction regardless of the sample height. It is concluded that the optimized collimator can be useful to correct the sample selfattenuation effect.

Lightweight steel is a crucial material that is being actively studied because of increased carbon emissions, tightening regulations regarding fuel efficiency, and the emergence of UAM, all of which have been recently labeled as global issues. Hence, new strategies concerning the thickness and size reduction of steel are required. In this study, we manufacture lightweight steel of the Fe-Mn-Al-C system, which has been recently studied using the DED process. By using 2.8 wt.% low-Mn lightweight steel, we attempt to solve the challenge of joining steel parts with a large amount of Mn. Among the various process variables, the laser scan power is set at 600 and 800W, and the laser scan speed is fixed at 16.67 mm/s before the experiments. Several pores and cracks are observed under both conditions, and negligibly small pores of approximately 0.5 μm are observed.

Background: Low back and neck pain are two of the most common medical problems in the adult population. It is estimated that between 70% and 80% adults experience an episode of low back pain at least once during their lifetime. Objects: This study aimed to compare the effects of various stretching exercises and muscle energy techniques used for treatment of iliopsoas, quadratus lumborum, and hamstrings of patients with low back pain. Methods: A total of 52 subjects were randomly assigned to the control group (n = 17), the muscle energy technology group (METG, n = 19), and the stretching exercise group (SEG, n = 16). Interventions were performed twice a week for 4 weeks. Outcomes were measured before and after 4 weeks of treatment in the three groups, using the Korean version of the Oswestry Disability Index, the Visual Analogue Scale (VAS), the Fear Avoidance Belief Questionnaire (FABQ), the Finger to Floor test (FTF), the Modified-Modified Schober Test (MMS), and the Trunk Flexion Range of Motion test. Results: This study showed significant reduction in the pre-test and post-test KODI, VAS, and FABQ scores in all the three groups (p < 0.05). The KODI, VAS, FABQ and FTF assessed in this study showed interactions between the groups and the measurement time point (p < 0.01). After intervention, the KODI, VAS, FABQ and FTF in the SEG and METG were significantly higher (p < 0.05), and there was no difference between the METG and SEG. MMS and HFROM test showed no difference between the three groups (p > 0.05). Conclusion: KODI, VAS, FABQ and FTF showed significant improvement after basic physical therapy, muscle energy technique, and stretching exercise intervention. And there was no significant difference in the intervention effect between the muscle energy group and the stretching exercise group.

Background: Lower back pain (LBP) is a major cause of disability and a common musculoskeletal disorder encountered at some point in life. Dysfunction of the lumbar vertebrae has been associated with decreased flexibility of the hamstrings, which exhibited a strong positive correlation with LBP. Hamstring tension affects lumbar pelvic rhythm. We aimed to activate pelvic stability with compression by Active Therapeutic Movement (ATM), muscle energy technique (MET) was applied to increase the flexibility of the hamstring. Objects: In this study, we aimed to investigate the effects of MET with ATM and general MET were applied to the hamstring of adults, who were in their twenties with nor without LBP, on their pelvic inclination and the length of their hamstring. Methods: A total of 32 subjects were briefed about the purpose of this study and agreed to participate voluntarily. Before the experiment, all subjects were pre-examined, and they were divided into an LBP group and a no lower back pain group accordingly. Thereafter, all subjects participated in both in a crossover manner. After at least one week, they switched to another group and participated in the same experiment. Results: The study results revealed that both groups demonstrated significant results in the modified active knee extension test (p < 0.01) and the sit and reach test (p < 0.01) performed to assess the hamstring flexibility; an interaction (p < 0.05) was noted. Moreover, a more significant difference was observed between the MET with ATM and the general MET. Although significant results were obtained for the pelvic inclination (p < 0.01), interaction was not noted. Conclusion: Conclusively, in this study, when the MET with ATM was applied to the two groups, there was a significant difference compared to the general MET for hamstring flexibility, but it was confirmed that there was no significant difference for the pelvic inclination.

정삼투 공정(forward osmosis, FO)은 역삼투 공정(reverse osmosis, RO)에 비해 저압으로 운영되므로 오염 제어, 유지 보수, 막 세정 및 잠재적 에너지 저감 측면에서 큰 이점이 있어 다양한 분야에 적용할 수 있는 기술이다. 특히, 정삼투 공정의 막오염층이 비교적 느슨하고 분산된 특성을 가지므로 역삼투 공정과 달리 물리세정만으로도 충분한 막오염 제어가 가능하다. 하지만 기존 연구들의 경우 정삼투 물리세정에 적합한 세정 유속을 적용하지 않아 최적화 운전을 하지 못했다는 한계가 있다. 따라서 이 연구는 경제적인 에너지량으로 높은 효율의 세정을 보일 수 있는 적절한 유속의 정당성 평가를 목적으로 한다. 정삼투 공정 막오염 실험을 8.54 cm/s 순환 유속으로 유지하고 세 가지 세정유속으로 회복률과 SEC(specific energy consumption) 비교 평가하였다. 이 실험의 결과로 2배속 세정이 3배속 세정의 수투과도 회복률 만큼의 높은 효율을 보 이는 동시에, 2배속 세정이 높은 세정효율 및 경제적인 SEC를 보이는 적절한 유속이라는 것을 확인하였다.

Chlor-alkali (CA) membranes as key materials to generate chlorine gas and sodium hydroxide are composed of sulfonic acid layer (S-layer) and carboxylic acid layer (C-layer) to provide fast sodium ion transport and slow hydroxide ion diffusion, respectively. Aciplex F, a representative CA membrane is made in a double layer form via thermal adhesion of both layers after each single layer film is independently fabricated. Unfortunately, the membrane fabrication induces delamination particularly in their interface as a result of hydroxide ion diffusion occurring during CA operation, leading to rapid increase in electrochemical overpotential. In this study, selective chemical conversion technique was developed to solve the delamination issue. Their effectiveness was proved by applying the same concept to a wide range of PFSA membrane.

본 연구에서는 향후 역삼투식 해수담수화 기술의 에너지 효율을 개선하기 위한 3가지 방법을 제안한다. 그리고 제안된 방법이 적용되었을 때, 이론적인 최대 에너지 소모량 감소를 엑서지 분석을 통해 산출하고 현재 개발되고 있는 기술을 분석해서 실질적으로 각 방법에서 에너지 소모량이 얼마나 감소될 수 있는지를 비교하고 분석한다. 이러한 논의를 통해서 향후 역삼투 공정의 에너지 소모량이 얼마나 더 감소할 수 있을지에 대한 가능성을 평가할 수 있고 나아가서 역삼투 해수담수화 플랜트의 에너지 소모량을 낮추는 명확한 아이디어를 제공할 수 있다.

Saline water electrolysis (SWE) is an electrochemical technology to directly generate valued chemicals such as chlorine gas (Cl2), hydrogen (H2), and sodium hydroxide (NaOH) by applying electric energy. The key materials in SWE are cation exchange membranes with high selectivity to sodium ions under chemically harsh SWE conditions. The representative SWE membranes are perfluorinated double layered membranes composed of perfluorinated sulfonic acid layer and carboxylic acid layer to transport sodium ions rapidly and to prevent the passage of hydroxide ions, respectively. The commercially available membranes are, however, suffering from delamination issues occurring in their interface. In this presentation, delamination-free membrane fabrication processes will be addressed.

해수담수화는 지구 수자원의 97%에 해당하는 해수를 활용하기 때문에 물부족 문제를 해결할 지속가능한 대안으로 평가받고 있다. 최근에는 증발식 해수담수화 대비 에너지 소모가 낮은 분리막 방식이 널리 적용되고 있으며, 에너지 소모는 3-4 kWh/m3 정도이다. 해수담수화 플랜트 소요비용 중 운영비용이 약 35~65%를 차지하므로 해수담수화 기술의 확대 적용을 위해서는 비용 절감형 운영 기술 개발이 필수적이다. 이에 K-water에서는 ‘중동지역 맞춤형 저에너지 해수담수화플랜트 기술개발’ 과제 참여를 통해 저에너지⋅고효율 해수담수화 운영 기술을 개발하고 있으며, UAE에 구축될 1,000m3/d 규모 플랜트에 적용할 계획이다. 본 기술 적용을 통해 해수담수플랜트 연간 운영비용 증가율을 5% 이내로 유지하는 것을 목표로 한다.

일반적으로 SWRO의 경우 에너지 소비량은 3.5 kWh/m³ 이상의 에너지를 소비한다. 그중 RO트레인은 2.5～3.0 kWh/m³를 소모해 전체 에너지 소비량의 70% 이상을 소비하고 있으며, 전체 시스템 에너지 절감을 위해서는 RO트레인의 최적 설계가 중요하다. 따라서 당사는 다양한 RO트레인의 설계를 최적화 하여 소모되는 에너지의 양을 10% 절감하고자 한다. 1) ISDInternally Staged Desing)을 적용한 1st Pass의 설계최적화, 2) SPSP(Split Partial Sencond Pass) 적용을 통한 2nd 용량 최적화 설계, 3) 초고성능 막을 적용한 Single Pass 설계방법의 최적 조합을 통해 저에너지 역삼투막 시스템 설계 기술을 개발하고자 한다.

Membrane bioreactors (MBRs) have big issue on high aeration energy. In this study, reciprocation of membrane was adapted to mitigate membrane fouling. Inertial force induced by reciprocation removed foulants from membrane surface. Pilot plant with capacity of 1,100 m³/day was operated for 8 months in Singapore. The result showed stable trans membrane pressure (TMP) and low permeate turbidity below 0.1 NTU at 25 LMH. It also showed 60 times less energy consumption than conventional MBR. Low dissolved oxygen in membrane tank resulted in higher nitrogen removal. Long-term reciprocation requires very strong membrane modules. Braid reinforced membrane and its modules were optimized to reciprocation. The evaluation of them after the operation showed there was no change in all their properties.