The research led to the development of a specialized knife for cutting waste ropes and nets from marine waste. The composition of the manufactured knife was analyzed with XRF equipment, and the main components were iron and chromium, with small amounts of molybdenum, vanadium, and nickel. Vickers hardness measurements showed similar hardness values at the surface and center, and a metallographic microscope examination of the knife surface texture revealed a fine-grained martensite structure. The low heating value of the waste rope and waste net was measured, and the low heating value was higher than 3,500 kcal/kg, which is the quality certification standard for solid refuse fuel.

This study conducted a marine experiment to improve the fishing system using miniaturized nets for anchovy boat seine to reduce the fleet size. As a result, the miniaturized net for anchovy boat seine properly opened the entrance of the bag net using the buoyancy of the flotation for position indication and the setting force of the ground rope without operating a separate fish detecting boat by attaching a large flotation at the entrances of the inside wing net and the bag net. This also enabled an operation type where the entrance of the bag net is confirmed using a flotation for position indication from a netting boat. The time and the number of people used for net casting and net hauling in the marine experiment were average of five minutes and 25-30 minutes, respectively, and 23-30 people for the existent net, while for the miniaturized large-scale net were average of three minutes and 23-25 minutes, respectively, and 19-25 people. This indicates that the operation time was shortened, the number of fish detecting boats was reduced by one boat, and the number of people for fishing work was decreased by four or five people due to the improvement of fishing operation system according to the reduction of fishing net size. As a result of measuring the shaft horsepower during net towing, the maximum net towing horsepower was 250 HP in comparison to the maximum RPM of the engine (1,200 RPM), indicating that the legal horsepower of 250 HP is enough to conduct net towing and the competitiveness of fishing using the net for anchovy boat seine is ensured through operation cost reduction.

Most fishing nets used in fish cage aquaculture are made of synthetic fibers such as polyamide (PA) and polyethylene (PE). Therefore, it is challenging to maintain the internal volume of the fish cage due to biofouling, which can increase the load on the cage or reduce dissolved oxygen levels by impeding smooth current flow. To address this issue, research has been conducted to replace conventional synthetic fiber cage nets with brass nets, demonstrating certain benefits such as improved productivity and ease of fish cage management. However, given the need for a more thorough examination of brass fishing net weaving technology and performance, this study assessed the optimal weaving method for brass fishing nets to be used in fish cages. Additionally, it provided essential data for the practical application of brass fishing nets by evaluating their weight, tensile strength, elongation, fatigue resistance, and wear resistance. The study concluded that weaving brass fishing nets using the chain link method ensures durability, ease of installation, and compact storage in a scroll-like form. Moreover, due to their superior fatigue and wear resistance properties, brass nets can offer increased utility if appropriate net diameter and length are selected to compensate for their higher weight per unit area and relatively higher cost compared to existing fiber fishing nets.

At Pyropia farms, organic acid treatments have enhanced productivity and quality by removing pest algae (such as Ulva spp. and diatoms) and reducing the occurrence of diseases. Ulva spp. attaches to the Pyropia nets competing for inorganic nutrients & space and diminishing productivity. Additionally, the presence of attached contaminants (such as diatoms and middy particles) on the Pyropia nets negatively affects the quality of Pyropia. This study investigated the effects of removing Ulva linza and washing the Pyropia yezoensis nets using an activating treatment agent (organic acid and highly saline solution) with an air bubble device. The results of measuring the dead cell ratios after treatment under different conditions showed that the dead cell ratio of U. linza did not significantly increase when the air bubble device combined the activating treatment agent with the activating treatment agent alone. When washing the P. yezoensis nets, the air bubble device was about 19-37% more effective than the activating treatment agent alone. The findings of this study suggest that the air bubble device enhances the efficacy of the activating treatment agent, resulting in the effective cleaning of the Pyropia nets.

The blockage rate for three kinds of nets commonly used in agricultural facilities was assessed by using the image acquisition and its relevant processing. By using both empirical relations presented by Idel’chik and Richards and Robinson, and the blockage rate obtained from the image processing, the pressure drop through the nets was predicted and also compared with wind tunnel experiment results. The results of the study showed that the blockage rate of the net was discriminated according to such factors as the magnitude of nets, the existence of inside threads, the thickness and number of threads. In addition, the blockage rate for the incident angle of 0° when the wind blew at the front had the range of 0.22－0.29 (0.22－0.32 when considering whole incident angles from 0° to 45° by 15°). For the nets with the blockage rate of about 30% or below, the prediction by the empirical relations of by Idel’chik and Richards and Robinson showed a little higher pressure drop overall than that of the wind tunnel test, but the use of the empirical relations and the blockage rate could be thought of as providing effectively meaningful guidelines for the safe design of agricultural facilities including nets because the wind tunnel test has been tedious and expensive. Further research and potential application on the prediction technique of the pressure drop, regarding both a subtle deformation by the wind and manufacturing methods with regard to the level of knots and the existence of inside threads, needs to be done for the nets with higher blockage rate.

본 연구는 방충망 시설이 생육환경에 미치는 영향을 구명하기 위한 기초자료로 활용되도록 무봉지 재배를 위한 망 시설 테스트베드를 설치하고 온도, 습도, 풍속 및 일사량을 수집한 기상자료를 분석하여 망 시설 내·외부의 미기상 특성을 확인하고자 하였으며, 기상자료를 분석한 결과는 다음과 같다. 온도와 습도의 경우 망의 피복 여부에 따라 0.2oC, 3.5~4.7%의 차이가 발생하였으며 실험구 대비 대조구에서 수분부족분이 증가하는 경향을 보였다. 외부와 망 시설 내부에서 일사 투과율은 격자 크기에 따라 큰 차이를 나타냈다. 특히 격자 크기가 2mm인 경우 외부와의 일사 투과율이 최대 50%정도까 지 감소하는 것으로 나타났으며, 이는 과실 생육에 큰 영향을 미칠 수 있기 때문에 격자 크기 선택에 있어서 고려해야할 요소로 판단된다. 태풍 솔릭 내습시의 망 시설 내?외부의 풍속을 비교한 결과, 7 m/s이상의 고풍속 일 때 격자 크기가 4 mm 망 시설은 40% 이상, 2 mm 의 경우 50% 이상의 풍속 감소율을 보였다. 또한 풍속 저감 효과로 인한 낙과 피해도 현저하게 감소하는 것으로 나타났다. 이러한 연구결과는 망 피복에 따른 과수의 생육환경에 미치는 영향과 최근에 잦은 이상기상 발생으로 망 시설을 적용한 이상기상 피해저감 효과 등의 기초자료로 활용될 수 있을 것으로 판단된다.

The catch composition of commercially important species of the stationary lift net at Barangay Gines, Miagao, Iloilo, the Philippines was investigated from December 2013 to May 2014 during the different phases of the moon. A total of 486 kg of fish coming from 12 different genera, including mollusk and crustaceans, was caught and identified from the catch of the stationary lift net. Among the 12 genera identified from the catch of stationary lift net, anchovy (Stolephorus), sardines (Sardinella), squid (Loligo) and mysid shrimp (Acetes) were considered to be commercially important due to their value. Acetes catch was highest during the new moon in the month of January. Loligo catch was also high during the new moon except in the month of May. Stolephorus catch was also highest during the new moon except in the month of January. Sardinella catch was highest during the first quarter in the month of February. Full moon had the lowest catch all throughout the duration of the study while new moon had the highest catch during December 2013 to March 2014 and first quarter was the highest in the months of April and May.

As emphasis has increased on English as an international language and on the globalized image of universities, the number of native English speaker teachers (NETs) has also increased in Korean universities. From the poststructuralist view, teacher identity is constructed through participation in valued activities of the community of practice, and it is not fixed but constantly negotiated through the interaction of the context (Wenger, 1998). While previous studies focused on nonnative English speaker teachers’ identity construction, little attention has been paid to NETs in the EFL context. Considering the need to explore teacher identity from recent theoretical perspectives, the present study investigates how NETs negotiate conflicting identities and construct their teacher identities in the Korean university context. The findings show the NETs constructed multiple identities of an English educator, a collaborative volunteer, a non-tenured instructor, and a cultural and linguistic outsider, and they legitimize their professor identity through their participation in the present and imagined community of competent teachers. The findings support the claim that teacher identity is embedded in the sociocultural context that interacts with the individual agency in making sense of who they are. Implications and suggestions of the study are addressed based on the findings.

The project schedule risk in the engineering and facility construction industry is increasingly considered as important management factor because the risks in terms of schedule or deadline may significantly affect the project cost. Especially, the project-based operating companies attempt to find the best estimate of the project completion time for use at their proposals, and therefore, usually have much interest in accurate estimation of the duration of the projects. In general, the management of projects schedule risk is achieved by modeling project schedule with PERT/CPM techniques, and then performing risk assessment with simulation such as Monte-Carlo simulation method. However, since these approaches require the accumulated executional data, which are not usually available in project-based operating company, and, further, they cannot reflect various schedule constraints, which usually are met during the project execution, the project managers have difficulty in preparing for the project risks in advance of their occurrence in the project execution. As these constraints may affect time and cost which role as the crucial evaluation factors to the quality of the project result, they must be identified and described in advance of their occurrence in the project management. This paper proposes a Bayesian Net based methodology for estimating project schedule risk by identifying and enforcing the project risks and its response plan which may occur in storage tank engineering and construction project environment. First, we translated the schedule network with the project risks and its response plan into Bayesian Net. Second, we analyzed the integrated Bayesian Net and suggested an estimate of project schedule risk with simulation approach. Finally, we applied our approach to a storage tank construction project to validate its feasibility.

The purpose of this study is to identify the flow resistance of the bottom pair trawl nets. The bottom pair trawl nets being used in fishing vessel (100G/T, 550ps) was selected as a full-scale net, and 1/10, 1/25 and 1/50 of the model nets were made. Converted into the full-scale net by Tauti’s modeling rule and Kim’s modeling rule, when resistance coefficient k of each net was calculated by substituting into above equation for flow resistance R and wall area of nets S values of each net v. Because resistant coefficient k decreases exponentially according as flow velocity v increases to make k cv-m, c and m values of each net were compared. As a result, as the model was smaller, c and m values was smaller in the two rule into standard of 1/10 model value, decrease degree of 1/25 model was almost same in the two rule, decrease degree of 1/50 model was very big in Tauti’s modeling rule. Therefore, in the result of experiment, because average of c and m values for similarly 1/10 and 1/25 model were given c=4.9 (kgf․s2/m4) and m=0.45, R (kgf) of bottom pair trawl net could show R =4.9Sv1.55 using these values. As in the order of cod-end, wing and bag part for 1/25 and 1/50 model net were removed in turn, measured flow resistance of each, converted into the full-scale, total resistance of the net and the resistance of each part net were calculated. The resistance ratio of each part for total net was not same in 1/25 and 1/50 model each other, but average of two nets was perfectly same area ratio of each part as the wing, bag and cod-end part was 43%, 45% and 12%. However, the resistance of each part divided area of the part, calculated the resistance of per unit area, wing and bag part were not big difference each other, while the resistance of cod-end part was very large.

The heat treatment machine based on immersion was developed to reduce temperature difference during netting process and appraised it performance compared current heat treatment machine using high pressure. It was also reviewed the optimum heat treatment procedures for PBSAT monofilament net in accordance with the immersion time and temperature. The procedure was based on physical measurement such as breaking load, elongation and angle of the mesh for PBSAT monofilament. The water temperature gap of the treatment machine based on immersion was less than 1°C. and the energy consumption was also increased in high temperature condition. It was identified that the optimum temperature was 75°C and its optimum processing time was between 15 minutes and 20 minutes to get qualified physical properties.