Background: Whole-body vibration (WBV) has been used to alleviate proprioceptive damage by musculoskeletal and neurological conditions. However, no study has determined whether wearing shoes while applying WBV can affect proprioception precision of the knee joint. Objects: This study aimed to determine the differences in the proprioceptive precision of the knee joint before and after WBV and to compare the proprioceptive precision of the knee joint between barefoot and shoe-wearing conditions. Methods: This study recruited 33 healthy participants. A passive-to-active angle reproduction test was used to measure the proprioception precision of the knee joint using an electrogoniometer, and the target angle was set to a knee flexion of 30°. Proprioception precision was calculated using the error angle (angular difference from 30°). Proprioceptive precision was measured in weight-bearing and non-weight-bearing positions before and after applying WBV for 20 minutes at 12 Hz in barefoot and shoe-wearing conditions. Mixed repeated analysis of variance was used to determine the differences in changes in the proprioceptive precision of the knee joint according to foot conditions. Results: There were significant improvements in the weight-bearing (p = 0.002) and nonweight- bearing (p < 0.001) proprioceptive precision of the knee joint after applying WBV. However, there was no significant difference in the change in proprioceptive precision of the knee joint after applying WBV between the barefoot and shoe-wearing conditions. Conclusion: WBV stimulation had an immediate effect on improving the proprioceptive precision of the knee joint. However, foot conditions (barefoot or shoe-wearing) during WBV application did not influence the proprioceptive precision of the knee joint.

제주도 북서부인 애월 해안에는 평탄하게 흐른(판상) 용암류와 둥근 모양(원통)의 용암류가 관찰된다. 원통형 용암류의 치밀한 내부에는 동심원 구조와 방사상 절리가 발달한다. 구엄리 돌염전 주변의 판상 용암류 내부에는 상하부의 굵기가 다른 주상절리가 발달한다. 주상절리 상부는 다각형의 형태가 고르지 않으며 직경은 120-150 cm이다. 주상절리 하부는 육각형과 오각형으로 형태가 일정하고, 크기도 60 cm 내외이다. 원통형 로브는 크기와 형태에 따라 두 그룹으로 나눌 수 있다. 하나는 메가로브인데, 최대 직경이 30 m인 반원형이다. 또 하나는 원형의 로브로 직경이 10 m 이하이다. 원통형 용암류의 방사상 절리의 기둥 단면은 육각형과 오각형이며, 기둥의 직경은 중심에서 바깥쪽으로 증가하는데 바깥쪽 경계부에서는 80-120 cm 정도이다. 원통형 용암에서 관찰되는 동심원 구조는 4가지 요인이 복합된 것이다. 첫째는 원형의 균열로, 원통형 용암류 내에서 안쪽과 바깥쪽 사이의 온도차와 밀도차로 발생한 수축으로 생긴 틈새이다. 둘째는 방사상 절리의 마디층이 동심원을 이룬 것으로, 이 마디층은 방사상 절리와 동시에 만들어진 것이다. 셋째는 유동 띠로서, 용암이 흐를 때 둥근 통로에 남긴 흔적이다. 네 번째는 용암에서 빠져나온 가스가 동굴에 형성된 기공 띠이다.

목조건축물에 주로 적용되고 있는 철물 접합 시스템은 모재인 나무와 접합부재인 철재 간의 강도 차이 및 재질의 이질성으로 인한 외관상의 위화감 등이 문제점으로 대두되고 있다. 재료 가공의 편의성으로 프리컷 시스템이 도입되었고, 시공성 을 해결하기 위한 새로운 재료 및 시스템의 개발이 요구된다. 본 연구에서는 자연재료를 그 원료로 하여 미관상 목조건축물에 위화감이 없는 황토 압밀 플레이트를 개발하였다. 황토 및 소석회를 원료로 하여 제작한 시험체의 양생방법(기건 양생, CO2 양 생)에 따른 성능을 평가하기 위해 질량 변화, 지압 강도, 흡수율, 표면상태, 열중량변화 측정 및 SEM을 통한 생성광물의 미시적인 부분을 관찰하였다. 또한 제조과정에서의 온실가스 배출 및 흡수에 따른 환경성능평가를 수행하였다. 기건 양생한 시험체에 비해 CO2 챔버에 양생한 시험체는 원료인 소석회의 탄산화 반응으로 인한 탄산칼슘의 생성으로 역학적 성능이 향상되었다는 것을 알 수 있었으며, 원료인 소석회의 탄산화반응으로 인해 생석회 제조시 발생하는 CO2량의 70% 이상을 재흡수 한다는 것을 알 수 있었다.

PURPOSES : This study was conducted to evaluate the performance of pressure relief joints (PRJs) installed on highways for preventing blow-ups. METHODS : To evaluate the performance of a PRJ, pavement surface images were acquired by conducting a follow-up survey through on-site visual inspection and an automated pavement condition survey. The PRJ widths in the acquired pavement images were measured using image analysis software, and major distress in the PRJ was identified. The relationship between the performance period and the joint width was bi-linearized, and the causes of distress and repair methods for PRJ were suggested. RESULTS : As a result of the first survey, it became known that the width of a PRJ rapidly decreases after installation owing to an expansion of the concrete slab. The width of a PRJ continued to decrease, with 94% of the joint below 30 mm and 64% of the joint being below 10 mm, based on the fourth survey. The PRJ width of an Alkali-Aggregate Reaction (AAR) section decreased more than that of a normal section, but the difference in the average width between both sections decreased from 9.7 mm to 2.7 mm over the measured period. A bilinear estimation equation was developed based on the survey data. Through the estimation equation, it could be confirmed that joint contraction accelerated after installation owing to the effects of AAR, and that the joint widths of both sections converged to a similar level over the measurement period. As the result of the major distress analysis indicates, joint seal failure occurred in 70% of the joints, and the distress rates in terms of cracks, edge breakouts and spalling, and patching were 73%, 57%, and 28%, respectively. CONCLUSIONS : With the follow-up survey it could be confirmed that the concrete slab continued to expand despite seasonal changes, maintenance of the PRJ, and additional installation of new PRJs. The expansion of the concrete slab due to AAR is considered to be closely related to PRJ behavior. In addition, it is judged that major distress of the PRJ occurs at an early age owing to the instantaneous release of excessive compressive stress inherent in the slab during joint cutting.

Leiomyoma is a Benign tumor that develops in smooth muscles and is known to occur more in women in age between 40s and 50s. The most common site of leiomyoma is uterine (95 %). It occurred in oral region is very rare about 0.065 % and usually developed in upper and lower lips, palatal site, buccal site and tongues. The prognosis of leiomyoma is very positive. The recurrence rate is extremely low to 2 % below. In present study, we report a 78 year old female with a lesion located in temporomandibular joint cavity which was suspected as a malignant tumor. Additionally, this paper reports contains a literature review of oral leiomyoma. Rare location with painless leiomyoma of present case will be considered to be caution.

In this study, experiments and simulations were performed for fillet joint friction stir welding according to tool shape and welding conditions. Conventional butt friction stir welding has good weldability because heat is generated by friction with the bottom of the tool shoulder. However, in the case of fillet friction stir welding, the frictional heat is not sufficiently generated at the bottom of the tool shoulder due to the shape of the tool and the shape of the joint. Therefore, it is important to sufficiently generate frictional heat by slowing the welding speed as compared to butt welding. In this study, experiments and simulations were carried out on an aluminum battery housing made by friction stir welding an extruded material with a fillet joint. The temperature of the structure was measured using a thermocouple during welding, and the heat source was calculated through correlation analysis. Thermal elasto-plastic analysis of the structure was carried out using the calculated heat source and geometric boundary conditions. It is confirmed that the experimental results and the simulation results are well matched. Based on the results of the study, the deformation of the structure can be calculated through simulation even if the tool shape and welding process conditions change.

The bead geometry according to the welding conditions was analyzed through the laser fillet welding experiment of 9% Ni steel, and the relationship between the shear strength and the five bead geometry measured by selecting the main bead geometry of the fillet weld was analyzed. Among the welding conditions, the welding conditions that directly affect the penetration depth are welding speed and laser power, and the working angle and beam position have a great influence on the formation of leg of vertical and horizontal members. The bead shape, which greatly affects the shear strength, is the horizontal member length, neck thickness, and weld length, and has a proportional relationship with the shear strength. As a result of confirming the relationship between shear strength and bead shape through the derivation of the trend line, it was confirmed that the length of the vertical member, whose R2 value was 0.92, was most closely related to the shear strength.

The premature failure of the universal joint connecting the drive gear box and the cooling fan caused a deterioration in serviceability and operability. Universal joint is a device that transmits engine power to a cooling fan. Internal pin breakage and shaft separation can cause secondary damage such as cooling fan malfunction and radiator damage caused by component failure. The purpose of this paper is to analyze the damage phenomenon of universal joints caused by bundles in SPVs and to improve them. In order to verify the improvement, a single part test and a system conformance test were conducted, and durability test was conducted to confirm the improvement effect on the improved prototype. Through these, the effects of increasing the durability of the improved product were estimated.

Background: Patients with stroke have core muscle weakness and limited rib cage movement, resulting in restrictive lung disease. Objectives: To examine the comparison of effects of rib cage joint mobilization combined with diaphragmatic breathing exercise and diaphragmatic breathing exercise on the pulmonary function and chest circumference in patients with stroke. Design: A cluster randomized controlled trial. Methods: Twenty-four patients were randomly assigned to an experimental group (rib cage joint mobilization combined with diaphragmatic breathing exercise group) and control group (diaphragmatic breathing exercise group). Patients in the experimental group underwent rib cage joint mobilization for 15 min and diaphragmatic breathing exercise for 15 min. The control group underwent diaphragmatic breathing exercise for 30 min. Both groups underwent exercise thrice a week for 4 weeks. The pulmonary function and chest circumference were measured using the MicroLab spirometer and a tape measure, respectively. Results: After the intervention, the pulmonary function and chest circumference significantly improved in both groups. These improvements were significantly higher in the experimental group than those in the control group. Conclusion: Rib cage joint mobilization combined with diaphragmatic breathing exercise improves pulmonary function and chest circumference in patients with stroke.

Background: With the increasing elderly population, the need for gait analysis of these elderly individuals is also increasing. Most devices are costly and not portable; however, smartphones using built-in sensors capable of measuring motion and are easily available. Objectives: To examine the reliability and validity of knee joint angles of the elderly using smartphone measurements during walking. Design: Quasi-experimental research. Methods: Sixteen elderly people, aged 65+ and living in Daejeon and Chungbuk, South Korea, participated in the study. Electrogoniometers and smartphones were attached to the thigh and the side and front of the shank of each subject, respectively, using double-sided tape, an arm band, and an elastic band. Each subject completed two sets of at least seven gait cycles (14 steps). Results: Both the smartphones and electrogoniometers exhibited high agreement in terms of their primary and secondary measurements (ICC>.75). The agreement between the smartphones and electrogoniometers was also high in terms of both the primary and secondary measurements (ICC<.60). Conclusion: These results indicate that smartphones can be costly equipment cannot, even though they cannot completely replace existing clinical-grade devices. Their utility is emphasized herein for measuring knee joint angles of the elderly during walking.

본 연구는 외발 착지 시 신체적 특성 요인들인 발목 유연성, 성별, Q-angle이 발목 관절 상해 요인들에 미치는 영향을 분석하는데 목적이 있었다. 이를 위해 오른발을 주발로 사용하고 체육을 전공하는 20대 남성 16명(나이: 20.19±1.78 years, 체중: 69.54±10.12 kg, 신장: 173.22±4.43 cm), 여성 16명(나이: 21.05±1.53 years, 체중: 61.75±6.97 kg, 신장: 159.34±4.56 cm)을 연구대상자로 선정하였다. 외발 착지 시 신체적 특성 요인들이 발목 관절 상해에 미치는 영향을 확인하기 위하여 첫째, 발목 상해 경험에 따른 하지 관절 움직임과 관절 모멘트의 독립 t-test를 실시하였다(α = .05). 둘째, t-test를 통하여 유의한 차이를 나타낸 변인을 종속변인으로 설정하고 발목 유연성, 성별의 차이, Q-angle을 독립변인으로 지정하여 선형다중회귀분석(Multiple Linear Regression)을 사용하였다(α = .05). 본 연구결과 발목 관절 상해를 경험한 그룹은 상해를 경험하지 않은 그룹과는 다르게 발목 관절의 내전, 무릎 관절의 내측 회전을 통한 착지 전략과 기술을 사용하는 것으로 나타났다. 또한 이러한 움직임은 발목 관절의 신전 모멘트를 증가시키고, 엉덩 관절의 신전 모멘트는 감소시키는 것으로 확인되었다. 특히 발목의 배측굴곡 유연성은 발목과 무릎의 착지전략에 영향을 미치며, 성별의 차이는 발목의 신전 모멘트에 영향을 미치는 것을 알 수 있었다. 따라서 외발 착지 시 신체적 특성 요인들이 발목 관절 상해에 영향을 미치는 요인들임을 확인 할 수 있었다.

2017년 미국 DOE 주도하에 수행된 국제공동 복합모드운반시험 중 도로트럭운반시험, 연안항해시험, 대서양항해시험에서 측정된 가속도 및 변형률 데이터를 분석하였다. 먼저 각 운반모드 별로 발생한 하중이 전달경로에 따라 하중이 증폭되는지 감쇄되는지가 조사되었다. 그 결과 운반모드 및 하중경로 내 어떤 부분이냐에 따라 발생한 하중이 모의핵연료집합체에 전달되는 특성이 다름을 확인하였다. 그리고 변형률 데이터를 분석하여 육상 및 해상운반동안 발생한 변형률이 사용후핵연료에 건전성에 미치는 영향을 파악하였다. 그 결과 측정된 변형률은 사용후핵연료의 건전성에는 영향을 미치지 못하는 정도로 작은 크기임을 확인하였다. 본 연구에서 분석된 가속도와 피로평가 결과는 예정된 국내 정상운반시험조건에서의 운반시험에 유용한 기초자료로 활용될 것이다.

Background: Based on the understanding of the muscle activation relationship between the infraspinatus and posterior deltoid muscles to according to the angle of motion during external rotation on glenohumeral joint, effective shoulder joint strengthening exercise for the prevention and rehabilitation of shoulder injury due to muscle strength imbalance can be performed by achieving the ideal muscle activity ratio during exercise. Objectives: To compare and analyze the muscle activation changes and activity ratio of the infraspinatus and posterior deltoid muscles according to the glenohumeral external rotation angle. Design: Quasi-randomized trial. Methods: The study included 48 healthy male and female adults who provided informed consent for participation in the study. All the subjects performed isometric glenohumeral external rotation by setting the angle of motion to 30°, 45°, and 60° using a 5 kg resistance weight pulley. On surface electromyography, the differences in muscle activation and activity ratio between the infraspinatus and posterior deltoid muscles were investigated. Results: A significant difference in muscle activation was found in the comparison between the infraspinatus and posterior deltoid muscles according to the glenohumeral external rotation angle (P<.05). The muscle activation levels of the infraspinatus and posterior deltoid muscles were highest at the external rotation angles of 30° and 60°, respectively. The muscle activity ratio between the infraspinatus and posterior deltoid muscles also showed a significant difference (P<.05) and was highest at the shoulder external rotation angle of 30°. Conclusion: The findings of this study suggest that muscle activity is the highest at the shoulder external rotation angle of 30° in healthy individuals.

본 연구의 목적은 딥 스쿼트 동작 시 발목 관절 유연성이 무릎 관절의 운동역학적 요인들간의 관련성을 분석하는데 있었다. 본 연구는 최근 1년간 하지 근골격계 병력이 없는 성인 남성 19명과 여성 8명이 연구대상자로 참여하였다. 딥 스쿼드 시 발목 관절 유연성과 하지 관절의 운동역학적 요인들과 상관관계를 검증하기 위해 pearson의 적률상관계수(pearson’s correlation coefficient)를 이용하였고(SPSS 24.0, Armonk, NY, USA), 통계적으로 유의미한 상관성을 나타낸 변인들은 단순회기분석(simple regression analysis)을 실시하였으며, 유의 수준은 .05로 설정하였다. 본 연구를 통해 발목 관절 유연성과 무릎 관절의 압력을 결정하는 최대 관절모멘트와 관절반발력 요인들 간의 관련성을 확인할 수 있었다. 그러므로 근력 트레이닝 시 딥 스쿼트와 같은 무릎 관절에 많은 부하를 발생시킬 수 있는 운동을 적용할 때 개인에 신체적 특성 중 발목 관절의 유연성의 정도를 확인하는 것은 신체의 안정성과 무릎 관절의 상해 위험성을 감소시킬 수 있는 운동 강도를 설정하는데 도움이 될 수 있을 것으로 기대한다.

PURPOSES : This study deals with a pressure relief joint, which is one of primary preventive methods of blow-up in concrete pavement. The purpose of the study is to estimate the joint sealant protrusion of pressure relief joint filler types according to horizontal displacement of concrete pavement by applying a variety of joint sealants and joint fillers. And test method for resistance of concrete to chloride ion penetration and test method for resistance of concrete to rapid freezing and thawing were conducted to analyze the improvement of concrete durability according to the primer types on concrete surface of stress relief joint. METHODS : Joint fillers of pressure relief joint were categorized into four different types, which are was styrofoam+backer+sealant(type 1), styrofoam+sealant(type 2), foaming styrofoam+sealant(type 3), and preformed joint+sealant(type 4). By varying the depth (10, 20, 30, 50 mm) from the top of the test specimens to the sealant’s surface, the test factors were evaluated for a total of 16 variables. When the specimen’s joint spacing decreased from 70mm to 10mm, the load was stopped. And the displacement of the center of the joint protrusion was measured. The test was terminated when the specimen joint spacing was reduced to 60 mm. The horizontal displacement at the time when the joint protrudes over the specimen surface is recorded and analyzed as the critical threshold displacement. RESULTS : According to the test results according to the type of joint filling material, it was found that there was a difference in the protrusion of the horizontal compression displacement according to the joint filling type. Under the current installation standard of 20mm, the preformed seal joint member showed the best crimping characteristics by securing the safety against protrusion until the horizontal displacement of 50mm occurred. CONCLUSIONS : The most common failures in pressure relief joints are those related to joint sealants, which can be minimized by changing the current joint type, installation depth, etc. to suppress them.

Background: Lateral epicondylitis (LE) is the most common chronic musculoskeletal pain condition of the upper extremities. LE is often related to forceful grip activities that require isometric contraction of the wrist extensors. A previous study evaluated the effect of the diamond taping technique on grip strength and pain; however, there has been no report on the change in the electromyography (EMG) findings of wrist extensors. Objects: The aim of this study was to investigate the effect of diamond taping technique, using a rigid tape, on the EMG activities of the extensor carpi radialis (ECR) during grip activities. Methods: Twenty-four healthy subjects (mean age = 21.50 ± 2.76 years) volunteered to participate in this study. The subjects were instructed to perform forceful grip activities with and without diamond-type taping on the origin area of the ECR. Grip strength tests were performed at 100%, 75%, 50%, and 25% for maximal isometric contraction force. EMG data were collected from the ECR. Repeated measure analysis of variance was used to analyze the effect of grip force and taping (with and without). Statistical significance levels were set at α = 0.05. Comparison of the results with and without taping at different grip force were analyzed using independent t-test. Statistical significance levels were set at α = 0.01. Results: Statistically significant association was observed between the taping application and forceful grip activity as revealed by the EMG data of the ECR (p < 0.05). EMG of the ECR significantly reduced for all muscle strength levels (p < 0.01) after taping. Conclusion: This study shows an impressive effect of the diamond taping technique, using rigid tape, on wrist extensors during grip activities. Decreasing muscle activity via this taping approach could be utilized to enhance pain-free grip force and reduce pain in patients with LE. Our study suggested that this taping technique could be considered as an effective management strategy of LE.

The purpose of this study was to assess knee joint loading in the target knee during a golf swing compared to loading rates of high impact activities such as cutting and drop landings. Nine healthy competitive golfers completed golf swings with the target foot both straight and externally rotated 30 degrees, as well as drop landings and cutting maneuvers. Motion capture data was collected at 240 Hz and ground reaction force data was collected at 2400 Hz. The frontal and transverse knee moments were examined using repeated measures ANOVA through SPSS. The abduction moments were higher in golf swings as compared to the other high impact activities (p=.010), while the external rotation moments were lower (p=.003). There were no significant differences between externally rotated and neutral golf swings. These results suggest moments applied to the knee during a golf swing are similar to those applied during a high impact activity.

본 연구의 목적은 유도 허벅다리걸기 기술 발휘 시 발목 관절의 테이핑 처치가 하지 관절과 압 력중심(COP, center of pressure)에 미치는 영향을 분석하는데 있었다. 대학 유도 선수 20명(연령, 20.9±0.8세; 신장, 168.6±7.4cm; 체중, 73.5±11.6kg; 신체질량지수, 25.7±2.6kg/m2)이 참여하였으며, 발목 관절 테이핑 처치 전과 후의 2가지 조건에서 허벅다리걸기 기술 발휘 시 지지다리 관절의 각도와 압 력중심 요인을 분석하여 다음의 결과를 도출하였다. E2(t=2.411, p=.027) E4(t=2.388, p=.029)시점에서 발목 관절의 각도는 테이핑 처지 전에 비해 처치 후 발목의 각도가 통계적으로 적은 수치를 나타내었고, E2(t=-2.343, p=.032) E3(t=-4.531, p=.000)시점에서 힙 관절의 각도는 통계적으로 크게 나타났다. 그리 고 발목 관절 테이핑 처치 후 좌·우의 COP 이동은 상대를 메치는 P3 국면에서 통계적으로 크게 나타났으 며(t=2.670, p=.016), 전·후의 COP 이동은 상대의 무게 중심을 기울이는 P1 국면에서 통계적으로 적은 수 치를 나타내었다(t=2.846, p=.011). 그러므로 허벅다리걸기를 특기로 사용하는 유도 선수들은 발목 관절 테이핑으로 인해 발생하는 지지관절의 운동 기능과 COP의 이동범위를 고려하여 사용하는 것에 대하여 제 안하고자 한다.

경주지진과 포항지진으로 수도관 파열과 상수도관 누수가 보고되었다. 따라서 상수도 시설의 지진안전성 확보는 지속적이고 안정적인 물공급을 위하여 중요한 이슈이다. 상수도관은 주로 도로 하부나 일반 성토지반에 매설되어있기 때문에 지진파에 의한 변형뿐만 아니라, 지반의 영구변형, 사면의 불안정성 및 지반 액상화 등에 의한 배관의 굽힘 변형이 발생하게 된다. 이러한 배관의 굽힘 변형이 과도하게 발생 되면 배관 이음부 변위허용량을 초과하여 손상 및 누수로 이어지게 된다. 따라 서, 상수도관 이음부의 허용 변형각이 산출되어야 지진으로 인한 지반의 변형에 대하여 상수도관의 지진안전성을 정확하게 평가할 수 있다. 상수도 시스템은 현장 상황과 설치 여건에 따라 다양한 종류의 상수도관을 이용하고 있다. 그중 주철 상수도관은 오랜 기간 사용되고 개선되어 일반적으로 널리 사용되고 있다. 본 연구에서는 한국주철관공업(주)에서 제작한 EZ-LOK 조인트가 적용된 주철 상수도관에 대하여 4점 굽힘시험을 수행하였으며, 매설된 주철 상수도관의 내진 및 내침하 설계기준인을 참조하여 지진안전성을 평가하였다.