PURPOSES : The purpose of this study was to improve the performance of concrete pavements by decreasing measurement deviations using an Internet of Things (IoT)-based air content measurement device. METHODS : We calculated the properties of concrete which varied according to the air content. For a low measurement deviation, the concrete pavement performed according to the design standard. To confirm the difference in the performance of the concrete pavement for various air contents, we verified the change in the relative dynamic modulus according to the number of freeze–thaw cycles for each value of the air content. In addition, we analyzed the number of durability cracks according to the freeze–thaw cycles in the field. RESULTS : We confirmed that IoT-based measurement equipment improved the performance of pavements without changing their mixing designs or specifications. We confirmed that the performance of concrete pavements changed even with variations in air content within the range of quality standards. Using IoT-based air content management, we confirmed the reduction in concrete pavement durability cracks without changing the mixing design. CONCLUSIONS : We confirmed that IoT-based air-content management improved pavement performance. The feasibility of extending this concept to manage other concrete properties such as the chloride content should be acknowledged. Future research will require laboratory tests to understand the variation in concrete properties with varying air contents and to consider diverse load conditions.

PURPOSES : This study aims to analyze and summarize test results related to permeable blocks used for sidewalks and roadways as an alternative to conventional urban road pavement technology, specifically focusing on low-impact development (LID) techniques. Furthermore, it aims to provide reference data on the feasibility of current policy implementation and future policy directions through a longterm analysis of the performance and durability of permeable blocks in sidewalk and roadway construction. METHODS : The research methodology involves (1) conducting a survey on the status and actual conditions of permeability sustainability tests based on the results of permeability persistence tests conducted in Seoul over nine years, from 2013 to 2021; (2) analyzing the differences between the permeability block rating system of Seoul City and that employed by the Ministry of Environment; (3) analyzing the permeability of graded pavement sections in permeable blocks for sidewalks after three years of public use and deriving a regression analysis formula to estimate the maintenance period; (4) analyzing the permeability of pavement sections in permeable blocks for roadways after five years of public use and deriving a regression analysis formula to estimate the maintenance period. RESULTS : This study revealed significant improvements in the performance and quality control of permeable blocks since the implementation of the permeability sustainability test in Seoul in 2013. An analysis of the differences in the permeability coefficient and distribution based on the rating systems of Seoul City and the Ministry of Environment showed that rating system of Seoul City has approximately twice the permeability coefficient quality standard compared to that of the Ministry of Environment. Regression analysis indicated that the firstgrade permeable block was predicted to maintain its permeability for approximately 5.1 years, whereas the third-grade permeable block was predicted to maintain its permeability for approximately 3.1 years. In roadway-permeable block pavements, the first-grade sections maintained excellent quality conditions even after five years, and regression analysis predicted a permeability maintenance period ranging from eight to 17 years. CONCLUSIONS : The correlation analysis of the permeability coefficients based on the common usage period of permeable blocks for sidewalks and roadways presented in this study can provide more accurate estimations of commonality. However, further research under various environmental conditions is required to supplement these findings. Considering the lack of studies on permeable block commonality analysis in Korea, this study highlights the significance of conducting long-term experimental follow-up research to establish commonality prediction formulas for different usage scenarios.

PURPOSES : The purpose of this study was to improve the performance of concrete pavements by measuring the unit-water content with an Internet-of-Things (IoT)-based unit-water content measurement device at an increased precision compared with that of existing measuring equipment. METHODS : We calculated the properties of concrete that varied according to variations in the unit-water content. To confirm the change in the performance of concrete pavements, we compared and analyzed the fatigue cracking rate and international roughness index of concrete pavements at the 20-year point of public use according to the changes in properties using the Korea Pavement Research Program(KPRP). RESULTS : We confirmed that IoT-based measurement equipment can improve the performance of pavements without changing their mixing designs or specifications. We confirmed that the performance of the concrete pavements changed significantly, even with unit-water content variations within the range of quality standards. According to IoT-based unit-water content management, we confirmed that the performance of the concrete pavement (fatigue cracking rate and international roughness index) improved without changing the mixing design. CONCLUSIONS : We confirmed that by using IoT-based unit-water content management, pavement performance can be improved. It is necessary to consider whether the application of this concept to other concrete property management items, such as the chloride content, is possible. Considering the changes in concrete properties according to the unit-water content based on laboratory tests and considerations of various load conditions will be necessary for future research.

PURPOSES : Currently, the domestic construction industry is dominated by large-scale projects such as roads, ports, airports, and buildings. Construction on such projects is generally conducted simultaneously, but the process and quality management are led by a small number of responsible managers. In the case of road pavements, owing to rapid industrial development, economic growth, and the expansion of social overhead capital investment in the road construction industry, highways and general national roads have been constructed on a large scale. Therefore, this study aimed to improve and develop domestic concrete production and construction quality management by improving the reliability and transparency of production quality management and simplifying business processes. This was accomplished through the development of an Internet of Things (IoT)-based cement quality management system capable of automated design and build (D/B) construction and real-time monitoring. METHODS : The "IQ" system is a quality management system for enabling real-time monitoring of D/B quality at the time of concrete production and according to the designated age by utilizing quality test equipment developed with an LTE-Bluetooth function. It is possible to immediately identify and respond to quality problems through real-time monitoring, secure a reliable quality D/B because the quality test results cannot be arbitrarily manipulated, and to simplify the work process through the automatic D/B construction. In addition, improved quality control can be achieved through real-time information sharing and feedback system operations between contractors, managers, and personnel involved in construction. The quality control test items for developing the IQ system are the compression and flexural strengths, as these can be used to determine the design standard strength of pre-curing concretes (such as their slump and unit quantity) and the adequacy of the workability and durability, as well as the air volume to predict the durability, and the chloride content in the sections where reinforcement is used. CONCLUSIONS : This study identified difficulties and limitations in quality management according to the operation method in the domestic quality management systems, and in the real-time monitoring between managers and contractors. Thus, it was necessary to establish an improved systematic and reliable quality management system. The IQ system was developed to solve this problem.

PURPOSES : The increasing heat wave warnings during the summer season in Korea have significant impacts on daily life and industry as a whole, especially in urban areas (such as areas with asphalt and sidewalk pavements). Heat waves directly affect urban heat island and heat dome phenomena. Various urban temperature reduction measures are being discussed to reduce urban heat islands and heat dome phenomena and to improve citizen safety against summer heat waves; suggestions include thermal packaging, rooftop greening, and expansion of vegetation areas. There is a lack of analysis on the methodology for increasing the road spraying effect during summer heat waves (e.g., there is no systematic engineering study on the effect from reducing the temperature of the road spraying during a heat wave in the city) and on the types of road pavements in the city. In addition, as the asphalt pavements of roadways and block pavements installed in sidewalks account for a considerable portion of all pavements, this study provides a more systematic and scientific approach and procedures for reducing temperatures through road spraying in the city by tracking the effects of heat waves. METHODS : In this preliminary experiment, four types of road pavement materials were selected as test specimens: asphalt test specimens (AP- 300 mm × 300 mm × 50 mm), concrete test specimens (CP-300 mm × 300 mm × 50 mm), impermeable blocks (IB-200 mm × 200 mm × 60 mm), and self-permeable blocks (PB-200 mm × 200 mm × 60 mm). As a test method to evaluate the size and duration of each spray effect package type, the surface temperature of each specimen was measured using thermal imaging cameras every 20 min after spraying at the maximum temperature point of each specimen, and the average surface temperature was analyzed based on the collected temperature data. In addition, to conduct a quantitative analysis of the effect of reducing the surface temperature of road pavements by road spraying in summer, field tests were conducted on asphalt roads and watertight blocks for sidewalks. RESULTS : As a result of the comparative analysis of the spray effect under a 36 ℃ air temperature based on a heat wave warning, the surface temperatures were, from high to low, the asphalt (68.8 ℃), concrete (59.1 ℃), impermeable block (57.3 ℃), and permeable block (58.7 ℃). The asphalt pavement had the greatest effect on the heat island and heat dome phenomena. From measuring the temperature reduction effect and sustainability of each type of road pavement, the surface temperature reduction effects were ranked in the following order: water-permeable block (Δ18.0 ℃), asphalt test piece (Δ17.5 ℃), concrete test piece (Δ12.2 ℃), and water-permeable block (over 240 min). In the report pitching block, the average road surface temperature reduction between the pore recovery and treatment was expected to continue to decrease by approximately -4.3 ℃ on the day of work and approximately -2.4 ℃ on the next day. The expected effect of the temperature reduction owing to simple spraying on the surface of the pore block was evaluated to be limited to the day. CONCLUSIONS : In the road spray effect analysis conducted on the common asphalt road, there was a slight difference in the initial temperature reduction size as the test specimen was measured, but the surface temperature difference between the non-spray section and spray section tended to be approximately Δ3°C after 140 minutes of spraying. Therefore, it was determined that the asphalt pavement temperature reduction plan through road spraying in urban areas in summer would be the most effective if it was repeated twice or more in an hour (between 13:00 and 14:00) on the day of the heat wave.

PURPOSES : In this study, the results of an intensive field survey of a composite pavement applied to an expressway in Korea are analyzed. The results are intended to be used as basic data for evaluating the composite pavement and for preparing quality control measures through a review and analysis of the change in the state of the tensile bonding strength of the composite pavement. METHODS : To evaluate, repeated field coring and indoor tensile bonding strength evaluations are conducted for five years, and the commonality evaluation of pavement using pavement condition investigation equipment is conducted annually. RESULTS : The results of this study show that the degree of reflective crack generation varies depending on the type of concrete pavement and type of asphalt mixture applied to the intermediate layer, and that the CRCP composite pavement exhibits better initial commonality than the JCP composite pavement. In addition, it is confirmed that the composite cross-section pavement section with MASTIC applied as an intermediate layer shows excellent adhesion performance between the lower concrete layers from the beginning of construction in all sections, as well as satisfied the quality control standards for good pavement and tensile adhesion even after approximately five years of public use. CONCLUSIONS : Based on a follow-up survey of the composite pavement testing sections, it is confirmed that the section constructed with the MASTIC intermediate layer and CRCP satisfies the quality control standards for good pavement conditions and tensile adhesion even after approximately five years of public use.

PURPOSES : Korea Expressway Corporation has been working on an early remodeling project for the Jungbu Expressway to prepare methods for the rehabilitation of the old CRCP(Continuous Reinforced Concrete Pavement). In this study, the distress of the old CRCP was classified, and the engineering properties of the core specimens for each failure type were evaluated. Based on the test results, the concrete conditions of the existing CRCP were evaluated. This provides a basis for the pre-treatment or repair of the existing CRCP in the JungBu Expressway. METHODS : To evaluate the pavement condition of the Jungbu Expressway, existing PMS(Pavement Management System) data were analyzed, and field surveys were conducted for each pavement condition. The longitudinal rebar depth, rebar spacing, horizontal crack, and pavement thickness were examined through core sampling and non-destructive testing. In addition, the core specimens were used to evaluate the compressive strength, chloride penetration test, chloride ion penetration resistance, and freeze-thaw resistance. RESULTS : From the analysis of existing PMS data, field surveys, and laboratory tests, it was found that the old CRCP condition of the Jungbu Expressway was not good. Various types of failures occurred, and horizontal cracks at the rebar location, upward rebar locations, and rebar corrosion were confirmed. In addition, the compressive strength was considerably high, but the durability-related index was judged to be poor. CONCLUSIONS : For the remodeling project of the Jungbu Expressway, appropriate repairs should be carried out for each type of distress in the old CRCP.

PURPOSES : This study deals with a pressure relief joint, which is one of primary preventive methods of blow-up in concrete pavement. The purpose of the study is to estimate the joint sealant protrusion of pressure relief joint filler types according to horizontal displacement of concrete pavement by applying a variety of joint sealants and joint fillers. And test method for resistance of concrete to chloride ion penetration and test method for resistance of concrete to rapid freezing and thawing were conducted to analyze the improvement of concrete durability according to the primer types on concrete surface of stress relief joint. METHODS : Joint fillers of pressure relief joint were categorized into four different types, which are was styrofoam+backer+sealant(type 1), styrofoam+sealant(type 2), foaming styrofoam+sealant(type 3), and preformed joint+sealant(type 4). By varying the depth (10, 20, 30, 50 mm) from the top of the test specimens to the sealant’s surface, the test factors were evaluated for a total of 16 variables. When the specimen’s joint spacing decreased from 70mm to 10mm, the load was stopped. And the displacement of the center of the joint protrusion was measured. The test was terminated when the specimen joint spacing was reduced to 60 mm. The horizontal displacement at the time when the joint protrudes over the specimen surface is recorded and analyzed as the critical threshold displacement. RESULTS : According to the test results according to the type of joint filling material, it was found that there was a difference in the protrusion of the horizontal compression displacement according to the joint filling type. Under the current installation standard of 20mm, the preformed seal joint member showed the best crimping characteristics by securing the safety against protrusion until the horizontal displacement of 50mm occurred. CONCLUSIONS : The most common failures in pressure relief joints are those related to joint sealants, which can be minimized by changing the current joint type, installation depth, etc. to suppress them.

PURPOSES: Spalling is one of the primary problems that lead to the damage of concrete pavements. The purpose of the study is to analyze the impact range of spalling that occurred in an area of concrete pavement by applying a variety of nondestructive and destructive testing methods. METHODS: Spalling of the concrete pavement was categorized into four different sizes, 0 cm, 7.5 cm, 15 cm, and 30 cm. Nondestructive and destructive tests were performed at the point of spalling and 1 m away, respectively, and the obtained results were compared. The nondestructive tests included the electrical resistance test and the ultrasonic velocity test as well as strength tests by Schmidt hammer and concrete tester. The destructive tests included the direct compressive strength test and the chloride content test using field cored specimens. The test results helped in the analysis of the correlation between the current spalling damage condition and the expected damage acceleration. RESULTS: Based on the present study, the repair area and depth of spalling for a partial depth repair was suggested. It was also shown that the size of the spalling is highly correlated with the chloride content and the electrical resistance of the concrete pavement. CONCLUSIONS: The degree of spalling deterioration was found to be highly correlated with the chloride content and electrical resistance of the concrete pavement and based on the results, the extent of repair could be determined more quantitatively.

PURPOSES : In this study, we evaluated the quality levels of abrasion resistance and freeze-thaw resistance to the surface layer (colored layer) by using an overseas abrasion resistance test method to confirm the quality suitability of the concrete block surface for a domestic production permeable block. METHODS : In this study, a new evaluation item for increased durability apart from the quality standard of the permeable block was considered, namely, evaluation of the durability of the surface layer and the freeze-thaw resistance of the permeable block itself by EN 1338, ASTM C 779, 994, and GR 4009 (KS F 4419). RESULTS : The abrasion resistance test for the permeable block revealed that there were relative differences according to the different test methods. However, it was observed that if the ASTM C 779 test results did not meet the wear resistance quality standards, it did not satisfy ASTM C 944 and EN 1338. The ASTM C 779 test result was analyzed to have the highest objectivity and discernment, and this test method was proposed as a permeable block wear test method. In addition, the freeze-thaw resistance test method by the GR 4007 standard can be measured by strength, so it is possible to evaluate the resistance of the permeable block through this test method. CONCLUSIONS : The abrasion resistance test and freeze-thaw resistance test can contribute to the improvement of the permeable block when added to the current quality evaluation tests.

PURPOSES : This study was conducted to analyze the problems of the permeable block by objectively evaluating the quality of the permeable block and providing basic data to improve the quality and construction defect of the permeable block pavement in accordance with the continuously increasing demand of the permeable block. METHODS : In this study, we evaluated the current quality standard suitability of nine products to evaluate the current quality level of domestic production permeable blocks. The evaluation items were evaluated for surface layer thickness, block dimension, strength, and permeability coefficient, and the Korea Standard suitability for these evaluation items was analyzed. In addition, a three-dimensional finite element analysis was conducted to determine the effect of vehicle load on the deformation of block pavement structure. RESULTS : The results demonstrated that the surface layer (colored layer) thicknesses of domestically produced permeable block products were different according to the quality standards, and the dimensions were evaluated to be excellent for domestic permeable blocks currently being produced and delivered. In addition, the strength and permeability coefficient evaluation result demonstrated that all products meet the strength and permeability coefficient quality standards, but the correlation between these strengths and permeability coefficients is not high. The quality standard of strength and permeability coefficients is evaluated as being sufficiently achieved by domestic production technology. CONCLUSIONS: The intensity and permeability coefficients measured in this study were in line with the quality standards; however, the variable coefficient was found to have a significant difference in the quality control level from a maximum of 26% to a minimum 1.7%.