선박 및 교량 구조물은 일종의 길이가 긴 박스형 구조로서 수직 굽힘 모멘트에 대한 저항력이 설계의 주요 인자이다. 특히 선박 거더는 반복적으로 불규칙적인 파랑하중에 장시간 노출되어 있기 때문에 구조부재의 연속 붕괴 거동을 정확하게 예측하는 것이 무엇보다 도 중요하다. 본 논문에서는 순수 휨모멘트를 받는 박스거더의 하중 변화에 따른 좌굴을 포함한 소성 붕괴 거동을 수치해석적 방법을 이용 하여 분석하였다. 분석대상은 Gordo 실험에서 사용한 세 가지 박스거더로 선정하였다. 구조강도 실험 결과와 비선형 유한요소해석에 의한 결과를 비교하여 차이가 발생하는 원인에 대해서 고찰하였다. 본 논문에서는 카본스틸 재료의 제작 시 필연적으로 사용하는 용접열에 의한 초기 처짐의 영향을 반영하기 위하여 전체와 국부적인 처짐 형상의 조합을 제안하였고, 이 결과는 실험 결과와 거동 및 최종강도 추정율이 7% 이내에서 잘 일치하고 있었다. 논문에서 검토한 절차 및 초기 처짐 구성에 대한 내용은 향후 유사 구조물의 최종강도를 분석하는데 좋 은 지침으로 사용할 수 있다.

Various linear system solvers with multi-physics analysis schemes are compared focusing on the near-field region considering thermal-hydraulic-chemical (THC) coupled multi-physics phenomena. APro, developed at KAERI for total system performance assessment (TSPA), performs a finite element analysis with COMSOL, for which the various combinations of linear system solvers and multi-physics analysis schemes should to be compared. The KBS-3 type disposal system proposed by Sweden is set as the target system and the near-field region, which accounts for most of the computational burden is considered. For comparison of numerical analysis methods, the computing time and memory requirement are the main concerns and thus the simulation time is set up to one year. With a single deposition hole problem, PARDISO and GMRESSSOR are selected as representative direct and iterative solvers respectively. The performance of representative linear system solvers is then examined through a problem with an increasing number of deposition holes and the GMRES-SSOR solver with a segregated scheme shows the best performance with respect to the computing time and memory requirement. The results of the comparative analysis are expected to provide a good guideline to choose better numerical analysis methods for TSPA.

The fabrication of waste forms with high thermal and structural stability is an essential technology for the safe management and disposal of radioactive wastes. In particular, the thermal characteristics of waste forms containing high heat-generating nuclides such as Cs and Sr can be used for the optimized design of the waste form to secure its thermal safety, and they also provide basic design data for the safe management of canisters, storage systems, and repositories. The Korea Atomic Energy Research Institute is actively developing processes and equipment for fabricating various types of high-level wastes into a stable glass or ceramic waste form. In previous research related to the thermal analysis of the waste form, a relatively simple analysis was performed by using the analytic solution of the one-dimensional steady-state heat conduction equation considering the decay heat properties of the waste. As a specific application study, the optimized diameter of the cylindrical glass waste form was proposed by evaluating the centerline temperature of the waste form. In this study, we extended previous research by introducing a more complicated model, and the main results are summarized as follows. First, an analytical solution was derived by applying the temperaturedependent thermal conductivity expressed in the general form of polynomial function to the onedimensional heat conduction problem previously studied. Second, the two-dimensional axisymmetric steady-state heat conduction problem with a more realistic cylinder model with finite length was modeled and solved by using the finite element method via Matlab’s PDE (partial differential equation) toolbox. Third, thermal analysis was performed on the SrTiO3 waste form, selected as a stable form of strontium nuclide, using the developed analytical and numerical methods. The differences in the temperature distribution and computation time were evaluated through a comparative study of both solutions. Although the problem considered in this study could easily be solved by using commercial CFD software such as ANSYS or SolidWorks, a code-based program was developed to facilitate parametric design study in conjunction with optimization algorithms. The analysis results could be used to evaluate the thermal stability of waste form and to optimize the shape and size of the waste form in consideration of the design constraints of storage systems or repositories.

The Korean stow net is a fishing method that utilizes the changing direction of the net entrance with the tidal current. This study attempted to obtain basic data from the recent offshore stow net fisheries to improve the gear by analyzing the dynamic behavior of the nets affected by current speed and direction using computer simulations. A numerical calculation was performed at a current speed of 0.5 knot between 2.5 knot at each 0.5 knot. The time taken for the gear opening was the longest from 0.5 knot at 1,500 seconds and the shortest from 2.5 knot at 450 seconds in the simulations. In all cases, the net width and tension at net deployment gradually decreased as the current speed decreased. However, the net height tended to increase inversely proportional to the current speed. During the net rotation, the net height was maintained at all cases. The net width and tension fluctuated, but the regularity was very low. In this study, the calculated simulation data showed that the opening efficiency decreased proportional to the current speed. The opening efficiency is related to the catching efficiency; therefore, it is necessary to improve the gear to enhance its opening efficiency.

본 연구에서는 고체추진기관의 2차원 축대칭 FSI 해석에서 CSS 및 ISS 기법의 수치 안정성을 고찰하였다. 이를 위하여 CSS 및 ISS 기법을 2차원 축대칭 FSI 수치해석 알고리즘에 구현한 프로그램을 작성하고, 이를 ACM 및 BCM 고체추진기관의 복합거동 해석에 사용하였다. 해석 결과들을 비교 분석하여 ISS 기법이 고체추진기관 FSI 해석의 수치 안정성 개선에 효과적인지 검토하였다. 연구결과, ISS 기법을 적용한 FSI 해석은 시스템 시간간격이 작아질수록 수치적 수렴성을 보이며, CSS 기법과 다르게 시간이 진행되어도 수치해의 진동이 발산하지 않는 것을 확인할 수 있었다. 이를 통하여 ISS 기법을 사용하면 ACM 및 BCM의 FSI 해석에 CSS 기법을 이용할 시 나타나는 수치 불안정성을 개선할 수 있음을 확인하였다.

In this study, numerical method was used to assess technical properties and improve the Vietnamese tuna purse seine. Thedata were extracted from the two national level projects. The study results showed that average lead-line sinking speed reached 0.139 m/s and 0.143 m/s and maximum sinking depth was 61.6 m and 65.8 m for The gears 2003 and 2014 respectively. The maximum tension on ring line of The gear 2003 was 4,742 kgf and 2014 was 4,219 kgf. The improved tuna purse seines I, III and IV showed similar sinking speed results with 0.220 m/s, 0.219 m/s and 0.219 m/s respectively. The average lead-line sinking speed of the improved gear II was lowest with 0.215 m/s. The maximum lead-line sinking depth of the four improved gears I, II, III and IV were 116 m, 112 m, 115 m and 114.9 m respectively. Maximum tension on ring line of the improved gears I, II, III and IV were 5,657 kgf, 5,406 kgf, 5,645 kgf and 5,654 kgf respectively. The improved tuna purse seine IV is the most suitable for Vietnamese tuna purse seine fishery, Which corresponds with tuna purse seiner scale and its fishing supporting equipment at the present.

Fuel consumption in fisheries is a primary concern due to environmental effects and costs to fishermen. Much research has been carried out to reduce the fuel consumption related to fishing operations. The fuel consumption of fishing gear during fishing operation is generally related to hydrodynamic resistance on the gear. This research demonstrates a new approach using numerical methods to reduce fuel consumption. By designing the fishing gear using drawing software, the whole and partial resistance force on the gear can be calculated as a result of simulations. The simulation results will suggest suitable materials or gear structure for reducing the hydrodynamic forces on the gear while maintaining the performance of the gear. This research will helpful to reduce the CO2 emissions from fishing operations and lead to reduce fishing costs due to fuel savings.

SPH is the shorthand for Smoothed Particle Hydrodynamics. This method is a Lagrangian method which means that it involves following the motion of elements of fluid. These elements have the characteristics of particles and the method is called a particle method. A useful review of SPH (Monaghan 1992) gives the basic technique and how it can be applied to numerous problems relevant to astrophysics. You can get some basic SPH programs from http) /www.maths.monash.edu.au/jjm/sphlect In the present lecture I will assume that the student has studied this review and therefore understands the basic principles. In today's lecture I plan to approach the equations from a different perspective by using a variational principle.

The BINSYN program package, recently expanded to calculate synthetic spectra of cataclysmic variables, is being further extended to include synthetic photometry of ordinary binary stars in addition to binary stars with optically thick accretion disks. The package includes a capability for differentials correction optimization of eclipsing binary systems using synthetic photometry.