국내 고속도로의 본선차로 포장은 시공비용이 저렴한 줄눈 콘크리트 포장을 주로 시공하였으나, 최근 유지보수비용이 증가함에 따 라 유지관리비용이 저렴하고 공용성이 뛰어난 연속철근 콘크리트 포장을 확대 적용하고 있는 추세이다. 그러나 본선차로가 연속철근 콘크리트 포장으로 시공될 때 접속차로의 포장은 대부분 줄눈 콘크리트 포장으로 시공하고 있어 서로 다른 포장 형식이 접속함으로 인해 거동 차이가 발생하여 접속부에서 파손이 발생하기도 한다. 따라서 본 연구에서는 본선차로 연속철근 콘크리트 포장과 접속차로 줄눈 콘크리트 포장을 시공할 경우 줄눈 간격에 따른 접속차로 줄눈 콘크리트 포장의 응력 특성을 분석하기 위하여 유한요소해석 프 로그램을 이용하여 구조해석을 수행하였다. 줄눈 간격별로 줄눈 콘크리트 포장의 해석모델을 구성하였으며 환경하중인 선형수직온도 경사와 온도하강, 그리고 선형수직온도경사와 온도하강을 동시에 적용하여 해석을 실시하였다. 구조해석 결과, 모든 온도조건에서 줄 눈 간격이 좁아질수록 슬래브와 타이바의 응력이 감소하는 것으로 나타났다.

본 연구는 2011년에 개발된 한국형 포장설계법(KPRP)이 국내 도로포장 분야에서 어떻게 활용되고 있는지를 조사하며, 특히 JCP(적층 콘크리트 포장) 설계에 중점을 두고 다양한 해외 포장설계 프로그램과의 비교를 수행하였다. 이를 위해 AASHOTO Ware와 같은 국제적으로 인정받고 빈번히 활용되는 해외 프로그램을 선택하여 두 프로그램 간의 차이점을 파악하고자 했다. 비교 대상으로 선정된 AASHOTO Ware는 미국에서 개발된 프로그램으로, 차량 분류 및 기후데이터 활용과 관련하여 KPRP와는 다른 특징을 보인다. AASHOTO Ware는 차량을 16종으로 분류하는 반면, KPRP는 12종으 로 분류하며, 특히 화물차량에 대한 상세한 분류 기준을 가지고 있다. 또한, AASHOTO Ware는 실시간 기후데이터를 인터넷 기반으로 활용하는 반면, KPRP는 기상대에서 축적한 데이터를 사용한다. 두 프로그램 간의 Input 값은 기후데이 터와 교통량 데이터 중 차량 분류를 중심으로 비교하였다. 향후에는 AASHOTO Ware의 설계로직을 분석하여 더욱 세 밀한 비교를 진행하고, 두 프로그램의 설계 전이함수와 로직을 분석하여 KPRP 프로그램의 발전에 기여하는 것이 이 연 구의 최종 목표이다. AASHOTO Ware의 유연한 최종IRI값 설정과 상세한 차량 분류 기준은 KPRP의 발전 가능성을 탐 구하는 데 중요한 지표로 활용될 것으로 예상된다.

PURPOSES : The purpose of this study is to provide basic data to improve the service life of asphalt pavement using basalt aggregate in Jeju Island by evaluating the performance of asphalt pavement through analysis of material and structural aspects. METHODS : To evaluate the performance of Jeju Island's asphalt pavement, cracks, permanent deformation, and longitudinal roughness were analyzed for the Aejo-ro road, which has high traffic and frequent premature damage. Cores were collected from Aejo-ro sections in good condition and damaged condition, and the physical properties of each layer were compared and analyzed. In addition, plate cores were collected from two sections with severe damage and the cause of pavement damage was analyzed in detail. RESULTS : About 45% of the collected cores suffered damage such as layer separation and damage to the lower layer. The asphalt content of surface layer in the damaged section was found to be 1.1% lower on average than that in the good condition section, and the mix gradations generally satisfied the standards. The density difference between the cores of each layer was found to be quite large, and the air voids was found to be at a high level. CONCLUSIONS : Test results on the cores showed that, considering the high absorption ratio of basalt aggregate, the asphalt content was generally low, and the high air voids of the pavement was believed to have had a significant impact on damage. High air voids in asphalt pavement can be caused by poor mixture itself, poor construction management, or a combination of the two factors. Additionally, the separation of each layer is believed to be the cause of premature failure of asphalt pavement.

PURPOSES : This study is aimed to economic analysis of the ferronickel slag pavement method carried out to suggest the necessity of developing ferronickel slag pavement technology. METHODS : A life cycle cost analysis of the application of the Ferronickel Slag pavement method and the cutting + overlay pavement method was performed to compare the economic indicators and greenhouse gas emissions for each pavement method. RESULTS : As a result of the analysis, regardless of the Ferronickel Slag mixing rate, if the common performance of the Ferronickel Slag pavement method is the same or superior to the existing pavement method, it is more economical than the existing pavement method. Furthermore, the lower the maintenance cost of the Ferronickel Slag pavement method, the higher the economic feasibility due to the high Ferronickel Slag mixing rate. Greenhouse gas emissions can be reduced from at least 9% to up to 53% through the application of the Ferronickel Slag pavement method, except for some scenario analysis results. CONCLUSIONS : This study provided that the Ferronickel Slag pavement method was superior to the existing pavement method in terms of economic and environmental aspects. Therefore, it was found that the objective justification of developing road pavement technology using Ferronickel Slag was secured.

PURPOSES : The evaluation of the low-temperature performance of an asphalt mixture is crucial for mitigating transverse thermal cracking and preventing traffic accidents on expressways. Engineers in pavement agencies must identify and verify the pavement sections that require urgent management. In early 2000, the research division of the Korea Expressway Corporation developed a three-dimensional (3D) pavement condition monitoring profiler vehicle (3DPM) and an advanced infographic (AIG) highway pavement management system computer program. Owing to these efforts, the management of the entire expressway network has become more precise, effective, and efficient. However, current 3DPM and AIG technologies focus only on the pavement surface and not on the entire pavement layer. Over the years, along with monitoring, further strengthening and verification of the feasibility of current 3DPM and AIG technologies by performing extensive mechanical tests and data analyses have been recommended. METHODS : First, the pavement section that required urgent care was selected using the 3DPM and AIG approaches. Second, asphalt mixture cores were acquired from the specified section, and a low-temperature fracture test, semi- circular bending (SCB) test, was performed. The mechanical parameters, energy-release rate, and fracture toughness were computed and compared. RESULTS : As expected, the asphalt mixture cores acquired from the specified pavement section ( poor condition – bad section) exhibited negative fracture performances compared to the control section (good section). CONCLUSIONS : The current 3DPM and AIG approaches in KEC can successfully evaluate and analyze selected pavement conditions. However, more extensive experimental studies and mathematical analyses are required to further strengthen and upgrade current pavement analysis approaches.

PURPOSES : This study aims to understand the effect of defective dowel bar installation on jointed concrete pavement (JCP), which can cause joint freezing, spalling, cracking, and faulting and finally shorten the lifespan of the pavement. METHODS : A comprehensive field survey was undertaken at an expressway construction site in South Korea to assess dowel bar installation conditions. In addition, finite element (FE) analysis was used to simulate JCP behavior with both vertical and horizontal dowel misalignments. Different temperature conditions, including a change of -55 °C and gradient of -0.1 °C/mm, were integrated into the FE model to examine horizontal slab contraction and simultaneous slab curling. RESULTS : The analysis revealed pronounced slab behaviors under specific temperature changes, particularly when combined with dowel misalignments. The simultaneous effects of horizontal contraction and slab curling owing to temperature changes and gradients became more evident in the presence of dowel misalignments. CONCLUSIONS : The results confirmed that dowel bar misalignment considerably affected the behavior of the JCP, thereby emphasizing the importance of the proper installation of dowel bars.

PURPOSES : The purpose of this study was to evaluate the common performance of asphalt pavements, determine the timing of preventive maintenance, and determine the optimal timing of application of the preventive maintenance methods by analyzing PMS data. METHODS : Using PMS data on asphalt pavement performance on highways, we derived the major damage factors and evaluated them according to the public period and traffic level. Among the factors evaluated, we determined those that could be improved by preventive maintenance, calculated the amount of change annually, and derived the timing of the application of the preventive maintenance method through correlation analysis. RESULTS : Among highway PMS data factors, crack variation was found to affect preventive maintenance, which increased rapidly after five years of performance. Traffic analysis showed that changes increased rapidly in the fifth, sixth, and seventh years when AADT exceeded 20,000, exceeded 10,000, and was under 10,000, respectively. Analysis of the amount of crack variation according to the pavement type showed that crack variation increased rapidly in the overlay section compared to the general AP section. CONCLUSIONS : Crack variation is the performance factor that was expected to be effective in preventive maintenance, and the PMS data showed that the initial application time of the preventive maintenance method varied by one year, depending on the traffic volume.

PURPOSES : In this paper, problems and improvements in pavement marking standards are proposed as a result of the analysis of domestic/foreign standards and field data. METHODS : In this study, the US FHWA and all state standards were analyzed and domestic pavement marking standards were compared and analyzed. In addition, national highway marking test data, namely the Yeoncheon Test-Bed data, and data from Hawkins et al. (2015) were analyzed. Based on this, problems and improvements in the Korean pavement marking standards are proposed. RESULTS : As a result of literature and field data analysis, various problems were found in the Road Traffic Act and National Police Agency manual. In this standard, there is no definition of Qd; the RD reference value is set too low; and the RW and RR reference values are difficult to be considered reasonable values. CONCLUSIONS : There is an aspect in which the standard items and values of pavement markings are set under some policy judgment. Therefore, it is necessary to properly revise the standards, considering technical and economic aspects.

PURPOSES : The objective of this study was to evaluate the effectiveness of dust removal by dust removal vehicles by the measuring dust load and PM10 concentrations on the sidewalks of block pavements. METHODS : Field experiments were conducted to determine a dust removal method suitable for the sidewalk conditions, as identified through a literature review. Data collection was followed by the evaluation of the sidewalk dust load with removal vehicles and analysis of the PM10 content within a service road. Moreover, an economic analysis was conducted based on the social costs of dust reduction. RESULTS : When cleaning a sidewalk block by spraying water, the contaminants in small gaps in the block pavement could be reduced, providing a potential solution to void clogging. The dust on the surface of the sidewalk was suspended from a paved road with a high level of traffic volume. Using sidewalk dust removal vehicles with sweeping, spraying water, and inhalation reduced the dust load and PM10 contents by more than 2 and 0.07g/m2, respectively. CONCLUSIONS : According to the economic analysis of the development of dust removal vehicles for sidewalks, the cost-benefit analysis method shows an input effect of 0.4, but if the reduction amount of fine particles such as PM2.5, further experiments are necessary to address the atmospheric fine dust concentrations resulting from cleaning sidewalk block pavements.

PURPOSES : The increasing heat wave warnings during the summer season in Korea have significant impacts on daily life and industry as a whole, especially in urban areas (such as areas with asphalt and sidewalk pavements). Heat waves directly affect urban heat island and heat dome phenomena. Various urban temperature reduction measures are being discussed to reduce urban heat islands and heat dome phenomena and to improve citizen safety against summer heat waves; suggestions include thermal packaging, rooftop greening, and expansion of vegetation areas. There is a lack of analysis on the methodology for increasing the road spraying effect during summer heat waves (e.g., there is no systematic engineering study on the effect from reducing the temperature of the road spraying during a heat wave in the city) and on the types of road pavements in the city. In addition, as the asphalt pavements of roadways and block pavements installed in sidewalks account for a considerable portion of all pavements, this study provides a more systematic and scientific approach and procedures for reducing temperatures through road spraying in the city by tracking the effects of heat waves. METHODS : In this preliminary experiment, four types of road pavement materials were selected as test specimens: asphalt test specimens (AP- 300 mm × 300 mm × 50 mm), concrete test specimens (CP-300 mm × 300 mm × 50 mm), impermeable blocks (IB-200 mm × 200 mm × 60 mm), and self-permeable blocks (PB-200 mm × 200 mm × 60 mm). As a test method to evaluate the size and duration of each spray effect package type, the surface temperature of each specimen was measured using thermal imaging cameras every 20 min after spraying at the maximum temperature point of each specimen, and the average surface temperature was analyzed based on the collected temperature data. In addition, to conduct a quantitative analysis of the effect of reducing the surface temperature of road pavements by road spraying in summer, field tests were conducted on asphalt roads and watertight blocks for sidewalks. RESULTS : As a result of the comparative analysis of the spray effect under a 36 ℃ air temperature based on a heat wave warning, the surface temperatures were, from high to low, the asphalt (68.8 ℃), concrete (59.1 ℃), impermeable block (57.3 ℃), and permeable block (58.7 ℃). The asphalt pavement had the greatest effect on the heat island and heat dome phenomena. From measuring the temperature reduction effect and sustainability of each type of road pavement, the surface temperature reduction effects were ranked in the following order: water-permeable block (Δ18.0 ℃), asphalt test piece (Δ17.5 ℃), concrete test piece (Δ12.2 ℃), and water-permeable block (over 240 min). In the report pitching block, the average road surface temperature reduction between the pore recovery and treatment was expected to continue to decrease by approximately -4.3 ℃ on the day of work and approximately -2.4 ℃ on the next day. The expected effect of the temperature reduction owing to simple spraying on the surface of the pore block was evaluated to be limited to the day. CONCLUSIONS : In the road spray effect analysis conducted on the common asphalt road, there was a slight difference in the initial temperature reduction size as the test specimen was measured, but the surface temperature difference between the non-spray section and spray section tended to be approximately Δ3°C after 140 minutes of spraying. Therefore, it was determined that the asphalt pavement temperature reduction plan through road spraying in urban areas in summer would be the most effective if it was repeated twice or more in an hour (between 13:00 and 14:00) on the day of the heat wave.