The development of separation method of radioactive tritium is imperative for treating tritiumcontaminated water originating from nuclear facilities. Polymer electrolyte membrane electrolysis technology represents a promising alternative to conventional alkaline electrolysis for tritium enrichment. Nevertheless, there has been limited research conducted thus far on the composition of membrane electrode assemblies (MEAs) specifically optimized for tritium separation, as well as the methods used for their fabrication. In this study, we conducted an investigation aimed at optimizing MEAs specifically tailored for tritium separation. Our approach involved the systematic variation of MEA components, including the anode, cathode, porous transport layer, and electrode formation method. The water electrolysis efficiency and the H/D separation factor in deuterated water (1%) were evaluated with respect to both the preparation method and the composition of the MEA. To assess the long-term stability of the MEAs, changes in cell voltage, resistance, and the active electrode area were analyzed using impedance analysis and cyclic voltammetry. Furthermore, we examined H/D separation factor both before and after degradation. The results showed that MEAs with different anode/cathode configurations and electrode formation methods improved the electrolysis efficiency compared to commercial MEAs. In addition, the degree of change in the resistance value was also different depending on the electrode formation method, indicating that the electrode formation method has a significant impact on the stability of the electrolysis system. Therefore, the study showed that the efficiency and long-term stability of the water electrolzer can be improved by optimizing the MEA fabrication method.

When decommissioning of nuclear facilities happens, large amounts of radioactive wastes are released. Because costs of nuclear decommissioning are enormous, effective and economical decontamination technologies are needed to remove radioactive wastes. During NPP operation, corrosion product called Chalk River Unidentified Deposits (CRUD) is generated. CRUD is an accumulation of substances and corrosion products consisting of dissolved ions or solid particles such as Ni, Fe, and Co on the surface of the NPP fuel rod coating. CRUD is slowly eroded by the circulation of hot pressurized water and later deposits on the fuel rod cladding or external housing, thereby reducing heat production by the nuclear fuel. Decontamination of radiologically contaminated metals must be performed before disposal, and several methods for decontaminating CRUD are being studied in many countries. Decontamination technology is an alternative to reducing human body covering and reducing radioactive waste disposal costs, and much research and development has been conducted to date. Currently, the importance of decontamination is emerging as the amount of waste stored in radioactive waste storage is close to saturation, and the amount of radioactive waste generated must be minimized through active decontamination. In this study, a preliminary study was conducted on the removal of CRUD by multiple membrane in an electro-kinetic process using an electrochemicalbased decontamination method. Preliminary research to develop a technology to electrochemically remove CRUD by using a self-produced electrochemical cell to check the pH change over time of the CRUD cell according to voltage, electrolyte, membrane and pH change.

Heavy metal wastewater containing cobalt (Co2+) has received more attention as an environment issue, which is released from electroplating processes, battery materials industries, nuclear power plants, etc. Especially, cobalt exposed to high-temperature and high-pressure environment during the operation of a nuclear power plant to form corrosion products and forming a chalk river unidentified deposit (CURD) along with radioactive materials generated in cooling water pipes. Cobalt present in the oxide film is mainly Co-60, which emits radiation and causes increased radiation exposure to workers, and efficient management is essential. In this study, we demonstrated the performance of copper hexacyanoferrate (CuHCF) electrodes in a capacitive deionization (CDI) system for Co2+ ions removal. The structure and chemical status of CuHCF used as an electrode material were characterized, and electrochemical properties were evaluated. This study showed that Co2+ ions could be efficiently removed in aqueous solutions using CuHCF electrodes. It has been experimentally shown that the ion removal mechanism is driven by the insertion of Co2+ ions within the CuHCF lattice channels. The deionization capacities in 20 and 50 mg-Co2+ L-1 aqueous solutions were 141.62 and 156.85 mg g-1, respectively, and the corresponding charge efficiencies (Λ) were 0.55 and 0.68, respectively. Thus, we suggest that an electrochemically driven process using CuHCF can usefully remove Co2+ ions from wastewater.

Kori Unit 1, pressurized water reactor, is the Korea’s first commercial nuclear power plant. It successfully generated electricity for a period of 30 years, commencing from April 19, 1978. Following its approval for continued operation in 2008, Kori Unit 1 continued to operate for an additional 9 years, resulting in a total operational period of 39 years. On June 18, 2017, Kori Unit 1 was permanently shut down. Since then, Korea is actively preparing for the decommissioning of nuclear power plant. During the decommissioning of a nuclear power plant, the heavy components such as reactor, steam generator, pressurizer, reactor coolant pump located in the containment building should be taken out of the containment building. To take out heavy components from the containment building, pipes connected to heavy component should be cut. There are numerous pipes connected to the heavy component, each with varying dimensions and material. Each pipe has a different level of contamination depending on its use. In this study, optimal cutting method of pipe connected to steam generator, one of the heavy components of nuclear power plant, is proposed during the decommissioning of Kori unit 1. In case of pipe connected to Kori unit 1 steam generator, material is stainless steel or carbon steel. These pipes have varying inner diameter, ranging from 0.6 cm to 74 cm, and thickness ranging from 0.15 cm to 7.1 cm. These pipes are classified as low and intermediate level waste (LILW) or very low level waste (VLLW). Because characteristics of pipes are different, each pipe optimal cutting methods are proposed differently considering material, dimension, contamination level, cutting cost, cutting time, and the management of secondary waste. As a result, the cutting method for pipe of reactor coolant system is selected to orbital cutting. The cutting method of main steam pipe and main feedwater pipe is selected to oxygen cutting. In case of other small pipes, cutting method is selected to circular saw.

In nuclear power plant (NPP) decommissioning, ventilation and purification of the building atmosphere are important to create a working environment, ensure worker safety, and prevent the release of gaseous radioactive materials into the environment. The heating, ventilation, and air conditioning (HVAC) system of each building is maintained, modified, or newly installed. In this study, based on APR1400, operation strategies were presented in case of ventilation abnormalities in the reactor containment building (RCB), where highly radioactive particles and high dust are most frequently generated during NPP decommissioning. For research, it was assumed that the entire RCB atmospheric ventilation during decommissioning would use the RCB purge system of the existing NPP and perform continuous ventilation. Additionally, it is assumed that areas where high radiation particles and high dust occur locally, such as reactor containers or internal segments, are sealed with tents and purified using a HEFA filter of a temporary portable HVAC, and a exhaust flow path is connected to the discharge duct of the existing RCB purge system. The possibility of abnormal occurrence was largely divided into two cases. First, when large amounts of uncontrolled pollutants are released into the atmosphere inside the RCB, discharge to the environment is stopped manually or automatically by a modified engineered safety function activation signal (ESFAS). Afterwards, the RCB purge system should be operated in recirculation mode to sufficiently purify the RCB atmosphere with a HEPA filter. Second, when the first train of the low volume purge system is not running due to a failure, standby train should be operated. If both low volume purge trains fail, a high volume purge system is used. Intermittent purge operation is preferred due to large capacity during high volume purge operation. In cases where it is not possible to operate all purge systems due to common issues such as power supply, atmospheric sampling is performed to determine whether to proceed with the work inside RCB.

After the major radioactivation structures (RPV, Core, SG, etc.) due to neutron irradiation from the nuclear fuel in the reactor are permanently shut down, numerous nuclides that emit alpha-rays, beta-rays, gamma-rays, etc. exist within the radioactive structures. In this study, nuclides were selected to evaluate the source term for worker exposure management (external exposure) at the time of decommissioning. The selection of nuclides was derived by sequentially considering the four steps. In the first stage, the classification of isotopes of major nuclides generated from the radiation of fission products, neutron-radiated products, coolant-induced corrosion products, and other impurities was considered as a step to select evaluation nuclides in major primary system structures. As a second step, in order to select the major radionuclides to be considered at the time of decommissioning, it is necessary to select the nuclides considering their half-life. Considering this, nuclides that were less than 5 years after permanent suspension were excluded. As a third step, since the purpose of reducing worker exposure during decommissioning is significant, nuclides that emit gamma rays when decaying were selected. As a final step, it is a material made by radiation from the fuel rod of the reactor and is often a fission product found in the event of a Severe accident at a nuclear power plant, and is excluded from the nuclide for evaluation at the time of decommissioning is excluded. The final selected Co-60 is a nuclide that emits high-energy gamma rays and was classified as a major nuclide that affects the reduction of radiation exposure to decommissioning workers. In the future, based on the nuclide selection results derived from this study, we plan to study the evaluation of worker radiation exposure from crud to decommissioning workers by deriving evaluation results of crud and radioactive source terms within the reactor core.

Carbon 14 (14C) is radioactive isotope of carbon which emits beta ray with long half-life (5730±30 years). Since the 14C is significantly hazardous for human being, the appropriate process to treat 14C is necessary. From the nuclear power plant, the ion exchange resin, graphite, and activated carbon are the main source of 14C. During the effort to reduce the volume of those wastes, the 14C is inevitably occurred as carbon dioxide (CO2) form, so called 14CO2. Thus, the development of technology to permanently capture and safely dispose 14CO2 is required. In this presentation, we introduce the decommissioning technology ranging from 14CO2 capture to solidification. First, the new class of glass adsorbent is developed which can irreversibly capture CO2 even under mild conditions. This material promotes the dissolution of alkaline earth ions due to the unstable glass structure. Then, the physical and chemical optimization of glass adsorbent enhances the performance of CO2 capture. Further, room temperature geopolymeric solidification is also performed to safely dispose 14C without any potential release.

Kori Unit 1 nuclear power plant is a pressurized water reactor type with an output of 587 Mwe, which was permanently shut down on June 18, 2017. Currently, the final decommissioning plan (FDP) has been submitted and review is in progress. Once the FDP is approved, it is expected that dismantling will begin with the secondary system, and dismantling work on the primary system of Kori Unit 1 will begin after the spent nuclear fuel is taken out. It is expected that the space where the secondary system has been dismantled can be used as a temporary storage place, and the entire dismantling schedule is expected to proceed without delay. The main equipment of the secondary system is large and heavy. The rotating parts is connected to a single axis with a length of about 40 meters, and is complexly installed over three floors, making accessibility very difficult. A large pipe several kilometers long that supplies various fluids to the secondary system is installed hanging from the ceiling using a hanger between the main devices, and the outer diameter of the pipe is wrapped with insulation material to keep warm. In nuclear secondary system decommissioning, it is very important to check for radiation contamination, establish and implement countermeasures, and predict and manage safety and environmental risks that may occur when cutting and dismantling large heavy objects. So we plan to evaluate the radiation contamination characteristics of the secondary system using ISOCS (In- Situ Object Counting System) to check for possible radioactive contamination. According to the characteristics results, decommissioning plans and methods for safe dismantling by workers were studied. In addition, we conducted research on how to safely dismantle the secondary system in terms of industrial safety, such as asbestos, cutting and handling of heavy materials and so on. This study proposes a safe decommissioning method for various risks that may occur when dismantling the secondary system of Kori Unit 1 nuclear power plant.

The domestic Pressurized Heavy Water Reactor (PWHR) nuclear power plant, Wolsong Unit 1, was permanently shut down on December 24, 2019. However, research on decommissioning has mainly focused on Pressurized Water Reactors (PWRs), with a notable absence of both domestic and international experience in the decommissioning of PHWRs. If proper business management such as radiation safety and waste is not performed, it can lead to increased business risks and costs in decommissioning. Therefore, the assessment of waste volume and cost, which provide fundamental data for the nuclear decommissioning process, is a crucial technical requirement before initiating the actual decommissioning of Wolsong Unit 1. Decommissioning radiation-contaminated structures and facilities presents significant challenges due to high radiation levels, making it difficult for workers to access these areas. Therefore, technology development should precede decommissioning process assessments and safety evaluations, facilitating the derivation of optimal decommissioning procedures and ensuring worker safety while enhancing the efficiency of decommissioning operations. In this study, we have developed a program to estimate decommissioning waste amounts for PHWRs, building upon prior research on PWR decommissioning projects while accounting for the specific design characteristics of PHWRs. To evaluate the amount of radioactive waste generated during decommissioning, we considered the characteristics of radioactive waste, disposal methods, packaging container specifications, and the criteria for the transfer of radioactive waste to disposal operators. Based on the derived algorithm, we conducted a detailed design and implemented the program. The proposed program is based on 3D modeling of the decommissioning components and the calculation of the Work Difficulty Factor (WDF), which is used to determine the time weighting factors for each task. Program users can select the cutting and packaging conditions for decommissioning components, estimate waste amount based on the chosen decommissioning method, and calculate costs using time weighting factors. It can be applied not only to PHWRs, but also to PWRs and non-nuclear fields, providing a flexible tool for optimizing decommissioning process.

Derived Concentration Guideline Levels (DCGLs), which represent the residual radioactivity concentration limits, serve as the pivotal criteria for decontamination during decommissioning of nuclear power plants and are essential for license termination. The analysis of radionuclides in various media to check site-specific and radionuclide-specific DCGLs is a resource-intensive and time-consuming processes, and there are some radionuclides that are hard to analyze. In the decommissioning of the Rancho Seco nuclear power plant in the United States, a conservative approach was adopted. Potentially highly contaminated areas on the site were identified by collecting and analyzing soil samples, and radionuclides exceeding the Minimum Detectable Concentration (MDC) were selected as the potential Radionuclide of Concern (ROC), and surrogate DCGLs for hard-to-detect radionuclides were applied to soil samples. For soil samples in the Rancho Seco nuclear power plant, Cs-137 contributed more than 90% of the total radioactivity. DCGLs of the ROC were obtained using the scaling factors through analysis of Cs- 137 for a large amount of soil samples. In Korea, the scaling factor methodology has not been applied to the decommissioning of commercial nuclear power plants. An initial investigation was undertaken to assess the viability of implementing Surrogate Derived Concentration Guideline Levels (DCGLs) in the dismantling of Kori Unit 1, drawing insights from the U.S. nuclear power plant decommissioning experiences. To do this approach, the concentration ratio of radionuclides of interest to key radionuclide in contaminated soil should be known and consistent. But related information is not available at this time. So Surrogate DCGL for representative C-14, Fe-55, Ni-59, Ni-63, and Sr-90 was obtained using the scaling factors applied to radioactive waste data, specifically Decontaminated Aqueous Waste (DAW) and Spent Resin. In order to develop a reliable surrogate DCGLs the Kori Unit 1 site, it is important to analyze the radionuclides in the soil for the Kori Unit 1 decommissioning site to obtain consistent concentration ratio of the radionuclides of concern to the key radionuclides. When a the suitable DCGL is developed, it can be used for FSS planning and prior decision-making ensuring the safe and effective decommissioning of Kori Unit 1 and similar nuclear power plants.

In 2017, the permanent shutdown of Kori Unit 1 was decided, marking the initiation of preparations for the decontamination and decommissioning of Kori Unit 1. The dismantling of radiologically contaminated equipment and concrete structures such as the Reactor Vessel (RV), Reactor Vessel Internals (RVI), and the Bio shield is crucial in the nuclear decommissioning process. These components became radiologically contaminated due to nuclear fission reactions occurring in the reactor during its operational period. The RVI dismantling at Spain’s Jose Cabrera Nuclear Power Plant involved the use of mechanical saws and disk cutters to divide it into approximately 430 pieces, taking 16 months to complete. Germany’s Stade Nuclear Power Plant employed mechanical circular saws to segment their RVI into about 170 pieces, which took 30 months to accomplish. Meanwhile, the RVI at Germany’s Wurgassen Nuclear Power Plant was subdivided into approximately 1,200 pieces using a combination of mechanical saws and abrasive water jets, requiring 61 months for completion. Due to the radioactivity in Kori Unit 1’s Reactor Vessel (RV) and Reactor Vessel Internals (RVI), remote-controlled systems were developed for cutting within the cavity to reduce radiation exposure. Specialized equipment was developed for underwater cutting operations. This paper focuses on modeling related to RVI operations using the MAVRIC code. The upper and lower parts of the RVI are classified as low-level radioactive waste, while the sides of the RVI that come into contact with fuel are classified as intermediate-level radioactive waste. Therefore, the modeling presented in this paper only considers the RVI sides since the upper and lower parts have a minimal impact on radiation exposure. Accurate calculations were performed through geometric modeling and radiation dose modeling. These research findings are anticipated to contribute to enhancing the efficiency and safety of nuclear reactor decommissioning operations

When dismantling a power plant, a large amount of radioactive tanks are generated, and it is estimated that a significant amount of sludge will accumulate inside the tanks during long-term operation. In the process of dismantling a radioactive tanks, it is important to know the composition of the sludge because the sludge present inside must first be removed and then disposed of. In the case of certain tanks, it can be predicted that corrosion products generated due to system corrosion are the main cause of sludge formation. However, in the case of some tanks, it is not easy to predict the sludge composition because various dispersed particles in addition to corrosion products may be mixed with the wastewater. Even if it is collected and analyzed, the sludge composition can change significantly depending on the operation history, so the analysis results cannot be considered representative of the composition. In the case of LHST, surfactant components introduced during the washing and shower process, oil components and dispersed particles dissolved by the surfactant accumulate inside the tank, making sludge difficult to remove. In addition, even if it is removed by ultra-high pressure spraying, unexpected problems may occur in the subsequent treatment process due to the surfactant contained therein. Therefore, it is necessary to analyze in more detail the characteristics of sludge accumulated in LHST and prepare countermeasures. A test procedure was prepared to evaluate the characteristics of sludge accumulating in LHST. According to the test results, the long-term sludge accumulation tendency of the LHST is summarized as follows. ① Initially, the sludge settling speed increases slowly until a surface sludge layer is formed. ② After the surface sludge layer is formed, the sludge rapidly settles until the sludge layer becomes somewhat thicker. ③ When the sludge layer is formed to a certain extent, the sludge escape rate increases and the sludge accumulation rate decreases again. It is assumed that the sludge escape speed is closely related to the fluid flow speed in the relevant area. It is believed that the combined effect of these phenomena will determine the thickness of the sludge layer that will accumulate inside the tank, but it was not possible to evaluate how much the sludge layer would accumulate based on the experimental results alone. However, it can be assumed that significant sludge accumulation occurred in areas where fluid flow was minimal and sludge formation nuclei easily accumulates.

Tritium is radioactive isotope, emitting beta ray, released as tritiated water from nuclear power plants. Due to the danger of radioactive isotope, the appropriate separation of tritium is essentially carried out for environment and safety. Further, it is also promising material for energy production and research. The tritiated water can be treated by diverse techniques such as water distillation, cryogenic distillation, Girdler-sulfide process, and catalytic exchange. After treatment, it is more desirable to convert as gas phase for storage, comparing to liquid phase. However, achieving complete separation of hydrogen gases with very similar physical and chemical properties is significantly challenging. Thus, it is necessary to develop materials with effective separation properties in gas separation. In this presentation, we present hydrogen isotope separation in the gas phase using modified mesoporous silica. Mesoporous silica is a form of silica that is characterized by its mesoporous structure possessing pores that range from 2 to 50 nm in diameter. This material can be functionalized to selectively capture and separate molecules having specific size and affinity. Here, the silver and copper incorporated mesoporous silica was synthesized to tailor a chemical affinity quantum sieving effect, thereby providing separation efficiency in D2/H2. The adsorption quantities of H2 and D2 were determined by sorption study, and the textural properties of each mesoporous silica were analyzed using N2 physisorption. The selectivity (D2/H2) in diverse feed composition (1:1, 1:9, and 1:99 of D2/H2) was estimated by applying ideal adsorbed solution theory to predict the loading of the gas mixture on bare, Ag- and Cu-mesoporous silica based on their sorption study. Further, the performance of each mesoporous silica was evaluated in the breakthrough adsorption under 1:1 mixture of D2 and H2 at 77 K.

Heavy water primary system decontamination technology is essential to reduce worker exposure and improve safety during maintenance and decommissioning of nuclear facilities. Advanced decontamination technology development aims to secure controlled decontamination technologies that can reduce the cost of radiation exposure and dramatically reduce the amount of secondary waste generated when decontaminating large equipment and large-area facilities. We conducted a study to identify candidate corrosion inhibitors through the literature and analyze the degree of corrosion of carbon steel samples. Countries with advanced nuclear technology have developed chemical decontamination technology for the entire nuclear power generation system and applied it to the dismantling and maintenance of nuclear power plants. In the decontamination process, the corrosion oxide film must be removed. If the base metal is corroded by the decontaminant in this process, additional secondary waste is generated and treatment costs increase. Therefore, it is necessary to develop a corrosion inhibitor that inhibits the corrosion of the carbon steel base metal in the decontamination process to generate a secondary waste liquid that is favorable for waste reduction and treatment. In this presentation, a study was conducted to analyze the extent of corrosion on a carbon steel base material and identify candidate materials for corrosion inhibition testing. Samples were analyzed using optical microscopy and EPMA analysis to determine the thickness of the corroded oxide film. EPMA analysis also allowed us to map the elemental distribution of the carbon steel corrosion layer, which we plan to quantify in the future. The candidate materials for organic-based corrosion inhibitor were also selected based on their inhibition mechanism; having high electronegative elements for coordinate covalent bonding at metal surface and hydrophobic nonpolar group for preventing access of corrosive substances.The selection of candidate materials for corrosion inhibition testing was based on the mechanism of the corrosion inhibitor. Organic-based corrosion inhibitors are adsorbed by donor-acceptor interactions between metal surfaces and highly electronegative elements. Corrosion can also be inhibited by arranging hydrophobic nonpolar groups on metal surfaces in the solution direction to prevent access of corrosive substances.

As the decommissioning of domestic nuclear power plants (Gori Unit 1 and Wolseong Unit 1) becomes more visible, many research projects are being conducted to safely and economically decommissioning of domestic nuclear power plants (NPPs). After permanent shutdown, decommissioning of NNPs proceeds through decontamination, cutting of main equipment, waste disposal and site restoration stages. And various technologies are applied at each stage. In particular, remote cutting of neutron induced structures (RV, RVI, etc.) is a technology used in developed countries in the cutting stage, and remote cutting has been evaluated as a core technology for minimizing workers’ radiation exposure. Generally, remote cutting technologies are divided into mechanical/thermal/electrical cutting. Among various thermal cutting technologies, plasma arc cutting (PAC) is more economical and easily to remote control than other cutting technologies, and is also effective in cutting STS304 plates. PAC is a thermal cutting technology that melts the base material at the cutting area with a plasma arc heat source and removes melted material by blowing it out with cutting gas. The cutting quality depends on the stand-off distance and power (current), material thickness, cutting speed, etc., while double arcing will occur if the cutting conditions are not suitable. A monitoring system that can confirm double arcing during remote cutting is necessary because double arcing can reduce cutting quality, increase secondary waste (increase kerf and aerosol), and cause non-cutting. In this study, we used an ultrahigh-speed camera equipped with a band-pass filter to capture clear arc shapes, and measured voltage waveforms with a data acquisition system. We studied a monitoring method that can confirm the occurrence of double arcing by synchronizing the obtained arc shape and voltage waveform, and the effects of double arcing on the STS304 plates. The results of this study are expected to be helpful in the development of the remote cutting process using plasma arc cutting when decommissioning of domestic NPPs.

Thermal cutting processes that can be applied to dismantling nuclear power plants include oxygen cutting, plasma cutting, and laser cutting. According to the global trend, research projects are being carried out in various countries to upgrade laser cutting, and many studies are also being conducted in Korea with plans to apply laser cutting processes when dismantling nuclear power plants. However, with the current technology level of the laser cutting process, the maximum thickness that can be cut is limited to 250 mm. Therefore, in this study, a laser-oxygen hybrid cutting process was implemented by adding a laser heat source to the oxygen cutting process that can cut carbon steel with a thickness of 250 mm or more (RV, beam, column, beam, etc.) when dismantling the nuclear power plant. This has the advantage of improving the cutting speed and reducing the cutting width Kerf compared to conventional oxygen cutting. In this research, the laser-oxygen hybrid cutting process consisted of laser cutting to which Raycus’ 8 kW Fiber Laser power source was applied and oxygen cutting to which hydrogen was applied with Fuel Gas. The oxygen torch was placed perpendicular to the test piece, and the laser head was irradiated by tilting 35° to 70°. The effects of cutting directions on quality and performance were studied, and cutting paths were selected by comparing cutting results. Thereafter, it was confirmed that there is an optimal laser output power according to the cutting thickness by studying the effect on the cutting surface quality by changing only the laser output power under the same cutting conditions. The results of this study are expected to be helpful in the remote cutting process using laser-oxygen hybrid cutting when dismantling domestic nuclear power plants in the future.

The primary purpose of high temperature process of radioactive waste is to satisfy the waste acceptance criteria and volume reduction. The WAC offers the guideline of waste form fabrication process. The WAC is defined as quantitative or qualitative criteria specified by the regulatory body, or specified by and operator and approved by the regulatory body, for radioactive waste to be accepted by the operator of a repository for disposal, or by the operator of a storage facility for storage. The main objective of WAC is to protect staff and general public and environment by the containment of radioactive material, limit external radiation level, and prevent criticality. The WAC also offers systematic management of radioactive waste by standardization of waste management operations, facilitation waste tracking, ensure safe and effective operation of operating facilities, etc. Since the high temperature process for radioactive waste is considered in many countries, lots of codes and standards are considered. In many WACs, compressive strength, thermal cycle stability, radiation exposure stability, free liquid, and leachability are evaluation to understand the effect of solidified form to the disposal facility. In this paper, systematical review on waste form will be discussed. In addition, brief result of characterization of waste form will be compared.

The thermal treatment of radioactive waste attracts great attention. The thermal treatment offers lots of advantages, such as significant volume reduction, hazard reduction, increase of disposal safety, etc. There are various thermal technologies to waste. The developed technologies are calcination, incineration, melting, molten salt oxidation, plasma, pyrolysis, synroc, vitrification, etc. The off-gas treatment system is widely applied in the technologies to increase the safety and operation efficiency. The thermal treatment generates various by-product and pollutants during the process. The dust or fly ash are generated as a particulate from almost every radioactive waste. The treatment of PVC related components generates hydrogen chloride, which usually brings corrosion of facility. The treatment of rubber and spent resin generates sulfur oxide, SOx. The treatment of nitrile rubber generates nitrogen oxide, NOx. The incomplete combustion of radioactive waste usually generates carbon oxide, COx. The process temperature also affects the generation of off gas, such as NOx and/or COx. Various off gas treatment components are organized for the proper treatment of the previously mentioned materials. In this study systematical review on off gas treatment will be reported. Also, worldwide experiences and developed facility will be reported.

Tc-99 is considered as one of the major fission products in the context of disposal of spent nuclear fuel, due to the long half-life and chemical stability. In the atmospheric aqueous solutions, Tc is expected to exist in the form of TcO4 ‒ and thus is considered as an environmental concern according to its high solubility and mobility. Therefore, the development of an effective and economically viable adsorbent for aqueous Tc(VII) is imperative from the perspective of decontamination and remediation of contaminated environments. In this work, the adsorption behaviors of Re(VII), as a chemical surrogate of Tc(VII), onto the bentonites modified with two different organic cations such as hexadecyl pyridinium (HDPy) and hexadecyl trimethylammonium (HDTMA) were quantitatively analyzed and compared with each other. For the sorption experiment, adsorbents were prepared by surface modification of bentonite. Before the modification, the initial bentonite was pre-treated with 1 M NaClO4 and then reacted with HDPy or HDTMA. The modification process was performed at room temperature for 24 hours with various concentrations of organic cations, which were set to a range of 50-400% compared to the cation exchange capacity (CEC) of bentonite. After the reaction, the dried and crushed modified bentonites were filtered with the sieve with a mesh size of 63 μm. Aqueous Re(VII) solutions were prepared by dissolution of NH4ReO4 (Sigma-Aldrich) in deionized water with three different Re(VII) concentrations of 10-4M, 10-5M, and 10-6M. After that, the modified bentonite and the aqueous Re(VII) solutions were mixed at a liquid-to-solid ratio of 1 g/L. Aliquots of the samples were extracted for quantification analysis with ICP-MS after syringe filtration (pore size: 45 μm) at reaction times of 10, 50, 100, and 500 minutes. According to the results, a considerably fast adsorption reaction of Re(VII) onto all modified bentonites was observed, revealing exceptional sorption affinity of HDPy- and HDTMA-modified bentonites. For both organic cations, bentonites modified with the concentrations of organic cations ranging from 200 to 400% relative to the CEC of bentonite showed almost complete removal of aqueous Re(VII). For bentonites modified with lower concentrations of organic cations, the HDTMA presented a relatively larger sorption capacity than the HDPy. The result obtained through this study is expected to be referred to as a case study for the synthesis of cost-efficient and highly effective adsorbent material for highly mobile anionic radionuclides such as I‒ and TcO4 ‒.

Recently, BNS (Best System) developed a system for evaluation and classification of soil and concrete wastes generated from nuclear power plant decommissioning. It is composed of various modules for container loading, weight measurement, contamination evaluation, waste classification, stacking, storage and control. The contamination evaluation module of the system has two sub modules. One is for quick measurement with NaI (Tl) detector and the other is for accurate measurement with HPGe detector. The container used at the system for wastes handling has capacity of 100 kg and made of stainless steel. According to the measurement result of Co-60 and Cs-137, the waste is classified as waste for disposal or waste for clearance. Performance of the system was demonstrated using RM (Reference Material) radiation source. This year, necessity of system improvement was suggested due to revised operation requirements. So, the system should show throughput of more than 1 ton/hr and Minimum Detectable Activity (MDA) of less than 0.01 Bq/g (1/10 of criteria for regulatory clearance) for Co-60 and Cs-137. And soil waste become main target of the system. For this, the container used for soil waste handling should have capacity of 200 kg. As a result, material for the container need to be changed from stainless steel to plastic or FRP (Fiber Reinforced Plastics). And large area detector should be introduced to the system to enhance processing speed of the system. Additionally, container storage rack and conveyor system should be modified to handle 200 kg capacity container. Finally, moving path of the container will be redesigned for enhanced throughput of the system. In this paper, concept development of the system was suggested and based on that, system development will be followed.