Within the air purification system of a nuclear power plant, specific radioactive isotopes are extracted from gases through adsorption onto activated carbon. To properly dispose of used activated carbon, it is essential to determine the concentration of radioactive nuclides within it. This study discusses the application of the pyrolysis method for analyzing the concentrations of 3H and 14C in spent activated carbon. The pyrolysis was conducted using Raddec’s Pyrolyser, with adjustments made to parameters such as temperature profiles, airflow rates, sample quantities, and trapping solution volumes. The evaluation method for the pyrolysis of activated carbon to analyze 3H and 14C involved adding 3H and 14C sources to the activated carbon before use and subsequently assessing the recovery rates of the added sources in comparison to the analysis results.

Currently, non-volatile nuclides such as 94Nb, 99Tc, 90Sr, 55Fe, and 59/63Ni are used a sequential separation. In this study, we developed a separation for 99Tc and 90Sr by a carbonate precipitation. Sodium Carbonate (Na2CO3) was inserted in the aqueous sample from a Dry Active Waste (DAW) and a carbonate precipitation was produced. The precipitate is composed of di- or tri-valent element such as Co, Sr, Fe, Ni and the supernatant is composed of mono-valent element (Cs) and anion materials (ReO4 -, TcO4 -). In DAW, it was confirmed that the recovery of 90Sr (precipitate) and 99Tc (supernatant) were > 90%, respectively. The precipitate and supernatant separated by using a Sr-resin and an anion-exchange resin, respectively. The separated samples were measured by a Liquide Scintillation Counter (LSC, 90Sr) and Induced-Coupled Plasma-Mass Spectroscopy (ICPMS, 99Tc).

Bis (2-ethylhexyl)phosphoric acid (HDEHP) is a renowned extractant, favored for its affinity to selectively remove uranium via its P=O groups. We previously synthesized HDEHP-functionalized mesoporous silica microspheres for solid-phase uranium adsorption. Herein, we investigated the kinetic and isothermal behavior of uranyl ion adsorption in mesoporous silica microspheres functionalized with phosphate groups. Adsorption experiments were conducted by equilibrating 20 mg of silica samples with 50 mL of uranium solutions, with concentrations ranging from 10 to 100 mgU L−1 for isotherms and 100 mgU L−1 for kinetics. Three distinct samples were prepared with varying HDEHP to TEOS molar ratios (x = 0.16 and 0.24) and underwent hydrothermal treatment at different temperatures, resulting in distinct textural properties. Contact times spanned from 1 to 120 hours. For x = 0.16 samples, it took around 50 and 11 hours to reach equilibrium for the hydrothermally treated samples at 343 K and 373 K, respectively. Adsorbed quantities were similar (99 and 101 mg g-1, respectively), indicating consistent functional group content. This suggests that the key factor influencing uranium adsorption kinetics is pore size of the silica. The sample treated at 373 K, with a larger pore size (22.7 nm) compared to 343 K (11.5 nm), experienced less steric hindrance, allowing uranium species to diffuse more easily through the mesopores. The data confirmed the excellent fit of pseudo-second-order kinetic model (R2 > 0.999) and closely matched the experimental value, suggesting that chemisorption governs the rate-controlling step. To gain further insights into uranium adsorption behavior, we conducted an adsorption isotherm analysis at various initial concentrations under a constant pH of 4. Both the Langmuir and Freundlich isotherm models were applied, with the Langmuir model providing a superior fit. The relatively high R2 value indicated its effectiveness in describing the adsorption process, suggesting homogenous sorbate adsorption on an energetically uniform adsorbent surface via a monolayer adsorption and constant adsorption site density, without any interaction between adsorbates on adjacent sites. Remarkably, differences in surface area did not significantly impact uranium removal efficiency. This observation strongly suggests that the adsorption capacity is primarily governed by the loading amount of HDEHP and the inner-sphere complexation with the phosphoryl group (O=P). Our silica composite exhibited an impressive adsorption capacity of 133 mg g-1, surpassing the results reported in the majority of other silica literature.

The ultimate objective of deep geological repositories is to achieve complete segregation of hazardous radioactive waste from the biosphere. Thus, given the possibility of leaks in the distant future, it is crucial to evaluate the capability of clay minerals to fulfill their promising role as both engineered and natural barriers. Selenium-79, a long-lived fission product originating from uranium- 235, holds significant importance due to its high mobility resulting from the predominant anionic form of selenium. To investigate the retardation behaviors of Se(IV) in clay media by sorption, a series of batch sorption experiments were conducted. The batch samples consisted of Se(IV) ions dissolved in 0.1 M NaCl solutions, along with clay minerals including kaolinite, montmorillonite, and illite-smectite mixed layers. The pH of the samples was also varied, reflecting the shift in the predominant selenium species from selenious acid to selenite ion as the environment can shift from slightly acidic to alkaline conditions. This alteration in pH concurrently promotes the competition of hydroxide ions for Se(IV) sorption on the mineral surface as the pH increases and impedes the selective attachment of selenium. The acquired experimental data were fitted through Langmuir and Freundlich sorption isotherms. From the Freundlich fit data, the distribution coefficient values of Se(IV) for kaolinite, montmorillonite, and illite-smectite mixed layer were derived, which exhibited a clear decrease from 91, 110, 62 L/kg at a pH of 3.2 to 16, 6.3, 12 L/kg at a pH of 7.5, respectively. These values derived over the pH range provide quantitative guidance essential for the safety assessment of clay mineral barriers, contributing to a more informed site selection process for deep geological repositories.

In order to establish disposal plans for sludge, which is one of the untreated waste materials from domestic nuclear power plants, it is necessary to determine the radioactivity concentration of radioactive isotopes. In this study, we aim to evaluate the gross alpha radioactivity of sludge containing radioactive contaminants after pre-treatment, in order to assess the level of sludge waste and obtain analytical data for discussing disposal methods. Samples of sludge generated from nuclear power plants were pre-treated, solutionized, and prepared as analysis samples for evaluating the gross alpha radioactivity.

Typically, the bottom of the effluent treatment facility at a nuclear power plant contains sediment, which is low-contamination waste consisting of sludge, gravel, sand, and other materials from which radioactive contaminants have been removed. Among these sediments, sludge is an irregular solid form consisting of small particles that are coagulated together, with radioactive isotopes containing cobalt attached. Currently, there is a record of disposing of dry active waste from domestic nuclear power plants, and efforts are underway to gather basic data for the disposal of untreated waste such as sludge, spent filter, and spent resin. In particular, the classification and disposal methods of waste will be determined based on the radioactivity concentration. Therefore, plans are being made to determine the radioactivity concentration of radioactive isotopes and establish disposal plans for sludge samples. In this study, pre-treatment and solutionization were carried out for the analysis of radioactive isotopes in sludge sampels from nuclear power plants. The deviation of the gamma radioisotope analysis results was derived to obtain an optimal sample quantity that represents the sludge.

For the disposition of radioactive wastes generated from nuclear power plant, radioisotope inventory must be analyzed to determine an activity concentration of radionuclides. Radionuclides in low- and intermediate-low-level of radioactive wastes, however, can be easily classified to easyto- measure (ETM) and difficult-to-measure (DTM) nuclides. ETM nuclides are gamma emitting nuclides that is relatively easy to measure because they do not need to be destroyed for the preprocessing. On the other hands, DTM nuclides are alpha and beta emitting nuclides that need to be destroyed for the preprocessing and also need chemical separation. Currently, measurement methods for DTM nuclides are developed and in this paper measurement methods of Fe-55, Ni-59, Ni-63, Sr-90 and Tc-99 will be introduced.

Alpha activities can be used for categorization, transportation, and disposal of radioactive waste generated from the operation of nuclear facilities including nuclear power plants. In order to transport and dispose of such low- and intermediate-level radioactive waste (LILW) to the Wolsong LILW Disposal Center (WLDC) at Gyeongju, the gross alpha concentration of an individual drum should be determined according to the acceptance criteria. In addition, when the gross alpha concentration exceeds 10 Bq/g, the inventory of the comprising alpha emitters in the waste is to be identified. Gross alpha measurements using a proportional counter are usually straightforward, inexpensive, and high-throughput, so they are broadly used to assay the total alpha activity for environmental, health physics, and emergency-response assessments. However, several factors are thoughtfully considered to obtain a reliable approximate for the entire alpha emitters in a sample, which include the alpha particle energy of a particular radionuclide, the radionuclide that is used as a calibration standard, the uniformity of film in a planchet, time between sample collection and sample preparation, and time between sample preparation and counting. Korea Atomic Energy Research Institute (KAERI) have evaluated the inventory of radionuclides in low-level radioactive waste drums to send every year hundreds of them to the WLDC. In this presentation, we revisit the gross alpha measurement results of the drums transported to WLDC in the past few years and compare them with the concentrations of alpha emitters measured from alpha spectrometry and gamma spectrometry. This study offers an insight into the gross alpha measurement for radioactive waste regarding calibration source, self-absorption effect, composition of alpha emitters, etc.

To achieve permanent disposal of radioactive waste drums, the radionuclides analysis process is essential. A variety of waste types are generated through the operation of nuclear facilities, with dry active waste (DAW) being the most abundant. To perform radionuclides analysis, sample pretreatment technology is required to transform solid samples into solutions. In this study, we developed a dry ashing-microwave digestion method and secured the reliability of the analysis results through a validity evaluation. Additionally, we conducted a comparative analysis of the radioactivity of 94Nb nuclides with and without the chemical separation process, which reduced the minimum detectable activity (MDA) level by more than 65-fold for a certain sample.

To ensure the maintenance of the nuclear emergency response system, it is important to periodicaly conduct hazard assessments using up-to-date input variables. The results of this review are apllied to drills and exercises, enabling the inspection of emergency plan and response procedures. Therefore, this study aims to analyze off-site consequences according to the occurrence time of the Design Basis Accident (DBA) for the Hanaro Fuel Fabrication Facility (HFFF) by using the recent site-specific meteorological data and to review the appropriateness of urgent protective measures. MELCOR and SafeHanaro computer codes were used for radiation source-term estimation and environmental impact assessment, respectively. It was assumed that radioactive materials are released into environment for 2 hours due to the fire during the nuclear fuel sieving process. The following 12 scenarios for each occurrence time period was selected (0 am, 2 am, 4 am, 6 am, 8 am, 10 am, 12 pm, 2 pm, 4 pm, 6 pm, 8 pm, 10 pm) and the effective dose and thyroid dose in earlyand intermediate-phase were assessed. As a result, the most severe exposure-induced accident scenario is found to be as occurring at 0 am on July 15th, with the Most Exposed Individual (MEI) positioned 200 meters downwind from the facility. The committed effective dose for MEI is identified as to be 2.97E-02 mSv which has a significant margin against the IAEA's (Generic Intervention Level) GIL and (Generic Criteria) GC. During the passage of the radio-active plume, the estimated effective dose and thyroid dose due to inhalation were 2.97E-02 mSV (99.99%) and 5.06E-05 mSv (99.77%), respectively. External exposure appeared to be negligible. Meanwhile, the thyroid dose is noticeably below the criteria for decision-making for distribution of Potassium Iodide (KI). Accordingly, in order for local residents to participate in the exercise and drills, it is essential to develop scenarios considering simultaneous emergencies at multi-facilities and latenight accidents. In conclusion, this results will be used to improve the exercise plans for enhancing the nuclear or radiological emergency competencies of the KAERI.

The objective of this study is to investigate the safety awareness and effectiveness of the education and training for employees engaged in radiological emergency organization of the Korea Atomic Energy Research Institute (KAERI). In 2022, the questionnaire for the education satisfaction survey was revised to regulary evaluate the effect of edcation on perceptions of importance on emergency preparedness for nuclear research facilities. In line with, a standard questionnaire was created which covers 3 factors and 9 attributes, and the evaluation indicatior is based on a 5-point Likert scale. In 2023, the education on radiological emergency preparedness was conducted for 235 emergency staff. From May 24 to July 13, 2023, data was collected from a total of 235 emergency response personnels, including 28 new staffs and 207 maintenance staffs. Aa a result of response analysis, it was identified that education for radiological emergency response had a significant correlation with the promoting safety culture. It was found that senior emergency personnel with more years of experience are highly interested in radioactive disaster prevention and actively participate in and training. On the other hand, it was presented that new and less experienced groups tend to have a relatively high scored of the risk perception of nuclear research facilitites. Therefore, it is necessary to improve the practical curriculum in order to increase the participation of junior disaster prevention personnel in education and training, ensuring that they correctly recognize the risk of research facilities. This results are expected to be used to improve the quality of education and drills for radiological emergency response at KAERI.

The nuclear fuel that melted during the Fukushima nuclear accident in 2011 is still being cooled by water. In this process, contaminated water containing radioactive substances such as cesium and strontium is generated. The total amount of radioactive pollutants released by the natural environment due to the nuclear accident in Fukushima in 2011 is estimated to be 900 PBq, of which 10 to 37 PBq for cesium. Radioactive cesium (137Cs) is a potassium analog that exists in the water in the form of cations with similar daytime behavior and a small hydration radius and is recognized as a radioactive nuclide that has the greatest impact on the environment due to its long half-life (about 30 years), high solubility and diffusion coefficient, and gamma-ray emission. In this study, alginate beads were designed using Prussian blue, known as a material that selectively adsorbs cesium for removal and detection of cesium. To confirm the adsorption performance of the produced Prussian blue, immersion experiments were conducted using Cs standard solution, and MCNP simulations were performed by modeling 1L reservoir to conduct experiments using radioactive Cs in the future. An adsorption experiment was conducted with water containing standard cesium solution using alginate beads impregnated with Prussian blue. The adsorption experiment tested how much cesium of the same concentration was adsorbed over time. As a result, it was found that Prussian blue beads removed about 80% of cesium within 10-15 minutes. In addition, MCNP simulation was performed using a 1 L reservoir and a 3inch NaI detector to optimize the amount of Prussian blue. The results of comparing the efficiency according to the Prussian volume was shown. It showed that our designed system holds great promise for the cleanup and detection of radioactive cesium contaminated seawater around nuclear plants and/or after nuclear accidents. Thus, this work is expected to provide insights into the fundamental MCNP simulation based optimization of Prussian blue for cesium removal and this work based MCNP simulation will pave the way for various practical applications.

Korea Atomic Energy Research Institute (“KAERI”) has been developing pyroprocess technology for the sustainable use of nuclear energy and radioactive waste reduction, and is conducting design studies for a Pyroprocess Commercializing Research Facility (PCRF). High-level radioactive materials such as spent nuclear fuel, which are handled in the hot cell of the PCRF, physically change materials directly or cause chemical changes through ionization or excitation depending on the energy and types of radiation. Therefore, all facilities, including process equipment and remote handling equipment, installed into the hot cell must be evaluated for radiation hardness to be maintained in the radiological environmfent so that processes can proceed throughout the design life of the facility. In addition, as the maintenance paradigm has recently shifted from corrective maintenance to predictive maintenance, it is necessary to know in advance the condition of the equipment or facility in the radiological environment. In this study, an analysis of the radiation environment of the hot cell in the PCRF was conducted through source term, and the radiological dose impact was evaluated through the results of irradiation experiments of major components by reference data. Then, the actual dose contribution was identified through dose assessment using the MCNP code based on the pyroprocess equipment, and the radiation hardness requirements for the facility and equipment in the hot cell were derived by the above results.

The nuclear licensee must ensure that the nuclear or radiological emergency preparedness and response organization is explicitly defined and staffed with adequate numbers of competent and assessed personnel for their roles. This paper describes the responsibilities of medical and support personnel for the medical action of casualties in the event of a radiological emergency at the KAERI. Currently, there is one medical personnel (nurse) in KAERI, and a total of eight medical support personnel are designated for medical response in the event of a radiological emergency. These medical support personnel are designated as one or two of the on-site response personnel at each nuclear facility, operating as a dedicated team of A, B (4 people each). In the event of a radiological emergency, not all medical support personnel are mobilized, but members of the dedicated medical team, which includes the medical support personnel of the nuclear facility where the accident has occurred, are summoned. Medical and support personnel will first gather in the onsite operational support center (OSC)/technical support center (TSC) to prepare and stand by for the medical response to injured when a radiological emergency is declared. They should take radiation protective measures, such as wearing radiation protective clothing and dosimeters, before entering the onsite of a radiological emergency, because injuries sustained during a radiological emergency may be associated with radioactive contamination. In the event of an injury, direct medical treatment such as checking the patient’s vitals, first aid, and decontamination will be carried out by medical personnel, while support personnel are mainly responsible for contacting the transfer hospital, reporting the patient’s condition, accompanying the ambulance, filling out the emergency medical treatment record, and supporting medical personnel. In order to respond appropriately to the occurrence of injuries, we regularly conduct emergency medical supplies education and medical training for medical support personnel to strengthen their capabilities.

A new annual dose evaluation system called E-DOSE has been developed. The system is based on the methodology of the previous version, K-DOSE60, which uses the dose evaluation methods of the International Commission on Radiological Protection (ICRP-60). However, E-DOSE is coded in ABAP to be compatible with the KHNP’s enterprise resource planning (ERP) system, SAP. This allows E-DOSE to use the real-time data from SAP, which minimizes the need for user intervention. The socio-environmental data, which was previously managed by the staff of each plant sites, can now managed in the system in a centralized manner. This is a significant improvement over the previous system, as it reduces the risk of errors and makes it easier to track and manage data. The system also automatically generates the reports required by regulations. EDOSE is expected to minimize the occurrence of human errors in preparing and managing the input data. This is because the system uses the data from SAP, which is less prone to errors than manually entered data. Additionally, the automatic generation of reports reduces the risk of errors in report preparation. E-DOSE is also expected to improve work efficiency. This is because the system automates many of the tasks involved in annual dose evaluation, such as data entry, calculation, and report generation. Overall, E-DOSE is a significant improvement over the previous annual dose evaluation system. It is more efficient, accurate, and user-friendly.

When occurring at a nuclear power plant (NPP) by accidents, accurate prediction and identification of the process of radioactive material dispersing into atmosphere is important to protect public and environment. Atmosphere dispersion of radioactive materials is significantly influenced by wind direction and wind speed. The government and nuclear operator continuously monitor wind data at nuclear sites through meteorological tower to prepare for such accidents involving the release of radioactive materials. The purpose of this study is to construct wind rose diagrams at 5 NPP sites (Kori, Saewool, Wolsong, Hanbit, Hanul). Wind roses serve as invaluable tool for identifying wind patterns in each region and visualizing wind directions. This can be utilized to predict the dispersion pathway and extent range of radioactive materials carried by the wind. This program will take on the role of establishing appropriate evacuation routes or shelter locations for residents when reliable wind data is not immediately available during an NPP accident. The wind data used in the study was collected from a meteorological tower located at the NPP site, and measurements were taken at 1-hour intervals for each operation over a period of ten years. The collected data underwent preprocessing, followed by the development of Python code to render the wind rose diagrams in an interpretable format. The future direction of this study will be focused on enhancing this program by integrating geographical mapping capabilities. With these advancements, it will become feasible to superimpose shelter positions on a map in accordance with prevailing wind directions. These improvements will contribute to the development of additional protective measures for residents and the proposal of alternative shelter options in response to potential radioactive material releases.

The demand for transportation is increasing due to the continuous generation of radioactive wastes. Especially, considering the geographical characteristics of Korea and the location characteristics of nuclear facilities, the demand for maritime transportation is expected to increase. If a sinking accident happens during maritime transportation, radioactive materials can be released into the ocean from radioactive waste transportation containers. Radioactive materials can spread through the ocean currents and have radiological effects on humans. The effect on humans is proportional to the concentration of radioactive materials in the ocean compartment. In order to calculate the concentration of radioactive materials that constantly flow along the ocean current, it is necessary to divide the wide ocean into appropriate compartments and express the transfer processes of radioactive materials between the compartments. Accordingly, this study analyzed various ocean transfer evaluation methodologies of overseas maritime transportation risk codes. MARINRAD, POSEIDON, and LAMER codes were selected to analyze the maritime transfer evaluation methodology. MARINRAD divided the ocean into two types of compartments that water and sediment compartments. And it was assumed that radionuclides are transfered from water to water or from water to sediment. Advection, diffusion, and sedimentation were established as transfer process for radionuclides between compartments. MARINRAD use transfer parameters to evaluate transer processes by advection, diffusion, and sedimentation. Transfer parameters were affected by flow rate, sedimentation rate, sediment porosity, and etc. POSEIDON also divided the ocean into two types that water and sediment compartment, each compartments was detaily divided into three vertical sub-compartment. Advection, diffusion, resuspension, sedimentation, and bioturbation were established as transport processes for radionuclides between compartments. POSEIDON also used transfer parameters for evaluating advection, diffusion, resuspension, sedimentation, and bioturbation. Transfer parameters were affected by suspended sediment rates, sedimentation rates, vertical diffusion coefficients, bioturbation factors, porosity, and etc. LAMER only considered the water compartment. It divided the water compartment into vertical detailed compartments. Diffusion, advection and sedimentation were established as the nuclide transfer processes between the compartments. To evaluated the transfer processes of nuclides for diffusion and advection, LAMER calculated the probability with generating random position vectors for radionuclides’ locations rather than deterministic methods such as MARINRAD’s transfer parameters or POSEIDON’s transfer rates to evaluate transfer processes. The results of this study can be used as a basis for developing radioactive materials’ ocean transfer evaluation model.

This study presents distribution of naturally occurring radioactive materials in groundwater in Jeju island. Radon (222Rn) and potassium (40K) concentrations were performed by using Liquid Scintillation Counter and Ion Chromatograph respectively. In addition, the activities of uranium and thorium nuclides were analyzed by Inductively Coupled Plasma Mass Spectroscopy. Groundwater samples were collected from 9 sites of water intake facilities for wide area supply in Jeju island from September 2022 to September 2023. The 40K concentrations of groundwater ranged between 0.050 and 0.400 Bq·L-1. The radon concentrations in groundwater were in the range of 0 to 60 Bq L-1, and there was no groundwater exceeding the range of 148 Bq L-1 proposed by the US EPA. The distribution of uranium and thorium in groundwater varied from 0 to 500 ng L-1 and 0 to 2.4 ng L-1, respectively. The concentrations of uranium did not exceed 30 μg L-1, thresholds indicated by the US EPA. By analyzing the concentrations of 40K, 222Rn, 238U and 232Th, the annual effective dose of residents can be assessed. The evaluated residents’ effective dose from natural radionuclides due to intake of drinking water is less than the recommended value of 100 μSv y-1. Consequently, this study indicates that the cancer risks of the residents in Jeju island from naturally occurring radioactive materials ingested with water is insignificant.

Various types of radioactive liquid and solid wastes are generated during the operation and decommissioning of nuclear power plants. To remove radionuclides Co-60, Cs-137 etc. from a liquid waste, the ion-exchange process based on organic resins has been commonly used for the operation of nuclear facilities. Due to the considerations for the final disposal of process endproduct, other treatment methods such as adsorption, precipitation using some inorganic materials have been suggested to prepare for large amounts of waste during decommissioning. This study evaluated sintering characteristics for radioactive precipitates generated during the liquid waste treatment process. The volume reduction efficiency and compressive strength of sintered pellets were the major parameters for the evaluation. Major components of a simulated precipitate were some coagulated (oxy) hydroxides containing light elements, such as Si, Al, Mg, Ca, and zeolite particles. Green pellets compressed to around 100 MPa were heated at a range of 750~850°C to synthesize sintered pellets. It was observed that the volume reduction percentages were higher than 50% in the appropriate sintering conditions. The volume reduction was caused by the reduction of void space between particles, which is an evidence of partial glassification and ceramization of the precipitates. This result can also be attributed to conversion reactions of zeolite particles into other minerals. The compressive strength ranged from 6 to 19 MPa. These results also showed a significant correlation with the volume reduction of sintered body. Although our lab-scale experiments showed many benefits of sintering for the precipitates, optimized conditions are needed for large-scale practical applications. Evaluation of sintering characteristics as a function of pellet size and further testing will be conducted in the future.

In the dismantling of nuclear power plants, various forms of radioactive gaseous waste are generated when cutting concrete and metal structures. Large amounts of radioactive dust and aerosols generated during the cutting process of each structure can cause radiation exposure to the environment around the workplace and to the radiation exposure in the body of workers. When cutting structures, water is sprayed to reduce the generation of aerosols, so early saturation of the filter is expected due to radioactive aerosols and fine particles containing a large amount of moisture. A mobile air purification device is being developed to a fast and efficient air purifier that can be used for a long time operation to protect workers from radiation exposure in high radiation areas and to minimize the amount of secondary waste generated. In this paper, the direction for a new concept of unit technology that can achieve the development purpose is described.