Warm compaction powder metallurgy was used to produce a Ti3SiC2 particulate reinforced Cu matrix composite. Fabrication parameters and warm compaction behaviors of Cu powder were studied. Based on the optimized fabrication parameters a Cu-based electrical contact material was prepared. Results showed that in expend of some electrical conductivity, addition of Ti3SiC2 particulate increased the hardness, wear resistivity and anti-friction ability of the sintered Cu-base material.

Homogeneous microstructures of the PM compacts are difficult to attain when mixed elemental powders are used. This study examined the microstructures of pressed-and-sintered and MIM products that contain Ni and Mo.Ni-rich areas, which were lean in carbon and were soft and were found easily in regular specimens. Gaps or cracks near the Ni-rich or Mo-rich areas were also frequently observed. This problem worsened when Ni and Mo particles were large and were irregular in shape. By using ball milling treatment and ferroalloy powders, the microstructure homogeneity and mechanical properties were improved. The addition of 0.5wt%Cr further improved the distribution of Ni because Cr reduced the repulsion effect between nickel and carbon. With the elimination of Ni-rich areas, more bainites and martensites were formed and mechanical properties were significantly improved.

The kneading process and formulations of feedstock obviously affect the quality of MIM products. In the present work, the rheological behaviour of the composite MIM feedstock, metal matrix (Cu) with few additions of ceramic powders (Al2O3), was measured by a self-designed/manufactured simple capillary rheometer. Experimental results show that the distribution between powders and binder is more uniformly when blending time increased. Though high powder loading will increase the feedstock viscosity, the fluidity reveals relatively stable through the load curves of extrusion. Besides, the temperature-dependence of viscosity of the feedstock approximately follows an Arrehnius equation. Basing on Taguchi’s method, the kneading optimization conditions and the rheological model of the feedstock were established, respectively.

Powder injection molding (PIM) is a suitable technology for the fabrication of complex shape titanium and its alloys, and has a great potential in many applications. This paper dealt with the injection molding of hydride dehydrogenization (HDH) titanium powder, spheroidized HDH titanium powder and gas atomized titanium powder. Rheological and thermalgravimetric behaviors were compared between the feedstocks of the three powders, and a tentative application of Ti PIM to eye frame temple and bridge was briefed.

A QM-ISP-4 Planetary Mill was employed to activate mechanically the mixtures of anatase and corundum at room temperature for different times. The milled powder mixtures were then sintered at for 1 h. The XRD results showed that the milled powder mixtures were completely transformed into after sintering, except the mixtures milled for 5 and 10 hours. The SEM observations showed the typical morphology of rod-like vary in the range: widths from 0.6 to , and lengths from 3.0 to . The rod-like formation was attributed to the positive effects caused by the mechanical activation.

In recent years, micro powder injection molding is being explored as an economical fabrication method for microcomponents in microsystems technology (MST). Technical and economic comparison was performed for processes. Molding experiment and simulation during the filling process were performed to evaluate several different geometries and processing conditions. The influence of material parameters and process conditions on mold filling were examined as a function of features size using microchannels as an example. It was found that the heat conductivity and viscosity of feedstock, geometry and mold temperature were the most critical parameters for complete filling of micro features.

Capping mechanisms during the compaction of pharmaceutical powders were explored. Both experimental and numerical investigations were performed. For the experimental study, an X-ray Computed Microtomography system has also used to examine the internal failure patterns of the tablets produced using a compaction simulator. Finite element (FE) methods have also been used to analyse the powder compaction. The experimental and numerical studies have shown that the shear bands developed at the early stage of unloading appear to be responsible for the occurrence of capping. It has also been found that the capping patterns depend on the compact shape.

본 연구에서는 고준위 방사성폐기물 심지층 처분시설의 규모 및 layout설정에 필요한 요소인 처분터널 및 처분공 간격에 대한 분석을 수행하였다. 이를 위하여, 기준 처분개념과 공학적 방벽 개념을 바탕으로 다양한 조건의 처분터널 및 처분공 단면을 설정하고, 단층 배치 및 복층 배치 개념 에 따른 처분동굴의 구조적, 열적 안정성을 분석하였다. 분석 결과를 바탕으로 설계에 있어서 주요한 고려인자 중의 하나인 굴착량을 감소시킬 수 있는 처분동굴 및 처분공 간격을 제안하였다. 본 연구의 결과는 심지층 처분시설 설계시 활용될 것이며, 향후, 부지에 대한 불확실성을 줄이기 위하여 정확한 부지특성 자료를 통한 상세한 분석이 필요하다.

This paper investigated the optimum design of truss structures based on Genetic Algorithms (GA's). With GA's characteristic of running side by side, the overall optimization and feasible operation, the optimum design model of truss structures was established. Elite models were used to assure that the best units of the previous generation had access to the evolution of current generation. Using of non-uniformity mutation brought the obvious mutation at earlier stage and stable mutation in the later stage; this benefited the convergence of units to the best result. In addition, to avoid GA's drawback of converging to local optimization easily, by the limit value of each variable was changed respectively and the genetic operation was performed two times, so the program could work more efficiently and obtained more precise results. Finally, by simulating evolution process of nature biology of a kind self-organize, self-organize, artificial intelligence, this paper established continuous structural optimization model for ten bars cantilever truss, and obtained satisfactory result of optimum design. This paper further explained that structural optimization is practicable with GA's, and provided the theoretic basis for the GA's optimum design of structural engineering.

Using 13.7 m telescope of Qinghai station of NAO, PMO at Delin Ha, 43 IRAS sources were mapped with 13CO J=1-0 C18O J=1-0 and CO J=1-0. Each source has one or more cores. The distances of these cores range from 1 pc to several pc, and the masses from 102M⊙ to 105M⊙. High velocity outflows were detected. The mass, momentum and energy of these massive cores are larger than those of the low mass ones. With radio, IRAS, MSX data, stellar source distribution were investigated, and sourceless cores that deviate from infrared sources were identified. They are potential high mass star formation sites.

Somatic cell nuclear transfer in cattle has limited efficiency in terms of production of live offspring due to high incidence of fetal failure after embryo transfer to recipients. Such low efficiency of cloning could possibly arise from abnormal and poorly developed placenta. In the present study the placental proteome in late pregnancy established from in vitro fertilization (IVF) and nuclear transfer (NT) was analysed. Proteome alternation was tested using two-dimensional polyacrylamide gel electrophoresis (2-DE) and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI- TOF). Comparing placenta from NT embryos to those from IVF counterparts, significant changes in expression level were found in 18 proteins. Of these proteins 12 were not expressed in NT placenta but expressed in IVF counterpart, whereas the expression of the other 6 proteins was limited only in NT placenta. Among these proteins, cytokeratin 8 and vimentin are considered to be involved in regulation of post-implantation development. In particular, cytokeratin 8 and vimentin may be used as makers for placental development during pregnancy because their expression levels changed considerably in NT placental tissue compared with its IVF counterpart. Data from 2-DE suggest that protein expression was disorientated in late pregnancy from NT, but this distortion was eliminated with progression of pregnancy. These findings demonstrate abnormal placental development during late pregnancy from NT and suggest that alterations of specific placental protein expression may be involved in abnormal function of placenta.