Level measurement of liquid radwaste is essential for inventory management of treatment system. Among various methods, level measurement based on differential pressure has many advantages. First, it is possible to measure the liquid level of the system regardless of liquid type. Second, as the instrument doesn’t need to be installed near the tank, there is no need to contact the tank when managing it. Therefore, workers’ radiation dose from the system can be decreased. Finally, although it depends on the accuracy, the price of the instrument is relatively low. With these advantages, in general, liquid radwaste level in a tank is measured using differential pressure in the treatment system. Not only the advantages described above, there are some disadvantages. As the liquid in the system is waste, it is not pure but has some suspended materials. These materials can be accumulated in tanks and pipes where the liquids move to come into direct contact with pneumatic pipes that are essential in differential pressure instruments. As a result, in case of a treatment using heat source, the accumulated materials may become sludge causing interference in pneumatic pipes. And this can change the pressure which also affects the level measured. In conclusion, in case of liquid storage tanks in which the situation cannot be checked, the proficiency of an operator becomes important.

The timescale of safety assessment for a geological disposal system is considered up to hundreds of thousands of years when the radionuclides in spent nuclear fuel decay to levels comparable to natural radioactivity. During this long period, a variety of climate changes are expected to occur, including variations in temperature and precipitation as well as long-term sea level changes and glacial cycles. These climate changes can either directly affect water balance components or indirectly affect water balance by altering terrain and vegetation that have an impact on water balance. Water balance is a significant element of safety assessment, because it affects the radionuclide transport via groundwater flow, which in turn affects the radiological risk to humans and other biotas. Therefore, it is important to understand the hydrologic response to climate changes for proving the long-term safety of the disposal system. To this end, this study performed hydrological simulations using the SWAT (Soil and Water Assessment Tool) for several climate change scenarios. SWAT is the watershed-scale hydrological model developed by the USDA-ARS (United States Department of Agriculture - Agricultural Research Service) and has been widely used to quantify the water balance in a watershed. It calculates the hydrologic cycle based on the water balance equation with different physical processes for water balance components such as evapotranspiration, surface runoff, and groundwater recharge. This study assumed several climate change scenarios (e.g., variations in temperature and precipitation, sea level change, and formation of permafrost) and analyzed how the components of the water balance would respond under different scenarios and which scenarios would have the greatest impact on the water balance. These findings can provide valuable insights for future long-term safety assessments on the Korean Peninsula and can also be used as input data for the biosphere module of APro (Adaptive process-based total system performance assessment framework).

With the increasing demand for a repository to safely dispose of high-level radioactive waste (HLW), it is imperative to conduct a safety assessment for HLW disposal facilities for ensuring the permanent isolation of radionuclides. For this purpose, the Korea Atomic Energy Research Institute (KAERI) is currently developing the Adaptive Process-based total system performance assessment framework for a geological disposal system (APro). A far-field module, which specifically focuses on fluid flow and radionuclide transport in the host rock, is one of several modules comprising APro. In Korea, crystalline rock is considered the host rock for deep geological disposal facilities due to its high thermal conductivity and extremely low permeability. However, the presence of complex fracture system in crystalline rock poses a significant challenge for managing fluid flow and nuclide transport. To address this challenge, KAERI is participating in DECOVALEX-2023 Task F1, which seeks to compare and verify modeling results using various levels of performance assessment models developed by each country for reference disposal systems. Through the benchmark problems suggested by DECOVALEX-2023 Task F1, KAERI adopts the Discrete Fracture-Matrix (DFM) as the primary fracture modeling approach. In this study, the transport processes of reactive tracers in fractured rock, modeled with DFM, are simulated. Specifically, three different tracers (conservative, decaying, adsorbing) are introduced through the fracture under identical injecting conditions. Thereafter, the breakthrough curves of each tracer are compared to observe the impact of reactive tracers on nuclide transport. The results of this study will contribute to a better understanding of nuclide behavior in subsurface fractured rock under various conditions.

The Korean Nuclear Safety and Security Commission has established a general guideline for the disposal of high-level waste, which requires that radiological effects from a disposal facility should not exceed the regulatory safety indicator, a radiological risk. The post-closure safety assessment of the disposal facility aims to evaluate the radiological dose against a representative person, taking into account nuclide transport and exposure pathways and their corresponding probabilities. The biosphere is a critical component of radiation protection in a disposal system, and the biosphere model is concerned with nuclide transport through the surface medium and the doses to human beings due to the contaminated surface environment. In past studies by the Korea Atomic Energy Research Institute (KAERI), the biosphere model was constructed using a representative illustration of surface topographies and groundwater conditions, assuming that the representative surface environment would not change in the future. Each topography was conceptualized as a single compartment, and distributed surface contamination over the geometrical domain was abstracted into 0D. As a result, the existing biosphere model had limitations, such as a lack of quantitative descriptions of various transport and exposure pathways, and an inability to consider the evolution of the surface environment over time. These limitations hinder the accurate evaluation of radiological dose in the safety assessment. To overcome these limitations, recent developments in biosphere modeling have incorporated the nuclide transport process over a 2D or 3D domain, integrating the time-dependent evolution of the surface environment. In this study, we reviewed the methodology for biosphere modeling to assess the radiological dose given by distributed surface contamination over a 2D domain. Based on this review, we discussed the model requirements for a numerical module for biosphere dose assessment that will be implemented in the APro platform, a performance assessment tool being developed by the KAERI. Finally, we proposed a conceptual model for the numerical module of dose assessment.

In Korea, the construction of dry storage facilities for spent nuclear fuel is being promoted through the 2nd basic plan for high-level radioactive waste management. When operating dry storage facilities, exposure dose assessment for workers should be performed, and for this, exposure scenarios based on work procedures should be derived prior. However, the dry storage method has not yet been sufficiently established in Korea, so the work procedure has not been established. Therefore, research is needed to apply it domestically based on the analysis of spent nuclear fuel management methods in major overseas leading countries. In this study, the procedure for receiving and storing spent nuclear fuel in a concrete overpack-based storage facility was analyzed. Among the various spent nuclear fuel management systems, the metal overpack-based HI-STAR 100 system and the concrete overpackbased HI-STORM 100 system are quite common methods in the United States. Therefore, in this study, work procedures were analyzed based on each final safety analysis report. First, the HI-STAR 100 overpack enters the facility and is placed in the transfer area. Remove the impact limiter of the overpack and install the alignment device on the top of the overpack. Place the HI-TRAC, an on-site transfer device, on top of the alignment unit and remove the lids of the two devices to insert the canister into the HI-TRAC. When the canister transfer is complete, reseat the lid to seal it, and disconnect the HI-TRAC from the HI-STAR 100. Raise the canister-loaded HI-TRAC over the alignment device on the top of the HI-STORM 100 overpack and remove the lids of the two devices that are in contact. Insert the canister into the HI-STORM 100 and reseat the lid. The HI-STORM 100 loaded with spent nuclear fuel is transferred to the designated storage area. In this study, the procedure for receiving and storing spent nuclear fuel in a concrete overpack-based storage facility was analyzed. The main procedure was the transfer of canisters between overpacks, and it was confirmed that HI-TRAC was used in the work procedure. The results of this study can be used as basic data for evaluating the exposure dose of operating workers for the construction of dry storage facilities in Korea.

Molten Salt Reactor (MSR) is one of Generation-IV nuclear reactors that uses molten salts as a fuel and coolant in liquid forms at high temperatures. The advantages of MSR, such as safety, economic feasibility, and scalability, are attributed from the fact that the molten salt fuel in a liquid state is chemically stable and has excellent thermo-physical properties. MSR combines the fuel and coolant by dissolving the actinides (U, Th, TRU, etc.) in the molten salt coolant, eliminating the possibility of a core meltdown accident due to loss of coolant (LOCA). Even if the molten salt fuel leaks, the radioactive fission products dissolved in the molten salt will solidify with the fuel salt at room temperature, preventing potential leakage to the outside. MSR was first demonstrated at ORNL starting with the Aircraft Reactor Experiment (ARE) in 1954 and was extended to the 7.4 MWth MSRE developed in 1964 and operated for 5 years. Recently, various start-ups, including TerraPower, Terrestrial Energy, Moltex Energy, and Seaborg, have been conducting research and development on various types of MSR, particularly focusing on its inherent safety and simplicity. While in the past, fluoride-based molten salt fuels were used for thermal neutron reactors, recently, a chlorine-based molten salt fuel with a relatively high solubility for actinides and advantageous for the transmutation of spent nuclear fuel and online reprocessing has been developing for fast neutron spectrum MSRs. This paper describes the development status of the process and equipment for producing highpurity UCl3, a fuel material for the chlorine-based molten salt fuel, and the development status of the gas fission product capturing technologies to remove the gaseous fission products generated during MSR operation. In addition, the results of the corrosion property evaluation of structural materials using a natural circulation molten salt loop will also be included.

Background: Individuals with scapular winging have a weak serratus anterior (SA) muscle, and to compensate, the pectoralis major (PM) and upper trapezius (UT) muscles excessively activate, which can cause upper extremity dysfunction. This study aimed to compare the effects of isometric horizontal abduction (IHA) on SA, PM, and UT muscle activity, as well as the SA/PM and SA/UT muscle activity ratios during knee push-up plus (KPP) at 90° and 120° of shoulder flexion. Objects: This study aimed to compare the effects of IHA on SA, PM, and UT muscle activity, as well as the SA/PM and SA/UT muscle activity ratios during KPP at 90° and 120° of shoulder flexion. Methods: This study, conducted at a university research laboratory, included 20 individuals with scapular winging. Participants performed KPP with and without IHA at 90° (KPP90) and 120° (KPP120) of shoulder flexion. SA, PM, and UT muscle activity were measured using surface electromyography. Results: PM activity in KPP90 with IHA was significantly lower than KPP90 and in KPP120 was significantly lower than KPP90. UT activity was significantly greater with IHA than without IHA and at 120° than 90° of shoulder flexion. SA/PM muscle activity ratio was significantly higher in KPP90 with IHA than without IHA and in KPP120 than in KPP90. SA/UT muscle activity ratio was significantly lower with IHA than without IHA. Conclusion: KPP90 with IHA and KPP120 are effective exercises to reduce PM activity and increase SA/PM muscle activity ratio. However, applying IHA in KPP90 also reduces SA/UT muscle activity ratio, implying that it would be preferable to apply KPP120 in individuals overusing their UT muscles.