현재 인간이 일반적으로 이용하는 의료용 단백질은 대개 동물세포 배양기술에 의하여 생산되고 있다. 그러나 제한된 특정 시설에서 생산되기 때문에 생산 단가가 높아서 전세계의 수요가 증가함에도 불구하고 일반화하는 데는 한계가 있는 실정이다. 이러한 문제를 극복하기 위하여 오래전부터 식물시스템을 이용하여 의료용 단백질을 생산하는 연구가 관심을 끌고 있다. 즉 쉽게 규모화할 수 있고 생산비용 효과도 경제적이고 동물세포보다 더 안전하게 의료용 단백질 생산할 수 있는 수단이 될 수 있기 때문이다. 이를 위하여 식물에 안정적으로 유전자를 핵 게놈과 엽록체 게놈에 형질전환 시키는 기술과 바이러스 운반체를 이용하여 일시적 발현을 유도함으로 의료용 단백질을 생산하는 기술이 개발되고 있다. 최근 해체 바이러스 기반의 운반체 개발은 재조합 단백질을 빠르고 일시적 발현으로 대량생산을 가능하게 하고 있다. 따라서 이 바이러스 발현시스템이 적절한 식물기반의 대량생산을 위한 플렛폼을 제공하고 있다. 따라서 본 총설은 식물로부터 의료용 단백질을 생산하는데 있어서 식물 바이러스발현 시스템 개발 및 이용에 대하여 기술하였다.

This study evaluated the enhancement of microstructural and mechanical properties of a cross rolled Ni-10Cr alloy, comparing with conventionally rolled material. Cold rolling was carried out to 90% thickness reduction and the specimens were subsequently annealed at 700˚C for 30 min to obtain a fully recrystallized microstructure. Cross roll rolling was carried out at a tilted roll mill condition of 5˚ from the transverse direction in the RD-TD plane. In order to observe the deformed microstructures of the cold rolled materials, transmission electron microscopy was employed. For annealed materials after rolling, in order to investigate the grain boundary characteristic distributions, an electron back-scattering diffraction technique was applied. Application of cold rolling to the Ni-10Cr alloy contributed to notable grain refinement, and consequently the average grain size was refined from 135 μm in the initial material to 9.4 and 4.2 μm in conventionally rolled and cross rolled materials, respectively, thus showing more significantly refined grains in the cross rolled material. This refined grain size led to enhanced mechanical properties such as yield and tensile strengths, with slightly higher values in the cross rolled material. Furthermore, the<111>//ND texture in the CRR material was better developed compared to that of the CR material, which contributed to enhanced mechanical properties and formability.

We carried out this study to evaluate the grain refining in and the mechanical properties of alloys that undergo severe plastic deformation (SPD). Conventional rolling (CR) and cross-roll rolling (CRR) as SPD methods were used with Ni-20Cr alloy as the experimental material. The materials were cold rolled to a thickness reduction of 90% and subsequently annealed at 700˚C for 30 min to obtain a fully recrystallized microstructure. For the annealed materials after the cold rolling, electron back-scattered diffraction (EBSD) analysis was carried out to investigate the grain boundary characteristic distributions (GBCDs). The CRR process was more effective when used to develop the grain refinement relative to the CR process; as a result, the grain size was refined from 70μm in the initial material to 4.2μm (CR) and 2.4μm (CRR). These grain refinements have a direct effect on improving the mechanical properties; in this case, the microhardness, yield and tensile strength showed significant increases compared to the initial material. In particular, the CRR-processed material showed more effective values relative to the CR-processed materials. The different texture distributions in the CR (001//ND) and CRR (111//ND) were likely the cause of the increase in the mechanical properties. These findings suggest that CRR can result in materials with a smaller grain size, improved texture development and improved mechanical properties after recrystallization by a subsequent annealing process.

The present study was carried out to evaluate the microstructural and mechanical properties of cross-roll rolled pure copper sheets, and the results were compared with those obtained for conventionally rolled sheets. For this work, pure copper (99.99 mass%) sheets with thickness of 5 mm were prepared as the starting material. The sheets were cold rolled to 90% thickness reduction and subsequently annealed at 400˚C for 30 min. Also, to analyze the grain boundary character distributions (GBCDs) on the materials, the electron back-scattered diffraction (EBSD) technique was introduced. The resulting cold-rolled and annealed sheets had considerably finer grains than the initial sheets with an average size of 100 μM. In particular, the average grain size became smaller by cross-roll rolling (6.5 μM) than by conventional rolling (9.8 μM). These grain refinements directly led to enhanced mechanical properties such as Vickers micro-hardness and tensile strength, and thus the values showed greater increases upon cross-roll rolling process than after conventional rolling. Furthermore, the texture development of<112>//ND in the cross-roll rolling processed material provided greater enhancement of mechanical properties relative to the case of the conventional rolling processed material. In the present study, we systematically discuss the enhancement of mechanical properties in terms of grain refinement and texture distribution developed by the different rolling processes.

Chloride-based fluxes such as NaCl-KCl are used in the refining of Al melt. The vapor pressure of the chloride is one of the fundamental pieces of information required for such processes, and is generally high at elevated temperatures. In order to measure the vapor pressure for chlorides, the apparatus for the transpiration method was assembled in the present study. The vapor pressure of ZnCl2 and FeCl2, which is related with the process of aluminum refining and the recovery of useful elements from iron and steel industry by-products, was also measured. In the measurement of vapor pressure by the transpiration method, the powder of ZnCl2 or FeCl2 in a alumina boat was loaded in the uniform zone of the furnace with a stream of Ar. The weight loss of ZnCl2 and FeCl2 after holding was measured by changing the flow rate of Ar gas (10 sccm -230 sccm), and the partial pressures of ZnCl2 and FeCl2 were calculated. The partial pressures within a certain range were found to be independent of the flow rate of Ar at different temperatures. The vapor pressures were measured in the temperature range of 758-901K for ZnCl2 and 963-983K for FeCl2. The measured results agreed well with those in the literature.

Background : The human patch test is a method used to evaluate potential skin irritation after contact with a cosmetic materials. Pectin lyase-modified red ginseng extract (GS-E3D) is a newly developed ginsenoside Rd-enriched ginseng extract. This study was designed to investigate the skin safety of GS-E3D in human patch test. Methods and Results : Thirty two female volunteers were tested with GS-E3D. GS-E3D (20 ㎕) was applied to occlusive patch test devices and was then applied onto the back of subject with normal skin for 24 hours. Cutaneous irritation responses were evaluated and graded according to criterion of International Contact Dermatitis Research Group (ICDRG) at 30 min, 24 hours, and 48 hours after removing of GS-E3D patch. The average age of subjects was 47.3 ± 9.3 years. Skin reactivity calculated from irritation score in GS-E3D treated group was 0.51 and skin irritation score of no application group was 0, respectively. Skin irritancy was no response in both GS-E3D treated group and no application group. From above data, GS-E3D was identified as a non-irritant according to ICDRG guideline that skin irritation score of ‘0.00 - 0.75’ is a non-irritant. Conclusion : These results indicate that GS-E3D can be useful as a safe cometic ingredient.

Background : Pectin lyase-modified red ginseng extract (GS-E3D) is a newly developed ginsenoside Rd-enriched ginseng extract. This study was designed to investigate the acute oral and dermal toxicity of GS-E3D in rat. Methods and Results : The acute oral toxic effects of GS-E3D in female SD rats were examined at dosages of 300 ㎎/㎏ and 2,000 ㎎/㎏. In acute dermal toxicity study, 500, 1,000 and 2,000 ㎎/㎏ of GS-E3D were applied onto the shaved skin of male and female SD rats. The weights of rats were recorded at 0, 1, 3, 7, and 14 days and clinical observation were checked once a day for a period of 14 days. All rats were scarified on 14th day and complete gross examination was conducted to detect any gross change of organs after necropsy. GS-E3D did not produce orally or dermally treatment-related clinical signs of toxicity or mortality in all rats during the 14-day observation period. The oral and dermal LD50 values of GS-E3D were over 2,000 ㎎/㎏ in rat. The oral and dermal administration of GS-E3D revealed no significant change in body weight and gross pathology examination compared to control group. Conclusion : These results indicate that GS-E3D can be used as a food and cosmetic materials without critically adverse effect.