자외선차단 화장품은 기능성 화장품 중의 하나로서, 유·무기 자외선차단물질이 함유되어 있다. 무기계 자외선차단제는 주로 산화아연, 이산화티탄 등이 있다. 무기계 자외선차단제는 입자의 지름이 60 ~ 100 nm로 자외선 A, B의 차단능이 좋은 것으로 알려져 있다. 또한 자외선을 포함한 태양광선에 대해 비활성이 크고 안전성이 우수하다. 그리고 유기계 자외선차단제처럼 피부에 흡수 또는 축적되지 않으므로 피부 자극이나 알레르기를 유발하지 않는다. 본 연구에서는 판상 무기안료인 마이카, 자외선차단 효과를 갖는 이산화티탄 나노입자, 소수성 실리카를 각각 계면활성제로 표면처리 하였고, 각 물질의 전하 차이에 따른 비화학적인 상호 인력 작용에 의해 마이카에 이산화티탄 나노입자, 실리카를 물리적으로 흡착시켰다. 이후, 소수성 표면처리제인 실란을 표면처리 하여 소수성을 갖는 자외선 차단 판상 마이카 복합체를 제조하였다. 자외선 차단 판상 마이카 복합체는 일반적인 나노입자 이산화티탄의 응집성을 개선하고 균일한 분산에 따른 자외선차단 효과가 증대되었으며, 소수성으로 표면처리를 하여 화장품 제형에서의 분산안정성을 크게 개선할 수 있었다. 안료의 표면전하는 제타전위로 평가하였으며, 제조된 자외선차단 마이카 복합체의 특성 평가는 FE-SEM, XRD, FT-IR, UV-VIS 등으로 확인하였다.

A nationwide survey of 8 N-nitrosamines in finished water samples from drinking water treatment plants (DWTPs) in Korea was conducted. The samples were pre-treated by solid-phase extraction (SPE) and analyzed using a gas chromatography coupled with tandem mass spectrometry (GC-MS/MS). According to the study results, four N-nitrosamines (NDMA, NDEA, NMOR, NDBA) were detected for three consecutive years, NMEA and NPYR were only found in samples collected in 2013. Two of these N-nitrosamines, N-nitrosodimethylamine (NDMA) and N-nitrosodiethylamine (NDEA), have received attention and were the most commonly detected. The concentration of NDMA and NDEA in this study ranged from 0.002 μg/L to 0.013 μg/L and in 0.001 μg/L to 0.008 μg/L, respectively. In comparison to studies performed in EPA(UCMR2), the concentrations of NDMA (from 0.002 μg/L to 0.630 μg/L) and NDEA (from 0.005 μg/L to 0.100 μg/L) observed in the this study were low.

The chemical structures of perfluorinated compounds(PFCs) have unique properties such as thermal and chemical stability that make them useful components in a wide variety of consumer and industrial products. Two of these PFCs, perfluorooctane sulfonate(PFOS) and perfluorooctanoic acid(PFOA), have received attention and were the most commonly detected. In this study it was analyzed the concentrations of 8 PFCs in samples were collected from drinking water treatment plants for 5 years(2012-2016). PFOS and PFOA were also high concentration and frequency. The mean concentrations of PFOA and PFOS were detected 0.0026-0.0069 μg/L and 0.0009-0.0024 μg/L in samples from drinking water treatment plants. These were relatively lower or similar compared to PFOS concentrations in Osaka(Japan). In general, these levels are below health-based values set by international authoritative bodies for drinking water. These results will be serve as the first monitoring data for PFCs in drinking water and be useful for characterizing the concentration distribution and management of PFCs in future studies.

1996년에 창설된 타이페이 비엔날레(TB)의 기획 메커니즘은 타이완 출신 큐레이터들의 공동 기획 체제(1996)로부터 일본 출신의 단일 큐레이터 체제(1998), 그리고 해외 큐레이터와 국내 큐레이터가 협업하는 이원 큐레이터 체제(2000-2010)를 거쳐서 다시 단일 큐레이터 체제(2012-2016)으로 회귀하기까지 다양한 과정을 겪었다. 특히 최근 단계에서는 서구 출신의 큐레이터들이 주도권을 장악해 왔다. 본 논문에서는 타이페이 비엔날레의 창립 당시 목표와 후대의 전개 양상 사이의 괴리 현상을 분석한다. 연구자는 이 행사가 타이완의 복합적인 지역 담론과 쟁점들을 제대로 반영하지 못하고 단순히 동시대 국제 비엔날레의 추세를 수용하는데 머 물러 왔으며, 그 배경에 타이페이 비엔날레의 기획 메커니즘 뒤에 작용하고 있는 ‘자기 식민 지화’의 경향이 존재한다고 주장한다.

남한산 큰자색호랑꽃무지는 그 동안 일본에 분포하는 Osmoderma opicum으로 동정되어 왔으며, 국내에서는 그 희귀성에 의해 멸종위기종으 로 다루어지고 있지만, 남한 개체군에 대한 면밀한 종의 실체에 대한 구명은 없었다. 이에 대해, 남한산 큰자색호랑꽃무지와 유라시안 근연종에 대 해 형태 및 COI유전자 염기서열을 비교를 실시하였다. 결과적으로, 남한산 개체군은 형태적으로 극동러시아에 분포하는 O. caeleste와 동일하였다. 따라서, 남한산 큰자색호랑꽃무지는 O. caeleste임을 제안한다.

In order to prevent secondary pollution of tap water, corrosion characteristics are investigated, and corrosion index are calculated using LI and LR to manage corrosiveness. As targeted water treatment plants from 2014 (July, once) to 2015 (July and October, 2 times), 70 plants are selected by making a division for each area and water system. (treated water samples, n=240, raw water samples, n=72). In result of pH analysis, treated water was lower than raw water to 7.12, and 7.29, respectively. LI were investigated in the order of Seomjin river, Nakdong river, Han river, Geum river, to -2.08, -1.24, -1.11, -1.10 (at raw water), and -2.18, -1.59, -1.51, -1.35 (at treated water), respectively. In case of water quality goal value (LI = -1) in Japan as control of corrosiveness, management object was investigated about 83.3%.

This study investigates on the tuning stainless steel(STS630) to understand for groove cutting characteristics. For this purpose, we observed the cutting force according to feed rate and cutting speed variation and performed the computational analysis due to groove cutting depth. In groove cutting of stainless steel, there were principal force, feed force and radial force by arranging the highest cutting force in order. In case of wall thicknesses of 0.3mm and 0.5mm at groove cutting, principal force increases according to the increase of feed rate but it is not related to cutting speed. We found the unstable region of cutting force that is caused to the friction resistance of cutting tool and elastic deformation of groove wall. In computational analysis, we confirmed that the more feed rate increases, the more strain increases around the tooth root.

In this study, we conducted an interrupted cutting SM20C with lathe and uncoated carbite tool, determined the relationship between Cutting Forces(principal, radial, feed force) by correlation analysis, and predicted the optimum cutting conditions by multiple regression analysis. The result were as follow. : From the correlation analysis, the increase of cutting speed and depth of cut reduces the principal force and radial force. the increase of cutting speed, depth of cut and feed rate will increase the feed force. From multi-regression analysis, we extracted regression equation and the coefficient of determination (R2) was 0.638, 0.692, 0.536 at principal, radial and feed force . It means that the regression equation is not high accuracy. However, it is predictable that the tendency of the forces action the interrupted cutting.

공조시스템의 소음 예측은 주로 NEBB에서 제안한 경험적인 방법에 의해 수행된다. 그러나, NEBB에서 제안한 방법은 선박에만 있는 대형 덕트의 요소를 반영하지 못하므로 선박에 적용하는데 한계가 있다. 본 논문에서는 선박용 대형 덕트의 소음 예측을 위한 전산해석방법을 연구하였다. 경계요소법을 사용하여 대형 덕트의 단위 길이당 소음 감소량에 대한 추정식을 개발하였고, 경계요소법과 전산유체역학을 사용하여 보강재가 설치된 대형 덕트에서의 유동기인소음을 예측하였다. 유입 유속이 10m/s, 보강재의 종류가 200플랫 바인 경우 100 dB 이상의 큰 소음이 발생하는 것을 알 수 있었다. 또한, 경계요소법과 유한요소법을 사용하여 덕트 투과 소음을 예측하였다. 덕트 내부와 외부의 음압 값 차이는 대략 10~15 dB정도 인 것을 알 수 있었다. 이를 통해 조선소에서는 대형 덕트를 포함한 선박 HVAC 소음 예측을 할 수 있을 것으로 기대한다.

In this study, we carried out interrupted cutting of carbon steel for machine structure(SM20C) with uncoated carbide tool and analyzed anova test and confidence interval to find influential factor to surface roughness, and obtained regression equation. Rhe results are follows: First, we found that affected factor to surface roughness in interrupted cutting was feed rate. Secondly, the cutting speed and depth of cut was small affected to surface roughness. Finally, from multi-regression analysis of interrupted cutting experimental result, obtained regression equation and it’s coefficient determination was 0.814 and it means that regression equation was predictable. Compared with other continuous cutting, if feed rate increase, surface roughness will grow in interrupted cutting.

In this study, we were turning STD11 and was carried out to presume for mutual relation of turning condition to get optimum cutting force(principal, radial, feed force) and experimental equation by variance, correlation coefficient and multi regression analysis with whisker reinforced ceramic tool. To predict cutting force, analyze principal, radial, feed force with multi-regression analysis. Results are follows: From the analysis of variance, affected factor to cutting force feed rate, depth of cut, cutting speed in order and cutting speed was very small affect to cutting force. From multi-regression analysis, we extracted regression equation and the coefficient of determination(R2) was 0.84, 0.88, 0.7 at principal, radial and tangential force. It means regression equation is significant. From the experimental verification, it was confirmed that princial, radial and tangential force was predictable by regression equation. Through the analysis of the correlation coefficient between each component forces and surface roughness, the principal force was found to have the greatest impact

In General, the surface roughness of turning is depends on cutting condition which are cutting speed, depth of cut, and feed, etc. This study was carried out to presume for mutual relation of turning condition to get optimum surface roughness and experimental equation by variance and multi regression analysis As the result, multiple correlation coefficient was calculated 97%, the coefficient of determination (R2) was calculated 95% and the adjusted coefficient was calculated 97% by multiple regression analysis So, the formula was made by this multiple regression analysis is reliable.

지구온난화에 따른 한반도 식생구조의 변화에 맞추어 미황사 사찰림의 현 식생구조분석과 종다양성을 고려한 사찰림의 식생학적 구조분석과 적합한 식생구조 선정 및 관리를 위한 연구를 실시하였다. 본 연구는 식물사회학적 식생구조분석, 식생단위와 환경변수와의 상관관계, 생활형구조분석, 종다양성 분석 등을 실시하였다. 현 사찰림은 식물사회학적 식생구조 분석결과 졸참나무-굴참나무 군락, 붉가시나무군락, 팽나무군락의 식생단위로 구분되었으며, 환경변수 Ca, Mg, P 의 기준에 따라서 팽나무군락과 나머지 군락들(졸참나무-굴참나무군락과 붉가시나무군락)의 두 영역으로 분포하였다. 또한 환경변수 유기물(OM), Ni, Zn 에 따라서 졸참나무-굴참나무군락과 붉가시나무군락의 분포와 상관성이 있는 것으로 나타났다. 졸참나무-굴참나무 군락과는 양의 상관관계를 붉가시나무군락과는 음의 상관관계를 가지는 것으로 나타났다. 생활형 R1-2 식물인 조릿대가 관목층 이하에서 우점하고 있으며, 저층부의 종의 단순화를 이루고 있다. 종다양성은 졸참나무-굴참나무 군락이 붉가시나무 군락에 비하여 더 높게 나타났으며, 상록활엽수림으로 이루어진 남은사에 비해서 본 미황사 사찰림의 종다양성이 높게 나타났다. 식물사회학적 분석결과를 통한 식생군락, 조릿대에 의한 저층부 이하의 종의 단순화, 종다양성 및 종균재도를 고려한 미황사 사찰림의 장기적 식생관리가 필요하다 사료된다.

본 연구는 참당귀 재배 시에 발생하는 추대 참당귀를 부산물로 활용가능성이 있는지 평가하기 위해 수행하였다. 추대 참당귀의 지상부와 지하부의 총 무게는 수확기 비추대 참당귀의 지하부 무게 대비 약 98.5%로 높게 나타났다. 또한 추대 당귀의 decursin과 decursinol angelate의 총 함량은 주 생산품인 참당귀 신(身)의 지표성분 총 함량인 4.24%와 대비해 부위별로 0.64%~2.39%로 나타났으며, 이는 추출물로 이용 시 생산품 대비 15~56%에 해당하는 것으로 나타났다. 또한, 항상화 활성의 경우 추대 참당귀는 전반적으로 비추대 참당귀에 비해 우수한 것으로 나타났다. 추대 참당귀의 생산량, 지표성분 함량 그리고 항산화 활성 결과를 고려해 봤을 때, 추대 참당귀의 부산물은 사료 첨가제 및 화장품 용도의 추출물로 이용 가능성이 높은 것으로 생각된다.

Angelica gigas Nakai (AGN) is a traditional medicinal herb especially in Korea. It contains pyranocoumarins, which are major active components including decursin (D) and decursinol angelate (DA). This study was carried out to determine the change in active component content and antioxidant activity depending on the root diameter of AGN. Several processing steps are involved to use AGN roots as medicine. The dried AGN roots are divided into body (B), thick root (TkR), medium root (MR) and thin root (TnR) according to their diameter before cutting into medicine. The recovery rates of each root parts per 100 ㎏ were measured as 32.3±2.5, 9.0±1.0, 39.3±2.1 and 15.0±1.0%, respectively and the mean diameters were measured as 51.95±4.55, 7.05±0.89, 2.88±0.49 and 1.57±0.32 ㎜. Two index components, D and DA, were analyzed. The change of both D and DA content showed a similar tendency. Both D and DA content were increased as the root diameter decreased (higher in TnR). In addition, antioxidant activity was higher in B and TnR, and lower in TkR and MR than control. This study showed that the thinner the root diameter, the higher the D and DA content in AGN roots and that TnR has excellent antioxidant activity compared to other root parts, suggesting that the thinner root part of AGN could be used as a potential material.

Background : Angelica gigas Nakai (AGN) is a perennial plant found in East Asian countries and an crucial medicinal herb especially in Korea. It contains several chemicals like pyranocoumarins, which are major active components including decursin (D) and decursinol angelate (DA), essential oils and polyacetylenes. This study was carried out to determine the change in active components depending on the root diameter of AGN. Methods and Results : Several processing steps are involved to use AGN roots as medicine. The dried AGN roots are divided into body (B), thick root (TkR), medium root (MR) and thin root (TnR) according to their diameter before cutting into medicine. Among them, B and TkR are mainly used as medicine. The mean diameter of dried each root part (B, TkR, MR, TnR) were measured as 51.95, 7.05, 2.88, and 1.57 ㎜, respectively. The water content of each root part was slightly reduced depending on the size of the diameter (higher in B). In addition, the two active components, D and DA, were analyzed by high performance liquid chromatography. The change of both D and DA content showed a similar tendency. Both D and DA content were increased as the root diameter decreased (higher in TnR). Conclusion : This study showed that the thinner the root diameter, the higher the D and DA content in AGN roots, suggesting that the thinner root parts of AGN could be used as potential materials.

Background : Atractylodes japonica koidz (AJ) is a perennial herb that belongs to Atractylodes genus. The dried rhizome of AJ is known as ‘Baek-chul’. The ‘Baek-chul’ is used as important traditional medicine in north-east Asia. It is considered to be effective for the treatment of stomach disorder, virus, diuresis, inflammation, arthritis. AJ is heavily depend on import from china and only few studies have been carried out. In this study, we develop SSR marker to build a foundation of breeding, to analyze genetic diversity and to construct core collection. Methods and Results : AJ resources was collected from each different place. To find simple sequence repeat (SSR) marker, we sequenced genomic DNA of AJ resources using Illumina HiSeq 2000 System. As a result of next generation sequencing (NGS), we obtained putative SSR loci. From these SSR primers, 553 SSR primer sets were designed successfully and confirmed polymorphism by in silico analysis. Nucleotide motifs ranged from tri- to penta-. Among these, 48 primer were tested in 4 individuals by capillary electrophoresis. Finally, selected 28 SSR marker were showed clear band and polymorphism by Electrophoresis. Conclusion : In this study, we developed 28 polymorphic SSR marker using NGS, and it could be used for analyzing genetic diversity of A. japonica. These marker would be useful for breeding of new cultivar in the future.