The electrochemical properties of a CFX cathode were improved by defluorination of the surface with a N2 plasma and using a silica wafer. Compared to the N2 plasma treatment alone, when the CFX and silica were reacted together, the C-F bonds were modified and the surface was etched efficiently, so defluorination was enhanced. An electrochemical analysis confirmed that Half-cells prepared by treating CFx and silica with nitrogen plasma exhibited a capacity of about 400 mAh/g at 5C. In addition, it was confirmed that the loss of charge transfer was reduced by up to 71% compared to that for pristine CFX. As shown by a GITT analysis, when the CFx and silica were treated with N2 plasma together, the ion conductivity gradually increased due to a decrease in the ion diffusion barriers and the formation of a carbon layer. Therefore, this is a simple and effective way to improve the conductivities of CFX cathode materials with the energy of a N2 plasma and the silica-fluorine reaction.

It was found in this study that fluorinated microporous carbon aerogels with enhanced hydrophobicity could be successfully prepared by direct fluorination to separate water-in-oil emulsions at high flux. The fluorinated carbon aerogel (F-CA) surface treated by the fluorination method had a water contact angle of 151.2° and could immediately absorb oil. In addition, the unique network structure of F-CA and its hydrophobicity allow surfactant-stabilized water-in-oil emulsions to be effectively and simply separated under gravity without requiring external forces such as vacuum or pressurization. The network structure of F-CAs consists of randomly connected spherical particles that form fluorinated permeation channels, which induce high flux during emulsion separation. The F-CA spherical particles have nanosized pores and high hydrophobicity, which repel and trap water droplets to increase the separation purity. Therefore, F-CA exhibited excellent performance, such as high filtrate purity (up to 99.9954%) and flux (up to 11,710 L/m2h). Furthermore, F-CA reusability was demonstrated as it did not lose its hydrophobicity and maintained its performance even after repeated use. This type of aerogel has great potential to be utilized throughout various environmental fields, including oil remediation.

The effects of different plasma agent species ( CF4, N2) over the conductivity of CFX cathode material were identified. Both plasma treatments have surface etching effect, while the CF4 plasma treatment has C–F bond modification effect and the N2 plasma treatment has defluorination effect. The changes of surface chemical species and porosity along the plasma agent were elucidated. Moreover, the electrochemical properties of plasma-treated CFX confirmed the effects of plasma treatments. The charge-transfer resistance of plasma-treated CFX was maximum 60.3% reduced than the pristine CFX. The effects of surface chemical modification coupled with etching along the plasma gas agents were compared and identified with their reaction mechanisms.

Fluorine heteroatoms were introduced to increase the limited specific capacitances of electric double-layer capacitors (EDLCs), and the effects of the fluorine atoms were analyzed. To introduce the fluorine, a CF4 plasma treatment was used that introduced the fluorine atoms quickly. Among the fluorine functional groups in the F6-ACA framework, the semi-ionic C–F bonds induced rapid charge transfer and imparted pseudocapacitance. Consequently, we achieved a specific capacitance of 325.68 F/g for the F6-CA sample at 0.5 A/g. By analyzing the contributions of the electric double-layer capacitance and the pseudocapacitance, we determined that the contribution from the pseudocapacitance was 37.57%. A remarkable specific capacitance retention rate of 95.87% was obtained over 1000 charge/discharge cycles with a high current density of 3 A/g. Additionally, the semi-ionic C–F bonds reduced the charge transfer resistance ( Rct) by 36.8%. Therefore, the specific capacitance was improved by the fluorine heteroatoms, and the semi-ionic C–F bonds played a pivotal role in this improvement.

In this study, we investigate the opportunity of using waste tire char as a cathode material for lithium-ion primary batteries (LPBs). The char obtained by carbonizing waste tires was washed with acid and thermally fluorinated to produce CFX. The structural and chemical properties of the char and CFX were analyzed to evaluate the effect of thermal fluorination. The carbon structure of the char was increasingly converted to CFX structure as the fluorination temperature increased. In addition, the manufactured CFX- based LPBs were evaluated through electrochemical analysis. The discharge capacity of the CFX reached a maximum of 800 mAh/g, which is comparable to that of CFX- based LPBs manufactured from other carbon sources. On the basis of these results, the use of waste tire char-based CFX as a cathode material for LPBs is presented as a new opportunity in the field of waste tire recycling.

Removing CO2 gas to address the global climate crisis is one of the most urgent agendas. To improve the CO2 adsorption ability of activated carbon, nitrogen plasma surface treatment was conducted. The effect of nitrogen plasma treatment on the surface chemistry and pore geometry of activated carbon was extensively analyzed. The porosity and surface groups of the activated carbon varied with the plasma treatment time. By plasma treatment for a few minutes, the microporosity and surface functionality could be simultaneously controlled. The changed microporosity and nitrogen groups affected the CO2 adsorption capacity and CO2 adsorption selectivity over N2. This simultaneous surface etching and functionalization effect could be achieved with a short operating time and low energy consumption.

The facile production of high-purity mesophase pitch has been a long-standing desire in various carbon industries. Recently, polymer additives for mesophase production have attracted much attention because of their convenience and efficiency. We propose polyvinylidene fluoride (PVDF) as a strong candidate as an effective additive for mesophase production. The mesophase content and structural, chemical, and thermal properties of pitches obtained with different amounts of added PVDF are discussed. The influence of PVDF decomposition on mesophase formation is also discussed. We believe that this work provides an effective option for mesophase pitch production.

Silicon oxide (SiOx) has been considered one of the most promising anode materials for lithium-ion batteries due to having a higher capacity than the commercial graphite anodes. However, its practical application is hampered by very large volume variations. In this work, pyrolysis fuel oil is the carbon coating precursor, and physical vapor deposition (PVD) is performed on SiOx at 200 and 400 °C (SiOx@C 200 and SiOx@C 400), followed by carbonization at 950 °C. SiOx@C 200 has a carbon coating layer with a thickness of ~ 20 nm and an amorphous structure, while that of SiOx@C 400 is approximately 10 nm thick and has a more semigraphitic structure. The carbon-coated SiOx anodes display better charge–discharge performance than the pristine SiOx anode. In particular, SiOx@C 200 shows the highest reversible capacity compared with the other samples at high C-rates (2.0 and 5.0 C). Moreover, SiOx@C 200 exhibits excellent cycling stability with a capacity retention of 90.2% after 80 cycles at 1.0 C. This result is ascribed to the suppressed volume expansion by the PFO carbon coating on SiOx after PVD.

Artificial graphites have been used in various applications, for example, as anode materials for Li-ion batteries, C/C composites, and electrodes for aluminum smelting, due to their unique mechanical strength and high thermal and electrical conductivity. Artificial graphites can be manufactured by a series of kneading, molding, carbonization and graphitization processes with an additional impregnation process. In this study, the influence of the process variables in the kneading and carbonization/graphitization process on the properties of the resulting carbon block was systemically investigated. During the kneading process, the optimum kneading temperature was 90 °C higher than the softening point of the binder pitch; thus, the binder pitch reached its maximum fluidity. On the other hand, during the carbonization and graphitization process, the structural properties of carbon blocks prepared at different heat treatment temperatures were examined and their structural change and evolution were closely described according to the temperature and divided into low-temperature carbonization and high-temperature carbonization/graphitization. Based on this study, we expect to provide a better understanding of setting the parameters for thermally conductive carbon block manufacturing.