In this study, we introduce the validation of the analysis guidelines through preliminary experiments of the draft analysis guidelines before analyzing waste materials (non-combustible). This validation data was applied the accuracy and efficiency of the separation and analysis for the waste such as steel generated from NPP. Steel (non-flammable) was leached the mixed acid and the leaching solution was separated by using the separation guidelines. Steel was corroded with radioactive RM (Co-60, Cs-137) and mixed acid. After drying, the corroded steel was measured the initial radioactivity by a HPGe detector (10,000 seconds). The sample was inserted in a beaker and leached with mixed acid (10 M HNO3 + 4 M HCl) for 2 hours. In this solution, it added 2 ml of H2O2 to increase the leaching effect. The ultrasonic device was adjusted so that the temperature does not exceed 60°C. After elution, the surface of the sample was washed with pure water. The weight of the sample was measured accurately, and recorded the weight loss rate after infiltration. The leaching sample was measured radioactivity by a HPGe detector (10,000 seconds). It was calculated the recovery rate based on the difference in total radioactivity before and after leaching. Before the test, radioactive RM (Co-60, Cs-137) was radioactive deposited by corrosion, but Cs- 137 was not detected in the initial gamma measurement and only Co-60 nuclides were deposited. The recovery rate test results were confirmed to be about 100%.

In the decommissioning process of nuclear power plants, Ni-59, Ni-63 and Fe-55 present in radioactive waste are crucial radionuclides used as fundamental indicators in determining waste treatment methods. However, due to their low-energy emissions, the chemical separation of these two radionuclides is essential compared to others. Therefore, this study aims to evaluate the suitability of various pre-treatment methods for decommissioning waste materials by conducting characteristic assessments at each chemical separation stage. The goal is to find the most optimized pre-treatment method for the analysis of Ni-59, Ni-63 and Fe-55 in decommissioning waste. The comparative evaluation results confirm that the chemical separation procedures for Fe and Ni are very stable in terms of stepwise recovery rates and the removal of interfering radionuclides. However, decommissioning waste materials, which mainly consist of concrete, metals, etc., possess unique properties, and a significant portion may be low-radioactivity waste suitable for on-site disposal. Considering that the chemical behavior and reaction characteristics may vary at each chemical separation stage depending on the matrix properties of the materials, it is considered necessary to apply cascading chemical separation or develop and apply individual chemical separation methods. This should be done by verifying and validating their effectiveness on actual decommissioning waste materials.

Concrete is the primary building material for nuclear facilities, making it one of the most common forms of radioactive waste generated when decommissioning a nuclear facility. Of the total waste generated at the Connecticut Yankee and Maine Yankee nuclear power plants in the United States, concrete waste accounts for 83.5% of the total for Connecticut Yankee and 52% for Maine Yankee. In order to dispose of the low- to medium-level radioactive concrete waste generated during the decommissioning of nuclear power plants, it is necessary to analyze the radioactivity concentration of gamma nuclides such as Co-58, Co-60, Cs-137, and Ce-144. Gamma-ray spectroscopy is commonly used method to measure the radioactivity concentration of gamma nuclides in the radioactive waste; however, due to the nature of gamma detectors, gamma rays from sequentially decaying nuclides such as Co-60 or Y-88 are subject to True Coincidence Summing (TCS). TCS reduces the Full Energy Peak Efficiency (FEPE) of specific gamma ray and it can cause underestimation of radioactivity concentration. Therefor the TCS effect must be compensated for in order to accurately assess the radioactivity of the sample. In addition, samples with high density and large volume will experience a certain level of self-shielding effect of gamma rays, so this must also be compensated for. The Radioactive Waste Chemical Analysis Center at the Korea Atomic Energy Research Institute performs nuclide analysis for the final disposal of low- and intermediate-level concrete waste. Since a large number of samples must be analyzed within the facility, the analytical method must simultaneously satisfy accuracy and speed. In this study, we report on the results of evaluating the accuracy of the radioactivity concentration correction by applying an efficiency transfer method that appears to satisfy these requirements to concrete standard reference material.

A comprehensive understanding of actinide coordination chemistry and its structure is essential in many aspects of the nuclear fuel cycle, such as fuel reprocessing, waste management, reactor safety, and non-proliferation efforts. Managing radioactive waste generated during the nuclear fuel cycle has recently become more important, accordingly increasing the importance of designing appropriate waste forms and storage solutions for long-term waste disposal. Compared to the increase in the need for understanding the chemistry of major radioactive elements, the information on the local structure of the radioactive elements, especially actinides, remains unknown. To probe this issue, X-ray absorption fine structure (XAFS) can be applied. By analyzing the EXAFS (extended X-ray absorption fine structure) and XANES (X-ray absorption near edge structure), the local structure around atoms can be determined. However, the radioactive properties of the nuclides hindered the measurement of EXAFS and XANES, due to the difficulties of preparation, containment, and transfer of the sample. To measure the EXAFS of various compounds regarding the back-end nuclear fuel cycle, laboratory-based EXAFS (hiXAS, HP spectroscopy) has been introduced which can measure the EXAFS and XANES at the energy range of 5-18 keV. Compounds of Copper (Cu foil, CuO samples), Zirconium (Zr foil), and Europium (Eu2O3) were used for the verification of the laboratory -based EXAFS at a given energy range. The measured EXAFS spectrum of various compounds exhibit good agreement with the theoretical data, showing an R-factor of less than 0.02. It was found that each graph has a first peak corresponding to 2.55Å for Cu foil (Cu-Cu), 1.93Å for CuO samples (Cu-O), 3.23Å for Zr foil (Zr-Zr), and from 2.32Å to 2.34Å for Eu2O3 (Eu-O), which agree well with other values from the literature. From the result, it can be implied that this equipment can be used especially in the back-end nuclear fuel cycle field to enhance the understanding of local structure in radiochemistry.

In Korea, extensive industry-academia-research research has already established many facilities and technologies for materials and chemical experiments on non-radioactive substances. However, few facilities have been built to analyze the physical and chemical properties of substances irradiated through neutron irradiation. Korea is planning to decommission Kori-1 and Wolsong-1 in 2027. Extensive analysis of low-level and intermediate-level materials is required to begin decommissioning these nuclear power plants. The material’s composition and level can be identified by analyzing the structure’s characteristics, and a cutting and decontamination plan can be established based on this. In addition, by conducting a nuclide analysis on the waste generated after cutting, suitability for disposal can be secured, and stable treatment can be performed. Accordingly, the Korea Decommissioning Research Institute (KRID) plans to secure infrastructure (hot cells) to analyze the characteristics of intermediate-level decommissioning waste. The goal is to secure high-dose/high-radiation decommissioning waste processing technology through Korea’s first intermediate-level hot cell, support domestic nuclear power plant decommissioning projects, and secure and verify procedures related to nuclide analysis of intermediate-level using hot cells. In addition, by possessing these material properties and nuclide analysis technology, KRID can have a foundation to conduct continuous research on low- and intermediate-level radioactive materials and decommissioning. The purpose of KRID’s establishment is to use this foundation in the future to improve the technological level of the nuclear industry as a whole through linkage between industry, academia, and research institutes.

Alpha activities can be used for categorization, transportation, and disposal of radioactive waste generated from the operation of nuclear facilities including nuclear power plants. In order to transport and dispose of such low- and intermediate-level radioactive waste (LILW) to the Wolsong LILW Disposal Center (WLDC) at Gyeongju, the gross alpha concentration of an individual drum should be determined according to the acceptance criteria. In addition, when the gross alpha concentration exceeds 10 Bq/g, the inventory of the comprising alpha emitters in the waste is to be identified. Gross alpha measurements using a proportional counter are usually straightforward, inexpensive, and high-throughput, so they are broadly used to assay the total alpha activity for environmental, health physics, and emergency-response assessments. However, several factors are thoughtfully considered to obtain a reliable approximate for the entire alpha emitters in a sample, which include the alpha particle energy of a particular radionuclide, the radionuclide that is used as a calibration standard, the uniformity of film in a planchet, time between sample collection and sample preparation, and time between sample preparation and counting. Korea Atomic Energy Research Institute (KAERI) have evaluated the inventory of radionuclides in low-level radioactive waste drums to send every year hundreds of them to the WLDC. In this presentation, we revisit the gross alpha measurement results of the drums transported to WLDC in the past few years and compare them with the concentrations of alpha emitters measured from alpha spectrometry and gamma spectrometry. This study offers an insight into the gross alpha measurement for radioactive waste regarding calibration source, self-absorption effect, composition of alpha emitters, etc.

To achieve permanent disposal of radioactive waste drums, the radionuclides analysis process is essential. A variety of waste types are generated through the operation of nuclear facilities, with dry active waste (DAW) being the most abundant. To perform radionuclides analysis, sample pretreatment technology is required to transform solid samples into solutions. In this study, we developed a dry ashing-microwave digestion method and secured the reliability of the analysis results through a validity evaluation. Additionally, we conducted a comparative analysis of the radioactivity of 94Nb nuclides with and without the chemical separation process, which reduced the minimum detectable activity (MDA) level by more than 65-fold for a certain sample.

The nuclear fuel that melted during the Fukushima nuclear accident in 2011 is still being cooled by water. In this process, contaminated water containing radioactive substances such as cesium and strontium is generated. The total amount of radioactive pollutants released by the natural environment due to the nuclear accident in Fukushima in 2011 is estimated to be 900 PBq, of which 10 to 37 PBq for cesium. Radioactive cesium (137Cs) is a potassium analog that exists in the water in the form of cations with similar daytime behavior and a small hydration radius and is recognized as a radioactive nuclide that has the greatest impact on the environment due to its long half-life (about 30 years), high solubility and diffusion coefficient, and gamma-ray emission. In this study, alginate beads were designed using Prussian blue, known as a material that selectively adsorbs cesium for removal and detection of cesium. To confirm the adsorption performance of the produced Prussian blue, immersion experiments were conducted using Cs standard solution, and MCNP simulations were performed by modeling 1L reservoir to conduct experiments using radioactive Cs in the future. An adsorption experiment was conducted with water containing standard cesium solution using alginate beads impregnated with Prussian blue. The adsorption experiment tested how much cesium of the same concentration was adsorbed over time. As a result, it was found that Prussian blue beads removed about 80% of cesium within 10-15 minutes. In addition, MCNP simulation was performed using a 1 L reservoir and a 3inch NaI detector to optimize the amount of Prussian blue. The results of comparing the efficiency according to the Prussian volume was shown. It showed that our designed system holds great promise for the cleanup and detection of radioactive cesium contaminated seawater around nuclear plants and/or after nuclear accidents. Thus, this work is expected to provide insights into the fundamental MCNP simulation based optimization of Prussian blue for cesium removal and this work based MCNP simulation will pave the way for various practical applications.

If radioactive plumes are released outside due to loss of containment building integrity during a nuclear power plant accident, these materials might travel with the wind, affecting both the surrounding environment and neighboring countries. In China, most nuclear power plants are located on the eastern coast. Consequently, a radioactive plume generated during an accident could negatively impact even the western part of the Korean Peninsula due to westerly winds. To detect such problems early, respond quickly, and protect residents, a system that can monitor aerial radiation under normal conditions is needed. Additionally, a detection system that can operate in real-time in an emergencies conditions is required. The current method for aerial radiation measurement takes environmental radiation data from a monitoring post 1.5 m above the ground and converts it to altitude. To measure actual aerial radiation, an expansive area is surveyed by aircraft. However, this approach is both time-consuming and expensive. Thus, to monitor radioactive plumes influenced by environmental factors like wind, we need a radiation detector that can gauge both radioactivity and directionality. In this study, we developed a radiation detector capable of assessing both the radioactivity and directionality of a radioactive plume and conducted its performance evaluation. We miniaturized the radiation detector using a CZT (Cadmium Zinc Telluride) sensor, enabling its mounting on unmanned aerial vehicles like drones. It is configured with multi-channels to measure directionality of a radioactive plumes. For performance evaluation, we positioned two-channel CZT sensors at 90 degrees and measured the energy spectrum for angle and distance using a disk-type radioactive isotope. Using this method, we compared and analyzed the directionality performance of the multi-channel radiation detector. We also confirmed its capability to discern specific radioactivity information and nuclide types in actual radioactive plumes. Our future research direction involves mounting the multi-channel radiation detector on a drone. We aim to gather actual aerial radiation data from sensors positioned in various directions.

The nuclear power plant (NPP) decommissioning market is expected to expand not only domestically but also overseas. Proven technologies must be applied to decommission NPP. This is based on Article 41-2, Paragraph 2 of the domestic ‘Enforcement Decree Of The Nuclear Safety Act’. Proven technology refers to technology that has verified that it can be applied in the field through demonstration. In other words, in order to carry out NPP decommissioning, verification must be done. Demonstration refers to reducing technological uncertainty and directly verifying services implemented in the field. From a technology commercialization perspective, demonstration requires an approach based on technology readiness level (TRL) from a technology perspective and market readiness level (MRL) from a market perspective. The characteristics of demonstration also differ depending on the characteristics of each field. The demonstration in the field of nuclear energy is the demonstration of demand matching. This is to confirm the feasibility of the technology in the company’s required environment. In order to perform demonstration, a scenario must be derived by reflecting demonstration design considerations. After evaluating the derived scenario, an actual assessment is conducted using lab-based demonstration/virtual environment demonstration/real environment demonstration. What must be preceded by an actual assessment is confirming the consumer’s requirements. In this study, the necessary environment and requirements of consumer’s to perform NPP decommissioning were reviewed. The domestic decommissioning procedure requirements management system presents decommissioning procedures, potential worker accidents, and worker requirements. In the case of foreign countries, it was confirmed that complex wide need, cost benefit, risk reduction, waste generation, operation, reliability and maintenance (RAM) improvement and quantitative measures were evaluated for the technology to be demonstrated. Also the requirements for demonstrating decommissioning need to a detailed review of actual decommissioning cases. Therefore, a comparison must be made between the requirements based on actual NPP decommissioning cases and the requirements derived from this research process. Afterwards, the empirical research approach proposed by the Ministry of Trade, Industry and Energy was applied. The empirical research approach proposed by the Ministry of Trade, Industry and Energy is to secure a track record over a certain period of time and performance under conditions similar to the actual environment in the final research stage at the TRL level 6 to 8. Through this, it will be possible to confirm the suitability of overseas technology for domestic application.

KHNP is conducting research to decommission Wolsong Unit 1 Calandria. Establishment of preparation and dismantlement processes, conceptual design of equipment and temporary radiation protection facilities, and waste management are being established. In particular, the ALARA plan is to be established by performing exposure dose evaluation for workers. This study aims to deal with the methodology of evaluating exposure dose based on the calandria dismantling process. The preparation process consists of bringing in and installing tooling and devices, and removing interference facilities to secure work space. The main source term for the preparation process is the calandria structure itself and crud of feeders. In the case of the dismantlement process, a structure with a shape that changes according to the process was modeled as a radiation source. It is intended to estimate the exposure dose by selecting the number of workers, time, and location required for each process in the radiation field evaluated according to the preparation and dismantlement process. In addition, it is also conducting an evaluation of the impact on dust generated by cutting operations and the human impact of C-14, H-3, which are specialized nuclides for heavy water reactors. KHNP is conducting an exposure dose evaluation based on a process based on the preparation and dismantlement process for decommissioning Calandria through computation code analysis. If additional worker protection measures are deemed necessary through dose evaluation according to this methodology, the process is improved to prepare for the dismantling of worker safety priorities.

The thermal treatment of radioactive waste attracts great attention. The thermal treatment offers lots of advantages, such as significant volume reduction, hazard reduction, increase of disposal safety, etc. There are various thermal technologies to waste. The developed technologies are calcination, incineration, melting, molten salt oxidation, plasma, pyrolysis, synroc, vitrification, etc. The off-gas treatment system is widely applied in the technologies to increase the safety and operation efficiency. The thermal treatment generates various by-product and pollutants during the process. The dust or fly ash are generated as a particulate from almost every radioactive waste. The treatment of PVC related components generates hydrogen chloride, which usually brings corrosion of facility. The treatment of rubber and spent resin generates sulfur oxide, SOx. The treatment of nitrile rubber generates nitrogen oxide, NOx. The incomplete combustion of radioactive waste usually generates carbon oxide, COx. The process temperature also affects the generation of off gas, such as NOx and/or COx. Various off gas treatment components are organized for the proper treatment of the previously mentioned materials. In this study systematical review on off gas treatment will be reported. Also, worldwide experiences and developed facility will be reported.

The primary purpose of high temperature process of radioactive waste is to satisfy the waste acceptance criteria and volume reduction. The WAC offers the guideline of waste form fabrication process. The WAC is defined as quantitative or qualitative criteria specified by the regulatory body, or specified by and operator and approved by the regulatory body, for radioactive waste to be accepted by the operator of a repository for disposal, or by the operator of a storage facility for storage. The main objective of WAC is to protect staff and general public and environment by the containment of radioactive material, limit external radiation level, and prevent criticality. The WAC also offers systematic management of radioactive waste by standardization of waste management operations, facilitation waste tracking, ensure safe and effective operation of operating facilities, etc. Since the high temperature process for radioactive waste is considered in many countries, lots of codes and standards are considered. In many WACs, compressive strength, thermal cycle stability, radiation exposure stability, free liquid, and leachability are evaluation to understand the effect of solidified form to the disposal facility. In this paper, systematical review on waste form will be discussed. In addition, brief result of characterization of waste form will be compared.

Thermal cutting processes that can be applied to dismantling nuclear power plants include oxygen cutting, plasma cutting, and laser cutting. According to the global trend, research projects are being carried out in various countries to upgrade laser cutting, and many studies are also being conducted in Korea with plans to apply laser cutting processes when dismantling nuclear power plants. However, with the current technology level of the laser cutting process, the maximum thickness that can be cut is limited to 250 mm. Therefore, in this study, a laser-oxygen hybrid cutting process was implemented by adding a laser heat source to the oxygen cutting process that can cut carbon steel with a thickness of 250 mm or more (RV, beam, column, beam, etc.) when dismantling the nuclear power plant. This has the advantage of improving the cutting speed and reducing the cutting width Kerf compared to conventional oxygen cutting. In this research, the laser-oxygen hybrid cutting process consisted of laser cutting to which Raycus’ 8 kW Fiber Laser power source was applied and oxygen cutting to which hydrogen was applied with Fuel Gas. The oxygen torch was placed perpendicular to the test piece, and the laser head was irradiated by tilting 35° to 70°. The effects of cutting directions on quality and performance were studied, and cutting paths were selected by comparing cutting results. Thereafter, it was confirmed that there is an optimal laser output power according to the cutting thickness by studying the effect on the cutting surface quality by changing only the laser output power under the same cutting conditions. The results of this study are expected to be helpful in the remote cutting process using laser-oxygen hybrid cutting when dismantling domestic nuclear power plants in the future.

As the decommissioning of domestic nuclear power plants (Gori Unit 1 and Wolseong Unit 1) becomes more visible, many research projects are being conducted to safely and economically decommissioning of domestic nuclear power plants (NPPs). After permanent shutdown, decommissioning of NNPs proceeds through decontamination, cutting of main equipment, waste disposal and site restoration stages. And various technologies are applied at each stage. In particular, remote cutting of neutron induced structures (RV, RVI, etc.) is a technology used in developed countries in the cutting stage, and remote cutting has been evaluated as a core technology for minimizing workers’ radiation exposure. Generally, remote cutting technologies are divided into mechanical/thermal/electrical cutting. Among various thermal cutting technologies, plasma arc cutting (PAC) is more economical and easily to remote control than other cutting technologies, and is also effective in cutting STS304 plates. PAC is a thermal cutting technology that melts the base material at the cutting area with a plasma arc heat source and removes melted material by blowing it out with cutting gas. The cutting quality depends on the stand-off distance and power (current), material thickness, cutting speed, etc., while double arcing will occur if the cutting conditions are not suitable. A monitoring system that can confirm double arcing during remote cutting is necessary because double arcing can reduce cutting quality, increase secondary waste (increase kerf and aerosol), and cause non-cutting. In this study, we used an ultrahigh-speed camera equipped with a band-pass filter to capture clear arc shapes, and measured voltage waveforms with a data acquisition system. We studied a monitoring method that can confirm the occurrence of double arcing by synchronizing the obtained arc shape and voltage waveform, and the effects of double arcing on the STS304 plates. The results of this study are expected to be helpful in the development of the remote cutting process using plasma arc cutting when decommissioning of domestic NPPs.

The domestic Pressurized Heavy Water Reactor (PWHR) nuclear power plant, Wolsong Unit 1, was permanently shut down on December 24, 2019. However, research on decommissioning has mainly focused on Pressurized Water Reactors (PWRs), with a notable absence of both domestic and international experience in the decommissioning of PHWRs. If proper business management such as radiation safety and waste is not performed, it can lead to increased business risks and costs in decommissioning. Therefore, the assessment of waste volume and cost, which provide fundamental data for the nuclear decommissioning process, is a crucial technical requirement before initiating the actual decommissioning of Wolsong Unit 1. Decommissioning radiation-contaminated structures and facilities presents significant challenges due to high radiation levels, making it difficult for workers to access these areas. Therefore, technology development should precede decommissioning process assessments and safety evaluations, facilitating the derivation of optimal decommissioning procedures and ensuring worker safety while enhancing the efficiency of decommissioning operations. In this study, we have developed a program to estimate decommissioning waste amounts for PHWRs, building upon prior research on PWR decommissioning projects while accounting for the specific design characteristics of PHWRs. To evaluate the amount of radioactive waste generated during decommissioning, we considered the characteristics of radioactive waste, disposal methods, packaging container specifications, and the criteria for the transfer of radioactive waste to disposal operators. Based on the derived algorithm, we conducted a detailed design and implemented the program. The proposed program is based on 3D modeling of the decommissioning components and the calculation of the Work Difficulty Factor (WDF), which is used to determine the time weighting factors for each task. Program users can select the cutting and packaging conditions for decommissioning components, estimate waste amount based on the chosen decommissioning method, and calculate costs using time weighting factors. It can be applied not only to PHWRs, but also to PWRs and non-nuclear fields, providing a flexible tool for optimizing decommissioning process.

After the major radioactivation structures (RPV, Core, SG, etc.) due to neutron irradiation from the nuclear fuel in the reactor are permanently shut down, numerous nuclides that emit alpha-rays, beta-rays, gamma-rays, etc. exist within the radioactive structures. In this study, nuclides were selected to evaluate the source term for worker exposure management (external exposure) at the time of decommissioning. The selection of nuclides was derived by sequentially considering the four steps. In the first stage, the classification of isotopes of major nuclides generated from the radiation of fission products, neutron-radiated products, coolant-induced corrosion products, and other impurities was considered as a step to select evaluation nuclides in major primary system structures. As a second step, in order to select the major radionuclides to be considered at the time of decommissioning, it is necessary to select the nuclides considering their half-life. Considering this, nuclides that were less than 5 years after permanent suspension were excluded. As a third step, since the purpose of reducing worker exposure during decommissioning is significant, nuclides that emit gamma rays when decaying were selected. As a final step, it is a material made by radiation from the fuel rod of the reactor and is often a fission product found in the event of a Severe accident at a nuclear power plant, and is excluded from the nuclide for evaluation at the time of decommissioning is excluded. The final selected Co-60 is a nuclide that emits high-energy gamma rays and was classified as a major nuclide that affects the reduction of radiation exposure to decommissioning workers. In the future, based on the nuclide selection results derived from this study, we plan to study the evaluation of worker radiation exposure from crud to decommissioning workers by deriving evaluation results of crud and radioactive source terms within the reactor core.

The Wolsong unit 1 decommissioning project is the world’s first commercial pressurized heavy water reactor decommissioning project. Although there is a lot of accumulated experience and technology for decommissioning of pressurized water reactors around the world, it can be said that there is great difficulty as there is lack of prior experience and reference materials for pressurized heavy water reactor. On the other hand, if the world’s first pressurized heavy water reactor project is completed, it is possible to enter the overseas market for pressurized heavy water reactor decommissioning. It is also a good opportunity to do so. Accordingly, the current status of operation, plans, and construction of infrastructure related to decommissioning of pressurized heavy water reactors in Canada, which can be said to be the home country of pressurized heavy water reactor, were reviewed. So, this study seeks to present considerations for entering the pressurized heavy water reactors decommissioning market in the future.

Wolsong Unit 1 nuclear power plant, which was permanently shut down in 2019, has a 678 MWe calandria vessel of the CANDU-6 type pressurized heavy-water reactor model. The calandria inside the vault is a horizontal cylindrical vessel made of stainless steel with a length of 7.8 m and a thickness of 28.6 mm. For the entire dismantling processes of a nuclear power plant, dismantling works cannot be performed using only one cutting technology and method, and when performing dismantling of a calandria vessel, various systems and components can be used for cutting and dismantling. The calandria vessel is located in a concrete compartment called a vault, and in order to safely dismantle the calandria vessel, the spread of radioactive contaminants from inside of the vault to the outside must be prevented. We designed dismantling processes using the laser cutting method to dismantle the calandria vessel and end shields. We must minimize the risk of internal radiation exposure to workers from aerosols derived from the thermal cutting processes. Therefore, we need a way to prevent secondary contamination from spreading outside the vault and within the reactor building. The path through which radioactive contaminants move is that the flying airborne products generated during the cutting process inside the vault where the calandria is located do not stay in place but spread outward through the opening of the RM-Deck structure at the top. Therefore, facilities or devices are needed to effectively prevent the spread of radioactive contaminants by blocking the expected movement path. By using these facilities or devices, it is possible to prevent the movement of radioactive aerosol particles between the location of the worker and the location of the cutting area where the calandria is located, thereby preventing internal exposure through the worker’s breathing. In addition, by using these, the cutting area where airborne pollutants are generated can be designed as an isolated work space to prevent the spread of radioactive contaminants. In this study, we propose a method of facilities for confining radioactive aerosol particles and preventing the spread of contamination when thermal cutting of the calandria vessel within the vault.

The radiation field generated in the primary cooling system of a nuclear power plant tends to increase in intensity as radionuclides bind to the oxide film on the internal surface of the primary system, which is operated at high temperature and pressure, and as the number of years of operation increases. Therefore, decontamination of the primary cooling system to reduce worker exposure and prevent the spread of contamination during maintenance and decommissioning of nuclear power plants uses the principle of simultaneous elution of radionuclides when the corrosion oxide film dissolves. In general, a multi-stage chemical decontamination process is applied, taking into account the spinel structure of the corrosion oxide film formed on the surface of the primary cooling system, i.e. an oxidative decontamination step is applied first, followed by a reductive decontamination step, which is repeated several times to reach the desired decontamination goal. Currently, permanganic acid is commonly used in oxidative decontamination processes to remove Cr from corrosion oxide films. In the reductive decontamination step to remove iron and nickel, organic acids such as oxalic acid are commonly used. However, organic acids are not suitable for the final radioactive waste form. A number of multi-stage chemical decontamination technologies for primary cooling systems have been developed and commercialized, including NP-CITROX, AP/NP-CANDECON, CANDERM, AP/NP-LOMI and HP/CORD-UV. Among these, HP/CORDUV is currently the most actively applied primary cooling system chemical desalination process in the world. In this study, KAERI has developed a new chemical decontamination technology that does not contain organic chemical decontamination agents, with a focus on securing an original technology for reducing the amount of decontamination waste while having equivalent or better decontamination performance than overseas commercial technologies, and compared it with the inorganic chemical agent-based HyBRID (Hydrazine Based Reductive Metal Ion Decontamination) chemical decontamination technology.