검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 637

        301.
        2009.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this work, effects of carbon matrix on sliding friction and wear behavior of four kinds of C/C have been investigated against 40 Cr steel ring mate. Composite A with rough lamination carbon matrix (RL) shows the highest volume loss and coefficient of friction, while composite D with smooth lamination/resin carbon matrix (SL/RC) shows the lowest volume loss. The worn surface of composite A appears smooth, whereas that of composite C with smooth lamination carbon (SL) appears rough. The worn surface of composite D appears smooth under low load but rough under high load. Atomic force microscope images show that the size of wear particles on the worn surface is also dependent on the carbon matrix.
        3,000원
        302.
        2009.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        A comparative analysis of the hindered amine light stabilizers (HALS) and UV abosrber (UVA) and their respective photostabilizing effect on wood plastic composites (WPCs) are reported in this study. The influence of accelerated weathering on the mechanical properties of the composites and the microscopic morphology of a degraded layer on the cross section and the surface were studied. UV absorbers were more efficient at preventing composite lightening than was UV stabilizer. The amount of whitening decreased with the increase of photostabilizers. With the addition of a UV absorber (Tinuvin360), the tensile modulus and strength of the composites increased slightly. However, the addition of a light stabilizer (Tinuvin770) and a UV absorber decreased the tensile modulus and strength of the composites. After 250 and 500 hr exposure, tensile modulus and strength of the un stabilized and stabilized composites decreased. The tensile strength of UV absorber (Chimassorb81)-stabilized composites was significantly greater than that of control and light stabilizer (Tinuvin770)- and UV absorber (Tinuvin360)-stabilized composites. UV absorber-stabilized samples showed less whitening and photodegradation than control and light stabilizer-stabilized samples.
        4,000원
        303.
        2009.03 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        In this paper, non-treated ACF (Activated Carbon Fiber) /TiO2 and Zn-treated ACF/TiO2 were prepared. The prepared composites were characterized in terms of their structural crystallinity, elemental identification and photocatalytic activity. XRD patterns of the composites showed that the non-treated ACF/TiO2 composite contained only typical single and clear anatase forms while the Zn-treated ACF/TiO2 contained a mixed anatase and rutile phase with a unique ZnO peak. SEM results show that the titanium complex particles are uniformly distributed on and around the fiber and that the titanium complex particles are more regularly distributed on and around the ACF surfaces upon an increase of the ZnCl2 concentration. These EDX spectra show the presence of peaks from the C, O and Ti elements. Moreover, peaks of the Zn element were observed in the Zn-treated ACF/TiO2 composites. The prominent photocatalytic activity of the Zn-treated ACF/TiO2 can be attributed to the three different effects of photo-degradation: doping, absorptivity by an electron transfer, and adsorptivity of porous ACFs between the Zn-TiO2 and Zn-ACF.
        4,000원
        304.
        2009.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this work, the hydrogen storage behaviors of carbon nanotubes (CNTs)/metal-organic frameworks-5 (MOF-5) hybrid composites (CNTs/MOF-5) were studied. Hydrothermal synthesis of MOF-5 was conducted by conventional convection heating using 1-methyl-2-pyrrolidone (NMP) as a solvent. Morphological characteristics and average size of the CNTs/MOF-5 were also obtained using a scanning electron microscopy (SEM). The pore structure and specific surface area of the CNTs/MOF-5 were analyzed by N2/77 K adsorption isotherms. The capacity of hydrogen storage of the CNTs/MOF-5 was investigated at 298 K/100 bar. As a result, the CNTs/MOF-5 had crystalline structures which were formed by hybrid synthesis process. It was noted that the CNTs/MOF-5 can be potentially encouraging materials for hydrogen adsorption and storage applications at room temperature.
        3,000원
        305.
        2009.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        졸-겔 공정은 비교적 간단하고 사용이 편리하며 저렴한 설비투자비가 소요되면서도 우수한 물성 및 차단특성을 갖는 코팅 박막을 얻을 수 있다는 장점이 있다. 졸-겔 공정으로 코팅된 필름은 산소 등의 영향에 의해 부패되기 쉬운 식품, 음료, 약품, 의약품 등의 포장재나 단열제로 응용 가능하다. 본 연구에서는 aluminum isopropoxide를 출발물질로 하여 alumina sol을 제조한 후 실란 커플링제를 첨가하여 코팅 용액을 제조하였다. 또한, 제조된 alumina sol 용액을 이축연신 폴리프로필렌(BOPP)에 코팅하여 복합 필름을 만들고 산소 투과 특성을 측정한 결과 순수한 BOPP에 비해서 산소 투과도가 약 85% 정도 감소되는 효과를 보였다.
        4,000원
        306.
        2008.12 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        The NO gas sensing properties of ZnO-carbon nanotube (ZnO-CNT) composites fabricated by the coaxial coating of single-walled CNTs with ZnO were investigated using pulsed laser deposition. Upon examination, the morphology and crystallinity of the ZnO-CNT composites showed that CNTs were uniformly coated with polycrystalline ZnO with a grain size as small as 5-10 nm. Gas sensing measurements clearly indicated a remarkable enhancement of the sensitivity of ZnO-CNT composites for NO gas compared to that of ZnO films while maintaining the strong sensing stability of the composites, properties that CNT-based sensing materials do not have. The enhanced gas sensing properties of the ZnO-CNT composites are attributed to an increase in the surface adsorption area of the ZnO layer via the coating by CNTs of a high surface-to-volume ratio structure. These results suggest that the ZnO-CNT composite is a promising template for novel solid-state semiconducting gas sensors.
        4,000원
        307.
        2008.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The factors that influence ablation resistance in fiber composites are properties of the reinforced fiber and matrix, plugging quantity of fiber, geometrical arrangement, crack, pore size, and their distributions. To examine ablation resistance according to distribution of crack and pore size that exist in carbon/carbon composites, this study produced various sizes of unit cells of preforms. They were densified using high pressure impregnation and carbonization process. Reinforced fiber is PAN based carbon fiber and composites were heat-treated up to 2800℃. The finally acquired density of carbon/carbon composites reached more than 1.932 g/cm3. The ablation test was performed by a solid propellant rocket engine. The erosion rate of samples is below 0.0286 mm/s. In conclusion, in terms of ablation properties, the higher degree of graphitization is, the more fibers that are arranged vertically to the direction of combustion flame are, and the less interface between reinforced fiber bundle and matrix is, the better ablation resistance is shown.
        4,000원
        308.
        2008.10 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        BaTiO3/epoxy composites can be applied as the dielectric materials for embedded capacitors. The effects of the degree of BaTiO3 particle agglomeration on the dielectric properties of BaTiO3/epoxy composites were investigated in the present study. The degree of particle agglomeration was controlled by the milling of the agglomerated particles. The size and content of the agglomerated BaTiO3 particles decreased with an increase in the milling time. The dielectric constants and polarizations of BaTiO3/epoxy composites abruptly decreased with the increase of the milling time. It was concluded that the dielectric constants and polarizations of BaTiO3/epoxy composites decreased as the degree of particle agglomeration decreased. The degree of agglomeration of BaTiO3 particles turned out to be a very influential factor on the dielectric properties of BaTiO3/epoxy composites.
        4,000원
        309.
        2008.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        이 논문에서는 단일방향 및 크로스-플라이 섬유강화 복합재에서의 동적 균열 전파를 모사하기 위해 특별히 고안된 스펙트랄 방법의 정식화와 수치적 구현 방법에 대해 제시한다. 이 방법은 균열면에서 작용하는 힘과 변위 사이의 스펙트랄 관계식에 기초하고 있고, 재료는 횡등방성 고체로 가정된다. 본 논문에서 제안된 방법에 의해 섬유보강 복합재에서 전파하는 균열문제가 대해 검토 해석되며, 실험 및 문헌에 나와 있는 결과와 비교된다. 이 방법은 FRP 보강 철근 콘크리트 구조물에서의 균열해석문제에 직접 적용이 가능하다.
        4,000원
        310.
        2008.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        On the base of experience in development of Magnetic Powder Composites, and particularly Soft Magnetic Composites, authors are trying to systematize classification and indicate possible development prospective of Magnetic Nanocomposites (MN) technology and their applications in electrical converters. Clear classification and systematization, at an early stage of any materials and technology development, are essential and lead for better understanding and communication between researchers and industry involved. This concern MN as well and it seems to be the right time to make it at present stage of their development. Presented proposal of classification distinguishes various types of MN by their magnetic properties and area of possible applications. It is not a close set of types, and can be extended due to increase of knowledge concern these nanocomposites.
        4,200원
        311.
        2008.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The Ni-based bulk metallic glass matrix composites were fabricated by spark plasma sintering of mixture of gas-atomized metallic glass powders and ductile brass powders. The successful consolidation of metallic glass matrix composite was achieved by strong bonding between metallic glass powders due to viscous flow deformation and lower stress of ductile brass powders in the supercooled liquid state during spark plasma sintering. The composite shows some macroscopic plasticity after yielding, which was obtained by introducing a ductile second brass phase in the Ni-based metallic glass matrix.
        4,000원
        312.
        2008.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Rubber reinforcing carbon black N330 was treated by physical activation under CO2 to different degrees of burn-off. The mechanical properties indicating the reinforcement of SBR (Styrene-Butadiene Rubber) vulcanizates filled by activated carbon blacks, such as tensile strength, modulus at 300% strain and elongation at break were determined. During CO2 activation of fresh carbon blacks, the development of microporous structure caused an increase of extremely large specific surface area and the porosity turned out to be an increasing function of the degree of burn-off. The tensile strength and modulus at 300% of activated carbon blacks filled rubber composites were improved at lower loading ratios of 20 and 30 phr, but decreased drastically after 30 phr, which is considered that it might be difficult to get a fully dispersed rubber mixture at higher loading ratios for fillers having very large specific surface areas. However, the Electromagnetic Interference (EMI) shielding effectiveness of SBR rubber composites having activated carbon black at 74% yield were improved at a large extent when compared to those having raw carbon black and increased significantly as a function of increasing loading ratio.
        4,000원
        313.
        2008.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Carbon nanotube (CNT)/ composites were synthesized to enhance the hydrogen storage properties. The emphasis was made on the effect of different shortening methods of CNTs on the open-tip structure and the resulting properties. The use of open CNTs as a starting material resulted in an enhanced hydrogen properties of CNT/ composites. Among the employed methods for the shortening of CNTs, wet milling using ethanol was the most efficient, while ultrasonic acid treatment or thermal decomposition resulted in a less hydrogen storage capacity.
        4,000원
        314.
        2008.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Multidirectional reinforcement is aimed primarily at overcoming interlaminar weakness, hence a major interest lies in the mechanical properties of multidirectional carbon/carbon composites. Mechanical properties depend on the type of carbon fiber, the size of the fiber bundle, the spacing of the bundles, the angles of the bundles relative to the axes of the block, and matrix formation. In the present studies, PAN based carbon fiber preforms manufactured different size of unit cell have been prepared. Densification of these used high pressure infiltration and carbonization technique with coal tar pitch as matrix precursor was carried out. Scanning electron microscopy has been used to study the fracture behavior of composites. The size of unit cell of the preforms has considerably affected on the flexural properties as well as microstructure of the carbon/carbon composites.
        4,000원
        315.
        2008.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The effects of fillers on the mechanical and thermal properties of glass/novolac composites have been studied. The matrix polymer and reinforcement were novolac type phenolic resin and milled glass fiber, respectively. Three different fillers, such as calcium carbonate, aluminum oxide, and wood powder were used for glass fiber reinforced plastic(GFRP) manufacture. Gravity, moisture content, tensile and flexural strength were measured to analyze the mechanical properties of GFRP and the final composites was burned in the electronic furnace at 1000℃ to confirm thermal properties GFRP containing aluminium oxide shows the highest thermal stability with 32% of weight loss at 1000℃ for one hour. GFRP containing calcium carbonate shows the maximum flexural strength (146 MPa), but that containing wood powder dose the highest tensile strength (65 MPa). Conclusively, we found that the characteristics of final composites strongly depend on several factors, such as types of materials, contents and chemical affinity of fillers. Therefore, it is very important to set up the combination of fillers for GFRP manufacturing to improve both mechanical and thermal properties at the same time.
        4,000원
        316.
        2008.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구에서는 입자강화 복합재료(particle-reinforced composites)의 거동을 예측하기 위하여 Lee and Pyo(2007)에 의해 제안된 계면손상을 고려한 복합재료의 미세역학 탄성모델과 Karihaloo and Fu(1989)의 미세균열 생성모델을 결합하여, 보강입자의 계면손상(imperfect interface)과 기지 내 미세균열을 고려하여 탄성구성모델(constitutive model)의 거동해석을 수행하였다. 제안된 탄성구성모델의 적용성 검증과 주요손상변수가 거동예측에 미치는 영향을 알아보기 위해 일축 하중 하에서의 응력-변형률 관계를 수치적으로 나타내었다. 또한, 기존의 관련 실험결과와 본 해석결과와의 비교를 통하여 제안된 모델의 정확도를 검증하였다.
        4,000원
        317.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Polypropylene (PP) composites with wood flour/wax/coupling agent were manufactured by melt compounding and injection molding. The influence of wood flour(WF), wax, and coupling agent on the mechanical and thermal properties of the composites was investigated. The addition of wood flour to neat PP has the higher tensile modulus and strength compared with neat PP. The presence of wax also improved the tensile modulus. At the same loading of PP and WF, the addition of coupling agent highly decreased the tensile modulus, and increased the tensile strength. From thermogravimetric analysis (TGA), the addition of wax improved the thermal stability of the composites in the later stages of degradation. The presence of MAPP and wood flour in turn decreased thermal stabilities of composites. From differential scanning calorimetry analysis (DSC), neither the loading of wax. nor the presence of MAPP has shown significant effect on the thermal transition of composites.
        4,200원
        318.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The Cu-based bulk metallic glass (BMG) composites containing Zr-based metallic glass phase have been consolidated by spark plasma sintering using the mixture of Cu-based and Zr-based metallic glass powders in their overlapped supercooled liquid region. The Zr-based metallic glass phases are well distributed homogeneously in the Cu-based metallic glass matrix after consolidation process. The successful consolidation of BMG composites with dual amorphous phases was corresponding to the sound viscous flow of the two kinds of metallic glass powders in their overlapped supercooled liquid region.
        4,000원
        319.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The Cu-based bulk metallic glass (BMG) composite was fabricated by spark plasma sintering (SPS) using of gas-atomized metallic glass powders and ductile brass powders. No defect such as pores and cavities was observed at the interface between the brass powder and the metallic glass matrix, suggesting that the SPS process caused a severe viscous flow of the metallic glass and brass phases in the supercooled liquid region, resulting in a full densification. The BMG composites shows some macroscopic plasticity after yielding, although the levels of strength decreased.
        4,000원
        320.
        2007.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In the present study, Zr-base metallic glass (MG) and Zr-base BMG/diamond composites were fabricated using a combination of gas atomization and spark plasma sintering (SPS). The microstructure, thermal stability and mechanical property of both the specimens as atomized and sintered were investigated. The experimental results showed that the SPSed specimens could be densified into nearly 100% and maintained the initial thermal stability at the sintering temperature of 630K. In addition, MG/diamond powder composites were successfully synthesised using SPS process. The composites, even a very low diamond volume fraction, generated a significant increase in compressive strength. With increasing the diamond volume fraction, the compressive strength was also increased due to the addition of hardest diamonds. It suggests that these composites would be potential candidates for a new cutting tool material.
        4,000원