본 연구에서는 콘크리트내로 침투하는 염소이온을 모니터링하기 위하여, 스크린프리트 기법으로 염소이온 반응형 부식센서를 개발하고, 센서의 세선 수가 부식반응도 및 민감도에 미치는 영향을 실험을 통하여 정량적으로 분석하였다. 개발된 부식센서를 이용하여 염소이온량에 따라 부식 반응도을 확인하였으며, 센서의 파괴정도에 따른 저항변화에서는 단선형 센서보다 다선형 센서에서 큰 저항 변화를 나타내었다. 또한, 부식센서는 NaCl 수용액의 농도가 높은 만큼 센서의 저항변화가 크고, 콘크리트 내에서 센서 종류에 따른 부식저항은 단선형보다 다선형에서 민감도가 높게 나타났으며, 센서의 매설깊이가 클수록 저항변화 사이클 (cycle)은 증가하였다. 이상의 결과로, 본 연구에서 개발된 부식센서는 염분에 대한 부식반응과 민감도, 저항의 변화를 감지할 수 있었으며, 특히 7세선이 우수한 결과를 나타내어, 염분의 침투정도를 모니터링 하는데 가장 적합하다고 판단된다.

해수중 환경에서 콘크리트 구조물 내에 매립된 철근은 용존산소의 부족으로 부식이 잘 발생하지 않는다. 이 때문에 해수중 환경의 부식촉진시험은 전기화학적인 방법으로 실시되어, 실제 부식 메커니즘과 맞지 않고 장기거동과의 상관성 도출도 어려운 실정이다. 본 연구에서는 해수중 환경에서의 부식촉진시험법을 정립하기 위해 온도와 염화물농도를 주된 변수로 부식촉진시험을 실시하였다. 부식의 발생 유무는갈바닉 전위측정법과 반전지전위법을 통한 철근부식모니터링 결과로 판단하였다. 부식촉진시험 결과 온도의 영향이 가장 지배적이라고 평가되었다. 염화물량은 시험 시편의 깊이별 염화물 농도를 측정하였다. 동일한 조건으로 FEM 내구성 해석 프로그램인 DuCOM을 통해 염화물침투 해석을 실시하여 입증하였다. 또한, 인공해수 침지 조건에 따른 용존 산소량은 실험을 통해 구했으며 이를 통해 부식촉진시험 결과의 타당성을 검증하였다.

최근 ‘먹는 물’에 대한 인식이 높아지고 양질의 물에 대한 요구가 이어짐에 따라 정수처리 시설은 수처리 시설을 확대하고 있다. 이에따라 수처리시설에 적용되는 콘크리트 구조물 내부 방수⋅방식재의 개발 및 기준 마련의 필요성이 높아지면서 최근 활발한 연구가 진행중이다. 하지만, 주로 상도의 내구성 향상에 집중된 연구의 한계성으로 콘크리트 표면과 하도 (프라이머)와의 부착력에 대한 연구가 부족한실정이다. 이에 본 연구에서는 수처리시설의 내부 방수⋅방식재로서 사용되는 프라이머와 콘크리트 표면간의 부착력을 확인하고, 콘크리트 표면 상태 (건조 상태, 습윤 상태, 수압상태)에 따른 부착강도 및 특성에 대하여 알아보고자 한다.

The pilot plant experiment was performed to investigate phosphorus and nitrogen removal from domestic wastewater by MLE process combined with aluminum corrosion reactor. When operating 0.5Q and 1Q to internal recycle and sludge recycle in the MLE process, the effluent CODMn concentration of internal recycle 0.5Q were higher than internal recycle 1Q, the removal efficiency rates of NH3-N in the internal recycle 0.5Q were was higher than internal recycle 1Q. Denitrification rates were about 86.8% in internal recycle and sludge recycle 0.5Q. When operating 0.5Q to internal recycle and sludge recycle in the MLE process, the removal efficiency rates of total nitrogen was the highest. The removal efficiency rates of total phosphorus was about 91.5% in the aluminum corrosion reactor.

This study is based on the electrochemical theory which aims to get the quantitative evaluation about corrosion protection of Zn-Sn metal spray method. The various existing corrosion resistance method and various mixture ratio of Zn-Sn metal spray method is applied with structural steel which is measured change of polarization resistance and corrosion potential. So corrosion protection of Zn-Sn metal spray method is tested. Consequently, coating side of Zn-Sn metal spray method was lower than electric potential of a structural steel adhesion side. So, Galvanic Protection of Zn-Sn metal spray found that structural steel advanced system. Accordingly, Zn-Sn metal spray method is expected as corrosion protection technology excellent in corrosion prevention of structural steel.

The purpose of this study is to evaluate the corrosion protection properties of Zn/Sn metal spray method according to the contents ratio of Zn and Sn by CASS test. Also, the corrosion protection life of Zn/Sn metal spray method is evaluated by the comparing between the corrosion properties of Zn metalizing method and Zn/Sn metal spray method using CASS test. As a result, it was confirmed that the optimum content ratio of Zn/Sn in metal spray method is 60:40(65:35) (Zn : Sn volume ratio) in aspect of corrosion protection properties and construction properties. Also, it was confirmed that the Zn/Sn metal spray method had more than 3 times of corrosion protection properties cmparing the Zn matalizing method.

Post-installed anchor is installed in non-cracked concrete after corrosion to investigate pullout strength of the anchor. Pullout test was conducted diameter, insertion depth of the anchor of a couple of variables. If it receive pullout load, performance of corroded anchor is degraded by the reduction of the cross-section of the anchor body.

The corrosion is a main cause of degradation damage in the steel bridges. The evaluation whether the repair or reconstruction would be need or not for the corroded steel member, is based on cross section and quantity of corroded portion. It is considered reasonable that the evaluation will be base on the endurance of the corroded member. In this study, the bending endurance of the I-shaped steel girder with the local corrosion on the lower flange is discussed by using elastic-plastic finite element analyses. That simple way of estimating it is also proposed.

Severe corrosion damage on the deck surface of a orthotropic bridge deck with bulb rib has been reported in Japan. Therefore, in this study, structural behaviors of a orthotropic bridge deck was numerically examined using FE analysis program MARCment2010. Thus, its deck thickness was decreased according to corrosion damage level of the deck. The deformations and the stress distributions of a orthotropic bridge deck with bulb rib were compared and evaluated.

In this study, performance of the post-installed anchor system was evaluated with reduced strength of concrete and anchor. One of the post-installed anchors was selected to performance evaluation. Concrete strength was reduced by freeze-thawing test, and the post-installed anchor strength was reduced by corrosion test. The post-installed Anchor was installed in concrete of freezing and thawing and original concrete, and corroded anchor was installed in original concrete only. Anchor diameter and installation depth of the anchor were the variable for each specimen. Performance of post-installed anchor system of each specimen was evaluated by pullout test. Anchor diameter and installation depth of anchor, it may affect the performance of the post-installed anchor system from the experimental test results. Fracture mode of each post-installed anchor system had occurred differently depending on the durability of concrete and anchor. The anchor pullout strength from the experimental test results was used in order to compare with the results of CCD (Concrete Capacity Design) method, and CCD equation was modified. Modified equation was able to predict the anchor pullout strength of post-installed anchor system in Original concrete and freezing and thawing of concrete.

In this study, corrosion potential (Ecorr), corrosion rate, and polarization resistance were measured aimed at inorganic inhibitors (passive film type) and organic inhibitors (absorption type). The experiment was conducted using potentiostat for the variable molar ratio and chloride ion concentration of the components of inhibitors in an aqueous solution of saturated calcium hydroxide targeting corrosion. As a result, it was possible to ensure an anticorrosive performance of at least a 1.2 molar ratio of inorganic inhibitors. Also, the organic inhibitors ensured the prevention of the anticorrosive performance of at least about a 0.3 molar ratio. It also showed the tendency that between polarization resistance and corrosion rate, Ecorr and corrosion rate is inversely proportional to the linear. Conversely, the tendency between polarization resistance and Ecorr is proportional to the linear. Also, a distinct difference in organic and inorganic inhibitors’ relationship to Ecorr, corrosion rate, and polarization resistance was not shown.

In case of reinforced concrete based structures, deterioration is mainly due to corrosion of steel rebar. So, the advanced construction rebar materials which have high resistance to corrosion should be developed with the application techniques. In Korea Institute of Construction Technology, the research project on hybrid reinforcing bars have performed since 2013 during 5 years. In this paper, the verification methodologies on corrosion and durability which will be applied to developed hybrid reinforcing bars are suggested

In this study, tensile and axial buckling strength of corroded steel plates was evaluated based on the axially loading tests of corroded specimens, which were cut off at a temporary steel structures. The tensile and axial buckling strength of corroded specimens and non-corroded specimens could be evaluated identically by using effective thickness, which is equal to average thickness minus standard deviation of residual thickness.

To assess the steel corrosion resistance for Calcium aluminate cement and Ordinary portland cement against internal chloride ions, mortar specimens were cast, assuming aggregates are inert. Linear polarisation, half-cell potential and mass loss were chosen to measure the rate of steel corrosion.

In this study, in order to comprehend performance of corrosion inhibitor, the experiment study was conducted about corrosion characteristic 3 steps(0.0, 0.6, 1.2) of Chloride by added amount of inorganic(Ca(NO2)2) and organic(DMEA) corrosion inhibitor by the corrosion inhibitor types about 0.6kg/m3, 2.4kg/m3 based on Chloride ion content 1.2kg/m3 for service life prediction of concrete structure by using Poteniostat. As a results, the excellent anti-corrosive performance of organic corrosion inhibitor was seen that absorption types organic corrosion inhibitor has excellent anti-corrosive performance compared to the inorganic nitrous acid corrosion inhibitor by the added amount of corrosion inhibitor