본 연구에서는 개량형 공압식 가동보를 대상으로 가동보의 기립 각도변화에 따른 잠김흐름 특성을 분석하고 유량계수를 산정하였다. 실험결과, 위어마루에서 하류수면까지의 높이와 위어마루에서 상류 수면고 높이의 비()에 대한 유량감소계수()의 변화는 가1에 가까울 수록 감소하였다. 따라서 보 하류에서의 수심은 상류보다 작지만 보를 통과하는 흐름으로 인해 하류 유속이 빠르게 나타났으며, 유량이 증가할수록 상·하류 수위차는 감소하는 것으로 나타났다. 또한 같은 유량조건인 경우 하류수두는 가클수록 크게 증가하였다. 개량형 공압식 가동보의 잠김흐름 유량계수는 가동보의 물리적 제원보다는 상류 접근흐름수두와 상·하류 흐름조건에 의하여 결정되었

In this study, the recycling processes of construction and demolition waste (C&D waste) were analyzed, and its national recycling rate was determined using material flow analysis (MFA). Available statistical data provided by Ministry of Environment and Korea Environment Corporation were used for the MFA study. The collected data were carefully examined and validated by field investigations. System boundary for MFA covered from waste generation from construction sites to final disposal in 2013. The field investigation showed that recycled aggregate is produced through mechanical shredding, separation, and screening processes of C&D waste. The production efficiency (or process yield) was estimated to be approximately 81.2% on average. The foreign materials in the waste accounted for 18.8% by weight. The separated impurities were sent to recycling facilities, incineration facilities, or landfill sites, depending on the physicochemical characteristics. Efficiency of recycling facilities and the statistical data were integrated to estimate the national actual recycling rate, which turned out to be 87.7% in 2013. Approximately 49.1% of the construction-related waste was recycled as recycled aggregate for concrete production and road base layer for asphalt pavement. Based on the result of MFA, there is 9.8% difference between the actual recycling rate in this study and reported recycling rate by national statistics. In the future, more various C&D waste treatment and disposal facilities, along with aggregate recycling facility, should be investigated to verify the actual recycling rate determined by this study. Statistical accuracy should be further refined through additional field investigations. Our findings can be applicable to development of recycling policies and best management practices for C&D waste streams.

일반적으로 쇠살대 빗물받이는 도로 표면유출 흐름을 차집하여 도시배수 시설로 배제하기 위하여 설치된다. 빗물받이의 규모 및 설치간격 을 결정하기 위하여 빗물받이 차집유량 산정식이 필요하다. 그러므로 쇠살대 빗물받이 유입구의 차집능력 분석이 필요하다. 본 연구에서는 도로 빗물받이의 차집유량 산정을 위해 수리실험모형을 제작하여 720회의 실험을 실시하였다. 빗물받이 제원은 현재 대부분의 국도에 설치 되는 크기인 40×50cm,40×100cm 및 40×150cm를 Froude 상사법칙을 이용하여 1/2로 축소 모형을 제작하였다. 측구의 유량은 도로의 차선 (2~4차선), 경사(도로 종경사 2~10%, 측구 횡경사 2~10%) 및 설계빈도(최대 30년)을 고려하였다. 실험 결과 측구의 횡경사가 커질수록 빗물받 이로 유입되는 유량은 증가하였으며, 빗물받이 유입부의 길이가 증가함에 따라 유입부 측면부를 통한 횡유입량을 증가시켜 빗물받이 유입부의 차집효 율을 증가시켰다. 실측 차집유량을 이용하여 회귀분석 실시하여 빗물받이 유입구 크기별 차집유입량 산정식을 도출하였다. 기존 경험식과 비교한 결 과, 도출된 산정식은 상향된 빈도를 반영한 빗물받이 유입부의 차집유량을 보다 정확하게 산정하였으며, 도로 배수시설 설계에 기초자료로 활용이 가 능할 것으로 판단된다.

This study, examines the flow characteristics of upstream channel depending on water gate operation of Nakdan Multi-fuctional weir. The specific purpose of this study are to simulate the variation of flow velocity depending on the operation of the weir using 1-dimensional hydraulic model, HEC-RAS, and compare it with observed velocity. For discharge conditions from 50 ㎥/s to 3,500 ㎥/s, it is observed that the velocity of upstream channel is almost constant, whereas for probability flood discharge, the velocity and froude number are increased as the discharge values are increased. The velocity values for downstream boundary condition EL, 40.0 m are more decreased than those for EL. 40.5m. From comparison on the variation of water stage depending on water gate operation, it is observed that the stage values are almost constant for discharges below 300 ㎥/s, whereas 5 cm to 20 cm for discharges over 700 ㎥/s. Flow velocity at streamflow gauging station. Nakdong, is decreased by more than 875% after installing the weir. The results obtained from this study indicate that the velocity of upstream channel is decreased and the discharge and velocity of downstream channel are significantly varied after installing the weir.

In this study we conducted a material flow analysis (MFA) of the four major types of waste electrical and electronic equipment (WEEE), namely refrigerators, TV sets, washing machines, and air conditioners, based on the most reliable data available from the Eco-Assurance System, other governmental sources, the literature, a field survey, and interviews. A MFA of six major components, iron, copper, aluminum, plastics, precious metals, and rare metals was also conducted. The estimated total generation of WEEE in 2013 amounted to 401.8 thousand tons, of which 3.8% (or, approximately 5% including printed circuit boards) was exported and 55.0% was recycled. The collection by the formal take-back system occupied 34.6% of the total generation, from which 83.9% was recovered as valuables. The six major components amounted to 299.7 thousand tons, among which 89.8% of iron, 91.4% of copper, 56.0% of aluminum, 27.1% of plastics, 37.1% of precious metals, and 6.2% of rare metals were recovered. A high positive correlation was found between the amount of WEEE flowing into the private recycling business and its economic value. Since the recovery ratio in the private sector was estimated to be much lower, while the potential environmental impact was higher, an optimal strategy was identified to enhance the collection by the public sector. Providing economic incentives should be an effective means to encourage private collection through the formal take-back system.

Recently, localized rainfalls and torrential typhoons due to the abnormal climate have increased in Korea and the damage situation caused by debris flow at Umyeon Mountain has especially take place a big social issue. However, the standardized damage investigation does not yet exist and the systematic analysis of the data has not also been carried out. In this regard, this study developed assessment factors to conduct standardized damage investigation for debris flow. To achieve this, preliminary assessment factors were derived from analysis of literature review and the Delphi method through 12 experts who work at fields of facility, academia and industry. As a result, 29 rational check lists of 6 groups were determined.

In this paper, analyzed the effect on repair mortar by anhydrite blain, by observing workability.

This paper describes the influence of recycled materials on the flowability of steel fiber-reinforced cement composites. For the FRCC, fly-ash and recycled sand were used as recycled materials. The recycled materials were mixed with replacement ratios of 25% and 50%. As reinforcing fiber for the FRCC, micro steel fibers were used. Based on the test results, flowability of FRCC was improved when fly-ash was replaced. Increase of recycled sand had FRCCs exhibited lower flowability.

The purpose of this study is to analysis the materials flow of steel cans from producing to discarding, finding problems in materials flow diagram in performance recycling of steel cans, and improvement ways for relevant systems and policies. Through supply various statics in KECO, it was found that the amount of steel calculated in Korea is 80,555 thousand tons. This amounts is reused from steel scrap of 35,143 thousand tons. After that producing steel was manufactured to steel plate, and manufactured steel plate produced steel cans of 273 thousand tons. The steel cans of 103.2 thousand tons was released in Korea. The 89.5 thousand tons of wastes for recycling was 86.8% for total of 103.2 thousand tons for recycling. The amount of recycling was assumed that there is no loss in collection, sorting and packing stage. According to such studies, a materials flow diagram was drafted and the problems in recycling for each stage were reviewed. In consequence plan to improve consist of materials and structure in cans in production stage, plans to restrict inclusion of foreign particles in discardment and selection section, plan to provide different support in funding and granting quality ratings in the sorting and compression section was suggested.

본 연구는 식재된 개수로에서 흐름특성을 모의할 수 있는 수심 적분된 2차원 수치모형을 이용하여 원형 식생역 주변의 흐름을 수치모의하였다. 식생영향을 고려하기 위해 식생항력 항을 지배방정식에 추가하였고 다양한 식생체적비율(SVF) 조건에 따른 수치모의를 수행하였다. 흐름이 원형 식생역을 통과하고 하류에 저유속 구간인 후류영역(wake region)을 형성하며 식생체적비율이 0.08 이상이면 재순환 영역이 발생하였다. 재순환 발생위치는 식생체적비율이 감소하면 식생역 에서 더욱 하류로 이동하였다. 후류영역을 지나 원형 식생역 양 측면에서 유발된 전단층들의 상호작용에 의해 von Kármán 와열이 발생하였다. 원형 식생역 하류에서 발생하는 와류는 식생체적비율이 0.08 이상이 되면 나타나기 시작하였고 발생위치는 난류운동에너지가 최대값을 보이는 위치와 일치하였다. 최대 난류운동에너지는 식생체적비율이 감소하면 줄어드는 것으로 나타났고 최대값의 발생위치는 점점 하류로 이동하였다.

With the increasing use of pumping to place concrete, the development and refinement of the industry practice to ensure successful concrete pumping is becoming an important need for the concrete construction industry.

In bridge lifting apparatus by using the existing pressure control, unequal lifting inevitably occur due to non-uniform load of the upper structure. In order to solve this problem safety of bridge lifting apparatus using flow control system was evaluated. As a result, the load of each supports for bridge upper structure is measured at the range of 1,098 ~ 2,362 kN and lifting displacement uncertainty was within 0.5 mm observing not any cracks.

The damage cases by debris flow and each investigation techniques used by the institutes associated with debris flow were analysed. It was concluded that considering urban debris flow characteristics and the purpose of investigation is essential to establish reasonable debris-flow damage investigation technique.

Environmental concerns regarding mercury-containing fluorescent lamps have been raised in many countries, especiallyafter International Minamata Convention on Mercury in 2014. Improper management and disposal of the waste such aslandfilling and incineration may pose serious threats to the environment and human health. In Korea, mercury-containinglamps have been regulated by the expanded producer responsibility (EPR) system since 2004. However, only less than30% of the lamps sold to consumers has been collected by municipalities. In order to provide additional measures relatedto proper management of fluorescent lamps, there is a need for a quantitative material flow study by life cycle stage. Inthis study, material flow analysis was conducted by collecting relevant data from literature review, available statistics,and field site visits to lamp recycling facilities. According to the results of this study, approximately 150 million unitsof fluorescent lamps were put on the market in 2013, while 36.9 million units of the lamps were recycled mainly fromhouseholds in the year. It is estimated that approximately 3.5 million units and 2.3 million units of lamps in disposalbags are disposed and treated in landfills and incineration facilities, respectively. This study also found that there weresignificant amounts of uncollected lamps that were present in industrial sectors. The material flow of the industrial sectorsare largely unknown and not properly regulated by government. Based on the mass flow of mercury in lamps, 1.6ton ofmercury in lamps came into consumer markets in 2013. Approximately 407kg of mercury was collected by the recyclingprocess at the fluorescent lamps recycling facility. The mercury disposed in landfills and treated in incinerators were foundto be 38.3kg and 25.5kg, respectively. Further study may be warranted to focus the material and mercury flow of lampsin industrial sectors in order to accurately determine the final destination and disposal of such waste in the environmentbecause there are very few available statistical data regarding distribution flow and treatment of lamps in the sectors.

국내 MMORPG 온라인게임 시장의 동향을 보면 이용자들의 트렌드 변화와 모바일게임 및 해외 게임의 강세로 성장이 정체되어 있는 실정이다. 이렇게 국내 게임이 성장하지 못하는 근 본 원인은 변화 없이 기존 게임 형태 그대로 양산되어 출시되는 현 시장의 잘못된 모순과 각종 플레이로 인해 생기는 문제점들이 서비스 실패의 주원인이다. 이에 본 논문에서는 게임 디자인 의 변화를 주기 위한 방법으로 시나리오의 중요성 및 필요성을 입증하고 기존 게임이 가지고 있는 문제들을 이용자들의 의견수렴과 성공한 국내 및 해외 게임들을 비교 분석하여 새로운 타 입의 TIME FLOW 시나리오를 제안하고자 한다. 이 기법은 게임 내 시간이 흘러 환경과 스토 리가 자연적으로 변화되면서 그에 따른 수많은 콘텐츠를 이용자들에게 제공하게 되는 시스템 설계 구축을 목표로 한다. 이를 통해 새로운 형태의 게임 제작 환경 틀을 설계하고 교육적인 인재 양성 효과를 기대한다.

본 연구에서는 하도 내 수제 형 수리구조물을 설치하였을 때, 만곡수로와 수충부에서의 흐름 양상 변화를 3차원 유속 측정을 통해 확인하였다. 연구를 위해 길이 24.4m, 폭 1.5m, 하상경사 2%의 만곡수로에서 실험을 수행하였다. 실험은 단일 수제의 설치 여부에 따라 크게 두 가지 경우로 나누어 수행하였다. 유속의 측정에는 3차원 초음파 유속계(Acoustic Doppler velocimeter, ADV)를 사용하였으며 각 단면 당 약60개의 측점을선정하여 일정한시간 동안측정하였다. 측정된 유속들은시간평균하였으며, 각단면에서의측정결과를연결하여만곡수로의수면유속을파악하였다. 그결과, 수제설치로 인해구조물하류에위치한만곡부외측에서의유속이현저하게감소하였고제방을향했던흐름의방향이내측으로변화하 였음을 확인할 수 있었다.

Neodymium(Dysprosium)-permanent magnets (Nd(Dy)-Fe-B Magnets) have necessity and potential to be recycled given their high criticality and important roles in various high-tech fields as well as the characteristics of being selectively disengaged from the assemblies in which they are used. This study focused on secondary material flow (downstream) of Nd(Dy)-Fe-B Magnets in South Korea. The quantitative information includes the primary data of each category (Emission - Collection - Disengagement - Resource Recovery - Remanufacturing) with domestic recycling situations of the magnets, which can contribute to more effective policy-making. As a result of the material flow analysis, this study provides the primary data of Nd and Dy at each stage and inhibiting factors (bottleneck) of Nd-Fe-B Magnets recycling and suggests the method for improvement of recycling of rare earth magnet.

강우에 의한 세류간 토양침식은 운동에너지를 갖는 빗방울이 지표면을 타격하여 발생하는 빗물튀김의 박리현상과 지표유출수의 면상흐름에 의한 토사입자의 운반으로 구분할 수 있다. 강우운동에너지는 토양입자를 토양체로부터 분리시키기 위한 강우의 잠재적인 능력의 지표로 널리 사용되고 있다. 본 연구에서는 강우운동에너지가 세류간 토양침식에 미치는 영향을 파악하기 위해 강우의 충돌을 제어하는 스트립 커버를 이용한 토양침식 강우모의 실험을 수행하였다. 강우모의에 의한 강우운동에너지는 자연강우에 비해 0.58배 규모로 재현되었다. 강우강도가 증가함에 따라 지표유출량은 증가하고 지표하유출량은 상대적으로 감소하였다. 지표커버가 없는 사면으로부터 발생한 지표유출량이 지표커버가 있는 경우에 비해 평균 1.82배 증가하였다. 강우운동에너지는 지표유출 및 지표하유출 발생시간에도 영향을 끼쳤다. 빗물튀김과 면상흐름의 상호작용으로 토사유출량이 3.6∼5.9배 증가하였으며 그 증가폭은 강우강도의 증가에 따라 감소하였다. 단위수류력과 토사유출량의 관계분석 결과 강우운동에너지는 빗물튀김에 의한 토양입자의 분리침식을 증가시킬 뿐만 아니라 지표유출수 증가에 따른 토사이송능력을 가중시켜 토사유출량을 크게 증가시키는 것으로 확인되었다.

기포가 포함된 다상흐름의 측정은 중요함에도 불구하고 많은 제약이 있었다. 특히, 공극률이 높은 다상 흐름은 밀도차의 급격한 변화와 두꺼운 공기-물 경계면으로 인해 측정이 매우 어렵다. 본 연구에서는 공극률에 상관없이 기포흐름을 측정할 수 있는 기포영상유속측정법과 다발 광섬유유동측정계를 소개하고자 한다. 기포영상측정기법의 경우, 화상측정시 발생하는 원근에 의한 오차를 최소화하고 추정할 수 있는 피사계 심도에 대한 계산방법을 제시하여 정도 분석을 위한 방안을 제시하였다. 다발 광섬유유동측정계는 얇은 광섬유의 특성을 이용해 다발로 제작하여 측정률을 증가시키고자 하였다. 제시된 두 기법을 기포플룸에 적용하여 신뢰도를 검토하였으며 잘 일치하는 것을 확인하였다. 소개된 기법으로 대표적인 하천 다상흐름인 도수흐름을 측정하여 그 적용성을 검토하였다.

Genetically modified (GM) crops have never been cultivated commercially in Korea, it is necessary for a thorough assessment of the risks associated with their environmental release. We determined the frequency of pollen mediated gene flow from disease resistant GM rice (OsCK1) to non-GM rice (Nagdongbyeo) and weedy rice (R55). A total of 449,711 or 164,604 seeds were collected from non-GM and weedy rice, respectively which were planted around OsCK1. Resistance of the hybrids was determined by repeated spraying of herbicide and DNA analysis using specific primer to confirm hybrids. Though non-GM rice and weedy rice have similar flowering time, the hybrids were found only in non-GM rice and out-crossing ranged from 0.018% at 0.3 m to 0.013% at 0.6 m. All of hybrids were located within 0.6 m distance from the GM rice plot in southerly direction. The meteorological factors including temperature and relative humidity during flowering time were found to be the most important factors for determining rice out-crossing. It should be considered many factors like the local weather condition and flowering time to set up the safety management policy to prevent pollen mediated gene flow between GM and conventional crop.