해상풍력발전 시장의 성장과 함께 해상풍력발전기 설치 선 시장에 대한 기대감이 커지고 있다. 해상풍력발전 시장 내 2030년까 지 약 100척의 설치 선이 필요할 것으로 전망되고 있다. 척당 가격이 3,000∼4,000억 원이라서 일반 운반선보다 고부가가치 시장이다. 특 히, 풍력발전기 용량이 11MW 이상의 대형 설치 선의 수요가 커지고 있다. 중국을 중심으로 아시아 해상풍력발전기 시장의 급성장으로 이 지역에서 운용 가능한 설치 선에 대한 발주에 대한 협의가 많다. 아시아권역 대부분의 해저 지질은 지지 반력이 작은 점토층으로 구성되 어 있다. 이러한 특성에 의해서 설치 선이 작업을 위해 수면 밖으로 오르고 내림 시 스퍼드캔(Spudcan)과 레그(Leg)의 관입 깊이가 크게 발 생한다. 연구에서는 최소 3m에서 최대 21m까지 관입 변수를 이용하여 관입 깊이에 따른 고유 진동 주기, 레그의 구조 안전성 평가 그리고 전복 안전성 지수를 평가하였다. 관입 깊이가 증가하면 고유 진동 주기가 짧아지고, 레그의 모멘트 길이가 짧아져서 구조 강도의 여유 치 가 증가한다. 모든 입사각에서 전복 모멘트에 대해 안전하며, 최댓값은 270도에서 발생한다. 본 연구를 통하여 검토된 조건들은 연약 지반 에서 설치 선의 운용 절차서를 작성 시 관입 깊이에 따라서 레그를 어떻게 운용해야 하는지 판단할 수 있는 중요한 자료로 활용할 수 있 다. 결론적으로 관입 깊이에 따른 레그 구조 안전성을 정확히 파악하는 것은 설치 선의 안전과 직결된 문제이다.

High-performance vehicles with V6 or higher are designed with a dual exhaust system to satisfy both performance and quietness at the same time, and have a confluence geometry for the purpose of stably maintaining the back pressure inside the pipe. The exhaust system generates noise and vibration under the influence of the rotating engine. In particular, in a state such as idling, vibration occurs in a certain frequency range, which may affect the natural vibration of the exhaust system. Therefore, in this study, the optimal shape is proposed by comparing the ignition frequency calculated based on the vibration measurement result in the idle state and the numerical analysis result.

본 연구에서는 중앙 개구부를 갖는 카본나노튜브/유리섬유/폴리머 합성 복합 적층쉘을 다루었다. 수정된 Halpin-Tsai 모델과 마이크로 역학적 접근방법은 단일벽 탄소나노튜브의 합성 비율에 따른 탄성적 물성변화를 추정하기 위하여 적용되었다. 유한요소 해석을 통하여 쉘의 고유진동 및 모드 특성을 분석하였다. 탄소나노튜브의 무게 비율, 보강섬유 각도, 개구부 크기, 고 유진동수 및 고유모드의 상관관계를 규명하였다. 개구부를 갖는 경우와 갖지 않는 경우에 대하여 곡률 변화에 따른 기존 문헌 과의 비교를 통하여 본 연구결과를 검증하였다. 본 연구결과는 고유진동 특성에 영향을 미치는 탄소나노튜브 보강의 중요성을 보여준다.

Large space structures exhibit different natural vibration characteristics depending on the aspect ratio of structures such as half-open angle. In addition, since the actual large space structure is mostly supported by the lower structure, it is expected that the natural vibration characteristics of the upper structure and the entire structure will vary depending on the lower structure. Therefore, in this study, the natural vibration characteristics of the dome structure are analyzed according to the natural frequency ratio by controlling the stiffness of the substructure. As the natural frequency of the substructure increases, the natural frequency of the whole structure increases similarly to the natural frequency of the upper structure. Vertical vibration modes dominate at 30° and 45°, and horizontal vibration modes dominate at 60° and 90°.

Following the earthquake that shook the city of Gyeongju, Korea, in 2016, it became apparent that research on the safety of cultural heritages against the seismic hazards is necessary in Korea. Predictions of how historically significant stone pagodas would behave the earthquakes anticipated in near future, which are the subject of this study, is also required. In this study, the dynamic characteristics of 15 cultural heritage designated stone pagodas of Korea were investigated, including natural frequency and damping ratio, and the stiffness of the stone material and its contact area were determined using eigenvalue analysis by assuming the stone pagodas to be multi-degree-of-freedom structures. The results of this study enable the structural modeling of stone pagodas using a finite element analysis program and the method is expected to be useful in assessing the structural safety of stone pagodas against vertical loads as well as lateral forces, including earthquakes. Also, by identifying the dynamic characteristics of the structures, the results of this study can be utilized as a nondestructive testing method to determine the rigidity of cultural heritage structures and to identify inherent problems. The natural frequencies of the Korean stone pagodas were measured to be within 3.5~8.3㎐, excluding cases with distinct natural frequency results, and it was determined that the natural frequencies of the stone pagodas are influenced by various parameters including the height and joint stiffness of the structures.

Theories for composite structures are too difficult for design engineers for construction. The purpose of this paper is to demonstrate to the practicing engineers, how to apply the advanced composite materials theory to the structures. In this study, the natural frequency of a laminated cantilever beam was studied. An ultrasonic testing platform was employed to resonate the beam, and its time domain signal was optically measured. The natural frequency was quantified through the fast Fourier transform of the waveform, and the result showed good agreement with a theoretical estimation from the Euler-Bernoulli beam theory. This study is expected to provide a dynamic evaluation technique for laminated cantilever beam structures.

오늘날까지 적층 마이크로 외팔보의 고유진동수에 대하여 연구가 진행되었다. 마이크로 보는 실리콘 재질로 만들어 지지만, 그것의 상하 표면은 얇은 금 박막층(~30nm)이 증착되어 있다. 초음파 검사를 위해 초음파 테스트 플랫폼을 사용했으며, 시간영역 신호는 광학적으로 측정되었다. 고유진동수는 파형을 고속 Fourier 변환을 통해 정량화하였으며, 결과적으로 고전적인 보 이론과 일치하는 결과를 보여 주었다. 본 연구는 마이크로/나노스케일 재료와 마이크로 구조에 대한 동적평가기법 을 제공할 것으로 기대된다.

본 연구에서는 5층에 설치된 능동질량감쇠기를 사용하여 5층 철골구조물의 처음 세 개 모드의 모드 특성을 식별하였다. 이 건물은 병진모드와 비틀림모드의 고유진동수가 매우 근접하며, 이 경우 정확한 모드 분리와 모달 파라미터 식별은 매우 어렵다. 사인 하중 가진실험을 수행하여 모드 진동수, 감쇠비, 질량, 모드형상을 식별하였고, 근접한 모드 응답을 분리하였다. 식별된 시스템은 동일 한 입력신호를 사용하여 측정된 구조물의 응답과 매우 근접한 응답을 추정할 수 있다.

In this paper, the method of vibration analysis for calculating the natural frequency is presented. This method is a simple but exact method of calculating natural frequencies corresponding to the modes of vibration for the cantilevered composite materials conical beam. The influence of natural frequency of the cantilevered composite materials conical beam is presented. This method may be extended to stability analysis of complex structureal elements.

Theories of advanced composite structures are too difficult for such field engineers and some simple methods are necessary. In this paper, Simple method of vibration analysis is presented. This method presented in this paper is studied self-weight and other loads. The result of the 2~3 times iteration is good enough for field engineering purposes. In the case of cantilevered composite materials beams with different cross section, increase of mass near the support does not significantly affect the vibration characteristics. As a calculations of the simple method of vibration analysis for cantilevered composite materials beams with different cross section, it is noted that the result of the second cycle at the point of free end (actually 5L/6 span) is only 2.2% away from the ‘exact’ solution.

This study analyze the dynamic response property of latticed domes according to natural frequency ratio of substructure. Through eigenvalue analysis, it is was confirmed that the half-open angle 30° and 45° dominate vibration mode of the vertical direction and the half-open angle 60° and 90° dominate vibration mode of the horizontal direction. Through the dynamic response analysis, it is was confirmed that the first frequency about total structure largely appears about the vertical and the horizontal direction regardless of half-open angle.

Large spatial structures can not easily predict the dynamic behavior due to the lack of construction and design practices. The spatial structures are generally analyzed through the numerical simulation and experimental test in order to investigate the seismic response of large spatial structures. In the case of analysis for seismic response of large spatial structure, the many studies by the numerical analysis was carried out, researches by the shaking table test are very rare. In this study, a shaking table test of a small-scale arch structure was conducted and the dynamic characteristics of arch structure are analyzed. And the dynamic characteristics of arch structures are investigated according to the various column cross-section and length. It is found that the natural vibration periods of the small-scaled arch structure that have large column stiffness are very similar to the natural vibration period of the non-column arch structure. And in case of arch structure with large column stiffness, primary natural frequency period by numerical analysis is very similar to the primary natural frequency period of by shaking table test. These are because the dynamic characteristics of the roof structure are affected by the column stiffness of the spatial structure.

This study investigate the dynamic response changes of rib dome structure according to property changes of Substructure. Eigenvalue analysis is conducted in first natural frequency of rib dome versus substructure and searched in the dominant mode of horizontal and vertical direction. Resonance frequency by each first natural frequency of the rib dome structure, substructure and total structure is applied for a seismic wave. That is analyzed about maximum displacement response ratio and maximum acceleration response ratio.

In this paper. the effects of the aspect ratio on the natural frequency of the advanced composite road structures is studied. The advanced composite structures are too difficult for such design engineers for construction and some simple but accurate enough methods are necessary. Some laminate orientations have decreasing values of  ,  ,  and  stiffnesses as the ply number increases. The plate aspect ratio considered is from 1 to 5. Most of the road structures have large aspect ratios, for such cases further simplification is possible by neglecting the effect of the longitudinal moment terms.

Wind turbine tower has a very important role in wind turbine system as one of the renewable energy that has been attracting attention worldwide recently. Due to the growth of wind power market, advance and development of offshore wind system and getting huger capacity is inevitable. As a result, the vibration is generated at wind turbine tower by receiving constantly dynamic loads such as wind load and wave load. Among these dynamic loads, the mechanical load caused by the rotation of the blade is able to make relatively periodic load to the wind turbine tower. So natural frequency of the wind turbine tower should be designed to avoid the rotation frequency of the rotor according to the design criteria to avoid resonance. Currently research of the wind turbine tower, the precise research does not be carried out because of simplifying the structure of the other upper and lower. In this study, the effect of blade modeling differences are to be analyzed in natural frequency of wind turbine tower.

This paper examines the pounding problem between adjacent decks subjected to strong earthquakes. The elastomeric bearings in an isolated bridge reduce the stresses on the superstructure and cushion the impact by transferring smaller seismic forces to the substructure. On the other hand, these bearings also allow large horizontal displacement of the superstructure due to seismic forces. Bridges having various supporting soil conditions and different frequency ratios between adjacent decks are investigated by numerical analysis. In the analysis, decision making is conducted whether the collision took place or not and, the magnitude of pounding force and the duration time of collision are obtained and the results are discussed.

Natural frequency characteristic of Wind turbine tower is important for designing of tower due to guarantee of structural safety of tower. In GL specification, natural frequency of tower should be designed by consideration of blade rotational frequency. Natural frequency characteristic of tower could be changed by mass ratio of RNA-tower, modeling method of blade and angle of blade in idling condition. In this research, natural frequency of tower is analysed by ABAQUS and compared it result according to tower dimension.