노후 구조물의 동적 특성 평가를 위해 대표적인 접촉식 센서인 LVDT와 가속도계를 활용한다. 전통 적인 센서의 데이터 신뢰성은 높지만, 작동 원리로 인하여 대상 구조물의 물리적 접근과 센서의 설치 가 필요하다. 조밀한 센서 설치를 위해선 많은 수의 센서와 데이터 수집장치도 추가적으로 필요하다. 이런 단점을 보완하고자 비접촉식 센서의 개발이 활발히 진행 중이며, 특히 비전센서를 활용한 동적 변위 측정에 관한 연구 및 개발에 많은 진척이 있다. 비전센서를 활용한 동적 변위 측정 시스템은 내 적 파라미터 및 외적 환경조건에 따라 측정 정확도가 크게 변화한다. 주된 내적 파라미터로 영상장비 의 공간분해능은 이미지 센서의 물리적 크리와 촬영거리의 증가 혹은 관심영역이 작아짐에 따라 영향 을 많이 받는다. 외적 환경조건으로 저조도 환경에서 타겟의 밝기차이가 줄어들어 이미지 프로세싱 과 정에서 불리한 조건이며, 이는 동적 변위 측정 정확도 저하로 이어진다. 본 연구에서 저조도 환경에서 비전센서의 운용거리 한계를 초해상화를 적용하여 극복하고자 하며, 인공적 및 자연적 타겟에 대한 동 적 변위 측정 성능을 비교 분석하였다. 동적 변위 측정 실내 실험을 위해 저조도 조건에서 3층 전단 구조물을 9Hz로 가진하였다. 동시에 Sony사의 DSC-100M7 카메라를 활용하여 조화진동으로 인해 발생되는 각층의 변위를 FHD화질 120FPS로 촬영하였고 측정 정확도 비교 분석을 각층의 LVDT 측 정값으로 진행하였다. 촬영거리를 10m를 기준으로 10m씩 증가하면서 최대 40m까지 변위 값을 측정 하였으며, 공간분해능 증가를 위해 GAN기반 초해상화 모델인 RealSR을 적용시켰다. 초해상화를 활용 하여 동적변위를 측정한 결과 저조도 환경에서도 비전센서의 운용 거리가 증가함을 확인할 수 있었으 며, 동시에 변위 측정 정확도도 함께 상승하는 것을 보여줬다.

최근 국내 지진 발생 빈도 및 강도가 증가함에 따라 지진 발생시 건물 주요 구조부에 대해서는 내진설계 및 내진 구조기술이 적용되어 지진에 대비하고 있으나, 비구조 요소인 커튼월과 창호에 대해서는 내진에 대비한 충분한 고려가 이루어지지 못하고 있다. 본 연구에서는 동적 내진성능 기준을 만족할 수 있는 커튼월을 개발하기 위해 동적 지진파 인가 시 커튼월이 파손 없이 대응 가능한 지진 변위 대응 패스너를 적용하여 동적 내진성능실험을 통해 이를 규명하고자 한다. 동적 내진성능실험을 수행한 결과, 본 연구에서 제시한 3축 이동형 패스너를 활용한 커튼월이 실제 지진파에 대응 가능하다는 것을 확인할 수 있었다.

중·저층 구조물의 구조물 건전도 모니터링을 위해 아두이노 기반 가속도 센서를 적용하기 앞서 아두이노 기반의 저가형 가속도 센서의 진동 계측 성능을 확인하고, 그 한계를 명확히 하고자 한다. 가진 장치에 상용 가속도 센서와 저가형 가속도 센서를 설치 하고 다양한 Case의 Sin파를 가진하여 그 응답을 계측하였다. 응답 결과는 상용 가속도 센서를 기준으로 저가형 센서의 계측 정확성을 비교하였다. 가진 진동수 추정에 있어서 대부분의 Case에서 유사한 결과를 나타내었으나 Magnitude 추정 결과에 있어서 가진 진폭이 낮은 1Hz/100mm이하의 경우 Magnitude 추정값이 부정확하게 나타났다. 이후 모든 Case에서는 저가형 가속도 센서와 상용 가속도 센서의 Magnitude 추정 결과가 유사하게 나타났다. 이러한 실험 결과를 바탕으로 아두이노 기반 저가형 가속도센서는 대체적으로 동적 계측의 유효성이 있다고 판단된다.

This study evaluates safety assessment before and after repair of Seonamsa temple seungseon bridge, which refer to the representative Hongye bridge in Korea. In this approach natural frequency of the structure were considered in the modeling procedure. Trial & error method is applied to obtain the approximate natural frequency before and after retrofit construction. Stiffness of the actual structure was examined to account for the dynamic characteristics of Hongye bridge measured in the field and adjusting parameters in computer modeling. The safety and usability of the stone structure in terms of load bearing capacity and displacement were examined.

본 연구는 간편화된 소성 접선 곡선을 적용하여 노측용 가드레일 시스템의 충격 성능을 평가하기 위한 유한요소 충돌해석을 수행하였다. 충돌해석은 Cowper-Symond 모델을 적용하여 변형률 속도 영향에 대한 결과의 정확성을 향상시켰다. 수치 해석 결과는 소성 접선 곡선을 고려한 향상된 모델의 중요성을 보여준다. 다양한 매개변수에 대한 해석 결과는 서로 다른 모델에 대하여 동적 응답 및 탑승자 안전지수를 중심으로 비교 검증하여 도출하였다.

In order for the probe to perform ocean exploration and survey research, it is necessary to adjust the position of the ship as desired by dynamic positioning system. The dynamic positioning system of T/S NARA is applied to K-POS dynamic positioning system of Kongsberg, which makes maintaining the ship's position, changing position and heading control possible. T/S NARA is not capable of dynamic positioning if one or more propulsive forces are lost with DP Level One. However, it is predicted that dynamic positioning can be achieved even at the time of missing one thrust in a good sea condition. Therefore, we want to analyze the effect of each propulsion on the performance of dynamic position system. When one of the bow thruster and azimuth thrusters lost their propulsion, maintaining the ship's position, changing position and heading control performance were compared and analyzed. If the situation occurred disable from using the bow thruster, they can not maintain ship's position. Azimuth thruster was influential for the ship's position control and bow thruster was influential in heading control. The excellent dynamic positioning performance can be achieved, considering the propulsion power that will have a impact on each situation in the future.

Piloti-type building is one of typical vertical atypical buildings. These buildings can fail by weak-story or flexible-story mechanism on the first story. They should be designed by taking into account the special seismic load, but those less than six stories are not required to confirm the seismic performance from structural engineers in Korea. For this reason, small-size pilloti-type RC buildings need to be checked for seismic performance. Based on this background, this study performed nonlinear dynamic analysis using the PERFORM-3D for small-size pilloti-type RC buildings and assessed their seismic performance. Examples are two through four story buildings with and without walls in the first story. The walls and columns in the first story satisfied the target performance in the basic of flexural behavior due to quite a large size and reinforcement. However, wall shear demands exceed shear strength in some buildings. When designed for KBC2009, wall shear strength exceed shear demand in some buildings, but still does not in others. Consequently, wall shear must be carefully checked in both existing and new small-size pilloti-type RC buildings.

본 논문에서는 전통 목조건축물로 되어 있는 대한민국의 국보 1호인 숭례문의 구조해석을 수행하고 안전도를 평가하였다. 전통 목조건축의 대부분의 하중을 차지하고 있는 숭례문의 지붕하중을 상세히 산정하고 숭례문의 가구구성 특징을 면밀히 살펴 범용 구조해석 소프트웨어인 midas Gen으로 구조해석모델을 구축하였다. 수직하중에 대한 정적구조해석을 수행하고 주요 수직 수평 구조부재의 안전성과 주요 수평부재의 사용성을 평가하였다. 숭례문의 동적거동특성을 평가하기 위하여 현장에서의 충격해머실험과 구조해석 소프트웨어를 이용한 고유치해석을 수행하고 그 결과를 비교하고 주요모드를 도출하였다. 수직하중에 대한 검토결과 숭례문은 구조적 능력에 여유가 있는 것으로 나타났다.

This study investigated the embedded depth of guardrail posts through 3-D soil material model and carried out evaluation of the dynamic performance of guard rail. In order to calculate for embedded depth of sloping ground, displacement of guardrail posts is analyzed according to the embedded depth of experiment variables. Through the static test of guardrail posts, the maximum deflection was found to decrease the interval. By performing the dynamic test using the Bogie Car, that is confirmed the elastic modulus of the soil occuring the maximum deflection. Guardrail posts is considered to need for further reinforcement in the larger slope than the plains. This study researched about maximum displacement and deviation velocity through dynamic performance of guardrail system and conducted analysis about protection performance evaluation of passenger.

PURPOSES: A tack coat has been utilized to increase the bond performance between the surface layer and base course (intermediate course) at various road pavement sites. This is similarly true in other nations. Based on this connection, the objective of the present study is to evaluate the properties of hot mix asphalt (HMA) mixtures with an RSC-4 or BD-Coat and determine the application rate of the tack coat. METHODS: The HMA specimens were manufactured using superpave gyratory compaction. The HMA mixtures were composed of a 5-cm thick surface layer and a 10-cm thick base course. An impact hammer resonance test (IHRT) and a static load shear test were conducted to evaluate the performance of the HMA mixtures with a tack coat. From these tests, the dynamic moduli related to the high-frequency resistance and interlayer shear strength (ISS) of HMA could be obtained. RESULTS: The results of the dynamic moduli of HMA are discussed based on the resonance frequency (RF). To check the accuracy of the IHRT, we conducted a coherence analysis. A direct shear test using the application of a static load test was carried out to evaluate the interlayer shear strength (ISS) of HMA. CONCLUSIONS: The maximum ISS was demonstrated at an RSC-4 application rate of 462 gsm, and the maximum dynamic modulus was demonstrated at an RSC-4 application rate of 306 gsm. By averaging the results of the ISS, the maximum ISS values were obtained when a BD-Coat application rate of 602 gsm was applied.

PURPOSES: This paper evaluates, using LS/DYNA-3D software, the vehicle impact performance of flexible barriers made of steel WBeam supported by four different types of post configurations. These types include circular post, H-shape post, C-shape post, and square post. METHODS : The post-soil interaction has been investigated according to different impact angles. For this purpose, energy absorption, maximum displacements of post and rail, and occupant risk index of THIV have been compared each other. The three dimensional soil material model, instead of the conventional spring model based on Winkler and p-y curve, has been used to increase the correctness of computational model. RESULTS: It is noted the crash energy absorption has been increased with respect to the increase of impact angle. CONCLUSIONS : In particular, a post with open section(H-shape, C-shape) shows the greater crash energy absorption capability as compared with a post with closed section under the same level of impact conditions.

Recently, environmental problems associated with the excessive use of fossil fuel are hot issue throughout the world. As an alternative energy resource, the importance of renewable energy is continuously rising. Especially, growth rate of photovoltaic energy generation is one of the best. In this paper, floating PV generation system made of pultruded fiber reinforced polymeric plastic (PFRP) is discussed. It is well known that PFRP has many advantages such as high corrosion resistance, high specific strength/stiffness, etc. Compared with conventional construction materials. To investigate the structural behavior under flow induced dynamic loading, members and connections of members are tested under cyclic loading. It was found that the structural system is strong enough to resist such a cyclic loading.

This paper will argue that tire damping can be critical to modelling of vehicle dynamic. Tire damping is usually skipped in the process of vehicle modelling. There are two reasons for this. The first one is the simplification of the computer simulation. The second is that the effect of tire damping is thought insignificant to vehicle dynamics. But there is support for skipping tire damping. In this paper, the vehicle performances are investigated with and without tire damping force applied in the dynamic modelling of the system. The transient responses in the time domain and the frequence responses in the frequence domain are analysed to see the effects of tire damping qualitatively and quantitatively. It is shown that significant errors can occur when the tire damping force is skipped during the simulation process.

PURPOSES: This paper evaluates, using LS/DYNA-3D software, the vehicle impact performance of flexible barriers made of steel WBeam supported by four different types of post configurations. These types include circular post, H-shape post, C-shape post, and square post. METHODS : The post-soil interaction has been investigated according to different impact angles. For this purpose, energy absorption, maximum displacements of post and rail, and occupant risk index of THIV have been compared each other. The three dimensional soil material model, instead of the conventional spring model based on Winkler and p-y curve, has been used to increase the correctness of computational model. RESULTS: It is noted the crash energy absorption has been increased with respect to the increase of impact angle. CONCLUSIONS : In particular, a post with open section(H-shape, C-shape) shows the greater crash energy absorption capability as compared with a post with closed section under the same level of impact conditions.

국내 철골모멘트골조를 이전 KBC2005 및 현 KBC2009 기준에 따라 설계한 후 비선형동적해석을 이용하여 FEMA355F의 내진성능평가 절차에 따라 성능을 평가하였다. 그 결과 비선형정적 Push-over 해석을 이용한 역량스펙트럼법과 차이가 있었다. 특히국내 철골모멘트골조는 약패널존을 가지기 때문에 비선형동적해석을 통해서만 보다 정확한 거동을 예측할 수 있었다. 국내 철골모멘트골조는 지반 조건 SB　또는 SC에 위치한다면 층수 및 R값에 관계없이 성능목표를 만족하는 것으로 나타났다. 하지만 지반 조건 SD　또는SE에 위치한다면 성능목표 만족 여부는 명확하지 않았다. 따라서 KBC2005나 KBC2009 어떤 기준을 사용하더라도 지반 조건이 상대적으로 좋다면 국내 철골모멘트골조는 내진성능을 충분히 확보하고 있다고 볼 수 있다.

PURPOSES : In This study two different concrete barrier systems have been proposed to be established at the small vehicle driveway. One is for median barrier, and the other is for roadside barrier. METHODS : In order to determine the suitable shape of barrier, the impact parameters including vehicle weight, impact angle, impact velocity and impact level have been analyzed. The real crash test has been carried out with 0.9 ton and 2.5 ton vehicles, respectively by using the 2m segment type concrete barriers connected by steel plates that are totally 40m barrier systems. RESULTS : The numerical results obtained by LS/DYNA-3D software are compared with real crash tests from the viewpoints of vehicle stability, vehicle trajectory, occupant risk, etc. CONCLUSIONS : From the above results, the dynamic performance of proposed barrier systems satisfies the specification of Korean Code for roadside safety structures.