In this study, the effects of operating conditions on the formation of reversible and irreversible fouling were investigated in the filtration using ceramic membrane for water treatment process. The effect of coagulation pretreatment on fouling formation was also evaluated by comparing the performance of membrane filtration both with and without addition of coagulant. A resistance-in-series-model was applied for the analysis of membrane fouling. Total resistance (RT) and internal fouling resistance (Rf) increased in the membrane filtration process without coagulation as membrane flux and feed water concentrations increased. Internal fouling resistance, which was not recovered by physical cleaning, was more than 70% of the total resistance at the range of the membrane flux more than 5 m3/m2･day. In the combined process with coagulation, the cake layer resistance (Rc) increased to about 30-80% of total resistance. As the cake layer formed by coagulation floc was easily removed by physical cleaning, the recovery rate by physical cleaning was 54~90%. It was confirmed from the results that the combined process was more efficient to recover the filtration performance by physical cleaning due to higher formation ratio of reversible fouling, resulted in the mitigation of the frequency of chemical cleaning.

In water treatment process using microfiltration membranes, manganese is a substance that causes inorganic membrane fouling. As a result of analysis on the operation data taken from I WTP(Water Treatment Plant), it was confirmed that the increase of TMP was very severe during the period of manganese inflow. The membrane fouling fastened the increase of TMP and shortened the service time of filtration or the cleaning cycle. The TMP of the membrane increased to the maximum of 2.13 kgf/cm2, but it was recovered to the initial level (0.17 kgf/cm2) by the 1st acid cleaning step. It was obvious that the main membrane fouling contaminants are due to inorganic substances. As a result of the analysis on the chemical waste, the concentrations of aluminum(146-164 mg/L) and manganese(110-126 mg/L) were very high. It is considered that aluminum was due to the residual unreacted during coagulation step as a pretreatment process. And manganese is thought to be due to the adsorption on the membrane surface as an adsorbate in feed water component during filtration step. For the efficient maintenance of the membrane filtration facilities, optimization of chemical concentration and CIP conditions is very important when finding the abnormal level of influent including foulants such as manganese.

최근 막여과 정수처리에 대한 관심이 높아지고 있으나, 공정설계를 위한 소프트웨어가 널리 보급되어 있지 않아서 현장적용의 어려움이 발생하고 있다. 본 연구에서는 막여과 정수처리 공정설계를 지원할 수 있는 프로그램과 설계기법을 개발하고자 하였다.

수온 상승에 따른 조류 등 이취미 물질의 증가, 미량 유해물질의 검출로 인해 기존 여과 공정으로 시민들의 수질 기대조건을 충족할 수 없기 때문에 오존+활 성탄 등의 고도정수처리 공정의 도입이 활성화되었으며, 이미 대도시, 광역단위 에는 고도정수처리 공정 도입이 완료된 상황이다. 대부분의 국내 정수장의 여과 공정은 급속 모래여과 공정으로 구성되어 있으며, 10년간 막여과 공정이 등장하여 여과 공정에 따른 후단 오존+활성탄 공정에 미치는 영향을 파악하는 것이 필요하다고 판단되었다. 서울시 Y 정수장에 설치된 고도정수처리 파일럿 플랜트 를 활용하여 고도정수처리 공정에 모래여과수와 막여과수가 유입되었을 경우 수질 및 제거율의 변화와 활성탄 표면 변화를 관찰하였고 이를 통해 막여과 정수처리 공정 도입 필요성을 검토하였다.

Temperature correction trans-membrane pressure (TC-TMP) is frequently used as a fouling index in membrane water treatment plants. TC-TMP equation is derived based on an assumption that the total membrane resistance (i.e. the sum of the intrinsic membrane resistance and fouling resistance) is not affected by temperature. This work verified the validity of this assumption using microfiltration (MF) and ultrafiltration (UF) membranes with and without fouling. The foulants used in the work were kaolin (inorganic) and humic acid (organic). The intrinsic resistances of MF and UF membranes remains at constant values regardless of temperature change. When the same amount of foulants were accumulated on the membrane, inorganic fouling resistance with kaolin was constant regardless of temperature change while organic fouling resistance with humic acid decreased at higher temperatures, which means that TC-TMP cannot be used as a fouling index when organic fouling occurs in a real field application. Since TC-TMP underestimates the amount of fouling at higher temperatures, more attention should be necessary in the operation of membrane water treatment plant in a hotter season like summer.

Various treatment system for residuals have applied to save water resources, but most of them were not be satisfied with legal standard consistently. In this study, submerged membrane treatment system was operated to treat water treatment plant residuals and operation parameters was evaluated. Result of this experiment, high concentration organic matters contributed to high increase Transmembrane pressure(TMP) of membrane system(from 0.05 bar to 0.35 bar). And backwash process was effective to stabilize membrane system operation. After Cleaning-In-Place(CIP), permeability was recovered about 100 % from first operation condition. Inorganic matters (Fe, Mn, Al, Ca, Mg) were not effective membrane filtration performance. The quality of residual treatment was satisfied with drinking water quality standard and a treated water from that system was suitable for water reuse.

섬진강 수계의 복류수를 대상으로 막여과 정수처리 공정 현장 적용성 평가를 위해 여과막의 공경에 따른 막오염도 예측 및 최적 응집제 주입농도 선정을 통해 파일롯플랜트 규모의 검증실험을 실시하였다. 막공경에 따른 막오염도 평가를 위한 여과저항 평가실험 결과, 0.1mum 와 0.01mum 여과막의 비가역적 여과저항 증가율은 각각 0.44×10 12/m2, 0.42×10 12/m2로 나타났으며, Flux-test 실험결과, 적정응집제 주입농도는 Jar-Test 실험결과에 비해 낮게 나타났다. 현장 적용성 평가를 위해 6개월 동안의 파일롯플랜트 운영을 수행하였다. 응집을 실시하지 않은 막여과공정은 여과유속 1.0~1.5m3/m2 day,응집을 실시한 막여과 공정은 여과유속 1.0~2.0m3/m2 day의 조건에서 운전한 결과 두 조건 모두 6개월 이상 막차압이 안정되게 유지되었다. 따라서 섬진강 수계의 복류수를 이용한 막여과 공정 운영에 있어 적정 여과유속으로 운전 시 응집제 사용 없이 안정적인 운전이 가능함을 알 수 있었다.

현재 막여과 공정은 정수처리에서 많은 관심을 받고 있다. 그러나 막여과 공정은 저압 운전이 가능한 정밀/한외여과 분리막을 이용할 때는 효과적인 용존성 유기물 제거가 이루어지지 않으며 막오염 현상으로 분리막의 투과도 감소가 일어난다. 고압 분리막을 이용할 경우 양질의 수질은 얻을 수 있으나 고압 운전으로 인하여 운전비용의 소모가 높다. 따라서 최근 분리막의 효율적인 정수처리 적용과 성능 향상을 위해서 다른 물리화학적 공정과 결합한 혼성공정에 대한 다양한 접근이 이루어지고 있다. 본 연구에서는 혼성공정으로 응집, 흡착, 특정 화학반응, 막표면 코팅 등과 정밀/한외여과 공정을 결합한 경우의 특징, 처리효율, 고려사항 등을 고찰하였다.