Tin-antimony sulfide nanocomposites were prepared via hydrothermal synthesis and a N2 reduction process for use as a negative electrode in a sodium ion battery. The electrochemical energy storage performance of the battery was analyzed according to the tin-antimony composition. The optimized sulfides exhibited superior charge/discharge capacity (770 mAh g-1 at a current density of 100 mA g-1) and stable lifespan characteristics (71.2 % after 200 cycles at a current density of 500 mA g-1). It exhibited a reversible characteristic, continuously participating in the charge-discharge process. The improved electrochemical energy storage performance and cycle stability was attributed to the small particle size, by controlling the composition of the tin-antimony sulfide. By optimizing the tin-antimony ratio during the synthesis process, it did not deviate from the solubility limit. Graphene oxide also acts to suppress volume expansion during reversible electrochemical reaction. Based on these results, tin-antimony sulfide is considered a promising anode material for a sodium ion battery used as a medium-to-large energy storage source.

One-dimensional (1D) piezoelectric nanostructures are attractive candidates for energy generation because of their excellent piezoelectric properties attributed to their high aspect ratios and large surface areas. Vertically grown BaTiO3 nanotube (NT) arrays on conducting substrates are intensively studied because they can be easily synthesized with excellent uniformity and anisotropic orientation. In this study, we demonstrate the synthesis of 1D BaTiO3 NT arrays on a conductive Ti substrate by electrochemical anodization and sequential hydrothermal reactions. Subsequently, we explore the effect of hydrothermal reaction conditions on the piezoelectric energy conversion efficiency of the BaTiO3 NT arrays. Vertically aligned TiO2 NT arrays, which act as the initial template, are converted into BaTiO3 NT arrays using hydrothermal reaction with various concentrations of the Ba source and reaction times. To validate the electrical output performance of the BaTiO3 NT arrays, we measure the electricity generated from each NT array packaged with a conductive metal foil and epoxy under mechanical pushings. The generated output voltage signals from the BaTiO3 NT arrays increase with increasing concentration of the Ba source and reaction time. These results provide a new strategy for fabricating advanced 1D piezoelectric nanostructures by demonstrating the correlation between hydrothermal reaction conditions and piezoelectric output performance.

Magnesium hydroxide sulfate hydrate (MHSH) whiskers were synthesized via a hydrothermal reaction by using MgO as the reactant as well as the acid solution. The effects of the H2SO4 amount and reaction time at the same temperature were studied. In general, MHSH whiskers were prepared using MgSO4 in aqueous ammonia. In this work, to reduce the formation of impurities and increase the purity of MHSH, we employed a synthesis technique that did not require the addition of a basic solution. Furthermore, the pH value, which was controlled by the H2SO4 amount, acted as an important factor for the formation of high-purity MHSH. MgO was used as the raw material because it easily reacts in water and forms Mg+ and MgOH+ ions that bind with SO4 2- ions to produce MHSH. Their morphologies and structures were determined using X-ray diffraction (XRD) and scanning electron microscopy (SEM).

MoO3 metal oxide nanostructure was formed by hydrothermal synthesis, and a perovskite solar cell with an MoO3 hole transfer layer was fabricated and evaluated. The characteristics of the MoO3 thin film were analyzed according to the change of hydrothermal synthesis temperature in the range of 100 ℃ to 200 ℃ and mass ratio of AMT : nitric acid of 1 : 3 ~ 15 wt%. The influence on the photoelectric conversion efficiency of the solar cell was evaluated. Nanorod-shaped MoO3 thin films were formed in the temperature range of 150 ℃ to 200 ℃, and the chemical bonding and crystal structure of the thin films were analyzed. As the amount of nitric acid added increased, the thickness of the thin film decreased. As the thickness of the hole transfer layer decreased, the photoelectric conversion efficiency of the perovskite solar cell improved. The maximum photoelectric conversion efficiency of the perovskite solar cell having an MoO3 thin film was 4.69 % when the conditions of hydrothermal synthesis were 150 ℃ and mass ratio of AMT : nitric acid of 1 : 12 wt%.

Iron oxides currently attract considerable attention due to their potential applications in the fields of lithiumion batteries, bio-medical sensors, and hyperthermia therapy materials. Magnetite (Fe3O4) is a particularly interesting research target due to its low cost, good biocompatibility, outstanding stability in physiological conditions. Hydrothermal synthesis is one of several liquid-phase synthesis methods with water or an aqueous solution under high pressure and high temperature. This paper reports the growth of magnetic Fe3O4 particles from iron powder (spherical, <10 μm) through an alkaline hydrothermal process under the following conditions: (1) Different KOH molar concentrations and (2) different synthesis time for each KOH molar concentrations. The optimal condition for the synthesis of Fe3O4 using Fe powders is hydrothermal oxidation with 6.25 M KOH for 48 h, resulting in 89.2 emu/g of saturation magnetization at room temperature. The structure and morphologies of the synthesized particles are characterized by X-ray diffraction (XRD, 2θ = 20°–80°) with Cu-kα radiation and field emission scanning electron microscopy (FE-SEM), respectively. The magnetic properties of magnetite samples are investigated using a vibrating sample magnetometer (VSM). The role of KOH in the formation of magnetite octahedron is observed.

본 연구는 1M Li2SO4 및 1M Na2SO4 수용액에서 CoSe 나노 입자의 전기 화학적 성능을 조사 하였다. CoSe 나노 입자의 전기 화학적 효율은 1M Na2SO4 전해질에서 더 높은 비정전 용량을 보여주는 결 과를 얻었고 이것은 주로 1M Na2SO4 용액의 벌크 전해질에서 수화 된 이온의 빠른 이동과 활물질에 의해 제공되는 낮은 전기 화학적 임피던스가 원인이라 사료된다. 또한, 순환 전압 전류법 안정성 실험에서 25 mV s-1의 스캔 속도로 1000 회 연속 순환 전압 전류 측정주기 후에도 각각 1M Na2SO4 및 1M Li2SO4에서 약 92 % 및 89 %의 특정 정전 용량의 유지를 보여주었다. 이 연구는 새로운 하이브리드 슈퍼 커패시터를 개발하기 위한 기초 데이터를 제공하며 비대칭 슈퍼 커패시터의 양극으로 사용될 수 있음을 시사한다.

In the present work, we synthesize nano-sized ZnO, SnO2, and TiO2 powders by hydrothermal reaction using metal chlorides. We also examine the energy-storage characteristics of the resulting materials to evaluate the potential application of these powders to dye-sensitized solar cells. The control of processing parameters such as pressure, temperature, and the concentration of aqueous solution results in the formation of a variety of powder morphologies with different sizes. Nano-rod, nano-flower, and spherical powders are easily formed with the present method. Heat treatment after the hydrothermal reaction usually increases the size of the powder. At temperatures above 1000oC, a complete collapse of the shape occurs. With regard to the capacity of DSSC materials, the hydrothermally synthesized TiO2 results in the highest current density of 9.1 mA/cm² among the examined oxides. This is attributed to the fine particle size and morphology with large specific surface area.

Transition-metal oxide semiconductors have various band gaps. Therefore, many studies have been conducted in various application fields. Among these, methods for the adsorption of organic dyes and utilization of photocatalytic properties have been developed using various metal oxides. In this study, the adsorption and photocatalytic effects of WO3 nanomaterials prepared by hydrothermal synthesis are investigated, with citric acid added in the hydrothermal process as a structure-directing agent. The nanostructures of WO3 are studied using transmission electron microscopy and scanning electron microscopy images. The crystal structure is investigated using X-ray diffraction patterns, and the changes in the dye concentrations adsorbed on WO3 nanorods are measured with a UV-visible absorption spectrophotometer based on Beer-Lambert’s law. The methylene blue (MB) dye solution is subjected to acid or base conditions to monitor the change in the maximum adsorption amount in relation to the pH. The maximum adsorption capacity is observed at pH 3. In addition to the dye adsorption, UV irradiation is carried out to investigate the decomposition of the MB dye as a result of photocatalytic effects. Significant photocatalytic properties are observed and compared with the adsorption effects for dye removal.

Nano-sized Zinc selenide (ZnSe) powder was successfully synthesized using Zn and Se precursors in a hydrothermal process. Temperature for the synthesis was varied from 95 oC to 180 oC to evaluate its influence on the microstructural properties of the synthetic particles. ZnSe powder thus fabricated was characterized using various analytical tools such as SEM, XRD, TEM and UV-Vis methods. Two types of ZnSe particles, that is, the precipitated particle and the colloidal particles, were identified in the analysis. The precipitated particles were around 100 nm in average size, whereas the average size of the colloidal particles was around 20 nm. The precipitated particles made at 150 oC and 180 oC were found to be a single phase of ZnSe; however, an inhomogeneous phase was obtained at the lower synthesis temperature of 95 oC, suggesting that the temperature for the synthesis should be over 100 oC. The precipitated particles were inactive in the UV-Vis absorption investigation, whereas the colloidal particles showed that absorptions occurred at 380 nm in the UV-Vis spectrum.

금속산화물 반도체 중 하나인 산화아연은 인체에 무해하고 친환경적이며, 우수한 화학적, 열 적 안정성의 특성을 지니며 3.37 eV의 넓은 밴드갭 에너지와 60 meV의 높은 엑시톤 바인딩 에너지로 인해 태양전지, 염료페기물의 분해, 가스센서 등 다양한 분야에 응용이 가능한 물질이다. 산화아연은 입 자 형상 및 결정성의 변화에 따라 광촉매 활성이 변하게 된다. 따라서, 다양한 실험변수와 첨가제를 사 용하여 입자를 합성하는 것이 매우 중요하다. 본 논문에서는 마이크로파 수열합성법을 사용하여 산화아연을 합성하였다. 전구체로는 질산아연을 사 용하였고, 수산화나트륨을 사용하여 용액의 pH를 11로 조정하였다. 첨가제로는 계면활성제인 에탄올아 민, 세틸트리메틸암모늄브로마이드, 소듐도데실설페이트, 솔비탄모노올레이트를 첨가하였다. 합성된 입자 는 별모양, 원추형, 씨드형태, 박막형태의 구형의 형상을 보였다. 합성된 산화아연의 물리・화학적 특성 은 XRD, SEM, TGA을 통하여 확인하였고, 광학적 특성은 UV-vis spectroscopy, PL spectroscopy, Raman spectroscopy으로 확인하였다.

본 연구에서는 고순도의 모데나이트(Mordenite) 입자를 합성하기 위하여 천연 제올라이트를 시드로 사용하여 시 드의 농도 및 수열합성 시간에 따른 천연 제올라이트 시드가 합성에 미치는 영향을 고찰하였다. 그 결과 시드가 입자의 형성 에 큰 영향을 끼치는 것을 확인할 수 있었고 시드를 3 g/100 g batch 주입하여 140°C에서 72시간 동안 수열합성을 진행하였 을 때 1-2 μm 사이즈의 고순도 모데나이트 입자를 합성할 수 있었다. 이를 통해 모데나이트 입자의 성장 기구를 규명할 수 있었으며, 모데나이트 입자 형성에 있어 시드는 첫째, 구형 모데나이트 전구체 형성 자리 공급의 역할과, 둘째 모데나이트 원 료 물질 소스 역할을 한다는 것을 알 수 있었다. 합성된 모데나이트 입자의 가스 흡착량 분석 결과 CO2 기체의 흡착량이 97.19 mg/g로 다른 가스들에 비해 비교적 높은 흡착성능을 보였으며, CO2/H2의 선택도가 가장 우수한 것으로 나타났다. 따라 서 이러한 결과들을 바탕으로 용도에 맞는 고순도 상의 모데나이트 입자를 합성할 수 있음을 확인하였고 보다 낮은 가격으로 우수한 분리성능을 갖는 분리막 소재개발에 활용할 수 있을 것이라 판단된다.

We report on an all-solution-processed hydrothermal method to control the morphology of ZnO nanostructures on Si substrates from three-dimensional hemispherical structures to two-dimensional thin film layers, by controlling the seed layer and the molar contents of surfactants during their primary growth. The size and the density of the seed layer, which is composed of ZnO nanodots, change with variation in the solute concentration. The ZnO nanodots act as heterogeneous nucleation sites for the main ZnO nanostructures. When the seed layer concentration is increased, the ZnO nanostructures change from a hemispherical shape to a thin film structure, formed by densely packed ZnO hemispheres. In addition, the morphology of the ZnO layer is systematically controlled by using trisodium citrate, which acts as a surfactant to enhance the lateral growth of ZnO crystals rather than a preferential one-dimensional growth along the c-direction. X-ray diffraction and energy dispersive X-ray spectroscopy results reveal that the ZnO structure is wurtzite and did not incorporate any impurities from the surfactants used in this study.

Flower-like nickel oxide (NiO) catalysts were coated on NiCrAl alloy foam using a hydrothermal method. The structural, morphological, and chemical bonding properties of the NiO catalysts coated on the NiCrAl alloy foam were investigated by field-emission scanning electron microscopy, scanning electron microscopy-energy dispersive spectroscopy, Xray diffraction, and X-ray photoelectron spectroscopy, respectively. To obtain flower-like morphology of NiO catalysts on the NiCrAl alloy foam, we prepared three different levels of pH of the hydrothermal solution: pH-7.0, pH-10.0, and pH-11.5. The NiO morphology of the pH-7.0 and pH-10.0 samples exhibited a large size plate owing to the slow reaction of the hydroxide (OH−) and nickel ions (Ni+) in lower pH than pH-11.5. Flower-like NiO catalysts (~4.7 μm-6.6 μm) were formed owing to the fast reaction of OH− and Ni2+ by increased OH− concentration at high pH. Thus, the flower-like morphology of NiO catalysts on NiCrAl alloy foam depends strongly on the pH of the hydrothermal solution.

본 연구에서는 고순도의 모데나이트 입자를 합성하기 위하여 천연 제올라이트를 시드로 사용하여 시드 농도 및 수열합성 시간에 따라 시드가 미치는 영향 을 고찰하였다. 시드를 3 g/100g batch 주입하여 140°C에서 72시간 동안 수열 합성 하였을 때 1-2 μm 사이즈의 고순도 모데나이트 입자를 안정적으로 합성할 수 있었다. 이를 통해 천연 제올라이트 시드는 모데나이트 입자의 성장에서 구형 모데나이트 전구체 형성 자리를 공급하고 모데나이트 원료 물질 소스 역 할을 한다는 것을 알 수 있었다. 이러한 결과들을 바탕으로 용도에 맞는 고순도 의 모데나이트 입자를 합성할 수 있음을 확인하였고 천연제올라이트를 사용함으로써 낮은 가격으로 우수한 성능을 갖는 소재개발에 활용할 수 있을 것이라 판단된다.

We report on the successful fabrication of ZnO nanorod (NR)/polystyrene (PS) nanosphere hybrid nanostructure by combining drop coating and hydrothermal methods. Especially, by adopting an atomic layer deposition method for seed layer formation, very uniform ZnO NR structure is grown on the complicated PS surfaces. By using zinc nitrate hexahydrate [Zn(NO3)2 ·6H2O] and hexamine [(CH2)6N4] as sources for Zn and O in hydrothermal process, hexagonal shaped single crystal ZnO NRs are synthesized without dissolution of PS in hydrothermal solution. X-ray diffraction results show that the ZnO NRs are grown along c-axis with single crystalline structure and there is no trace of impurities or unintentionally formed intermetallic compounds. Photoluminescence spectrum measured at room temperature for the ZnO NRs on flat Si and PS show typical two emission bands, which are corresponding to the band-edge and deep level emissions in ZnO crystal. Based on these structural and optical investigations, we confirm that the ZnO NRs can be grown well even on the complicated PS surface morphology to form the chestnut-shaped hybrid nanostructures for the energy generation and storage applications

In this work, uniform and nanosize(75nm) silicalite-1 crystals was hydrothermally synthesized by using 9TPAOH:0.16NaOH:25Si:495H2O solution at 80 ℃. They were applied as seed in the secondary growth process for preparing silicalite-1 membrane by template-free method. The highest ethanol/water separation factor of 119 with flux 0.58kg/m². Furthermore, these membranes (nano seed, template free silicalite-1 membrane) exhibit high permselectivity of He over SF6(123), and small gas permeation mechanism and Knudsen diffusion studies suggest that the membranes contain negligible intercrystalline or non-zeolite pores.

Porous metallic glass compact (PMGC) are developed by electro-discharge sintering (EDS) process of gas atomized Zr41.2Ti13.8Cu12.5Ni10Be22.5 metallic glass powder under of 0.2 kJ generated by a 450 μF capacitor being charged to 0.94 kV. Functional iron-oxides are formed and growth on the surface of PMGCs via hydrothermal synthesis. It is carried out at 150oC for 48hr with distilled water of 100 mL containing Fe ions of 0.18 g/L. Consequently, two types of iron oxides with different morphology which are disc-shaped Fe2O3 and needle-shaped Fe3O4 are successfully formed on the surface of the PMGCs. This finding suggests that PMGC witih hydrothermal technique can be attractive for the practical technology as a new area of structural and functional materials. And they provide a promising road map for using the metallic glasses as a potential functional application.

석탄회를 NaOH로 용융시킨 후 수열 처리에 의하여 제올라이트 A를 합성하였다. NaOH/석탄회의 비, 용융 온도, NaAlO2의 첨가량, 수열 처리 온도 및 시간이 생성된 제올라이트의 종류와 결정도에 미치는 영향에 대하여 연구하였다. 결정도가 높은 제올라이트의 생성에 필요한 최적의 NaOH/석탄회의 중량비는 1.2, 최적의 용융 온도는 550℃이었다. 용융된 석탄회로부터 Si4+ 와 Al3+의 용출은 교반 시간의 영향을 받지 않았다. 생성된 제올라이트의 형태는 첨가한 NaAlO2의 영향을 받는 것으로 나타났다. 적은 양의 NaAlO2를 첨가하면 제올라이트 X가 생성되나 NaAlO2의 양이 증가하면 단일상의 제올라이트 A가 생성되었다. 수열처리 시간과 온도가 증가하면 제올라이트 A는 hydroxysodalite로 변화하였다. 승온 속도를 낮춰 반응 온도까지의 도달시간을 증가시키면 결정도가 좋은 제올라이트 A를 얻을 수 있었다.

In this work, uniform and nanosize(75nm) silicalite-1 crystals was hydrothermally synthesized by using 9TPAOH:0.16NaOH:25Si:495H2O solution at 80 ℃. They were applied as seed in the secondary growth process for preparing silicalite-1 membrane by template-free method. And silicalite-1 membrane, which was coated by nano-size seed, showed a high EtOH/H2O separation factor of 128. The high separation factor could be explained by the role of nanosize seed. The application of nanosize seed successfully retarded the formation of interfacial voids between silicalite-1 grains. Therefore, it could be concluded that template-free hydrothermal process can produce silicalite-1 membrane with well performance.

We report the nitrogen monoxide (NO) gas sensing properties of p-type CuO-nanorod-based gas sensors. We synthesized the p-type CuO nanorods with breadth of about 30 nm and length of about 330 nm by a hydrothermal method using an as-deposited CuO seed layer prepared on a Si/SiO2 substrate by the sputtering method. We fabricated polycrystalline CuO nanorod arrays at 80˚C under the hydrothermal condition of 1:1 morality ratio between copper nitrate trihydrate [Cu(NO2)2·3H2O] and hexamethylenetetramine (C6H12N4). Structural characterizations revealed that we prepared the pure CuO nanorod array of a monoclinic crystalline structure without any obvious formation of secondary phase. It was found from the gas sensing measurements that the p-type CuO nanorod gas sensors exhibited a maximum sensitivity to NO gas in dry air at an operating temperature as low as 200˚C. We also found that these CuO nanorod gas sensors showed reversible and reliable electrical response to NO gas at a range of operating temperatures. These results would indicate some potential applications of the p-type semiconductor CuO nanorods as promising sensing materials for gas sensors, including various types of p-n junction gas sensors.