In this study, the performance was checked and the optimal conditions were found by machining the inner surface of a round pipe using the magnetic abrasive finishing method. In this experiment, an AL 6063 pipe was used as a sample. To check the performance of magnetic abrasive finising, the machining effect of different abrasive particle mixing ratio, rotation speed, and magnetic pole arrangement was analyzed through surface roughness (Ra) and weight removal measurement. The optimum mixing ratio was 3:1 of electrolytic iron to magnetic abrasive particles, the rotational speed was 1600rpm, and the best surface roughness was obtained in the N-S-N arrangement of magnetic poles.

A magnetic abrasive finishing process was proposed for improving the surface accuracy of microscale -diameter STS 304 bar used in many applications such as, medical, aerospace, and nuclear industries. Most of the previous research has already explored the conventional finishing technique to improve the accuracy of material in terms of the surface roughness. However, their results are still not good enough for the requirement in the today’s engineering industry. Especially, when the workpiece is a material of microscale-diameter, use of such conventional processes becomes impossible because they entail the application of high pressures that may damage the surface to be finished. Moreover, less control is available over these conventional finishing processes. In this study, an ultra-high-precision magnetic abrasive finishing process was applied to the precision machining of microscale-diameter STS 304 bar and the experimental work are performed with many critical parameters such as, different workpiece revolution speeds, abrasive grain sizes, different finishing temperatures, and pole vibrations. The results showed that in The initial surface roughness of 0.20 μm (Ra) was decreased to 0.025 μm with 0.5 μm of abrasive grain size and pole vibration 12Hz at 40,000 rpm.

sesses the finishing capabilities for application to high-precision machining. Because Ti-6AL-4V (Eli) is widely used in applications where it is exposed to the human body, the industrial grinding oil that is commonly used in the magnetic abrasive finishing process was replaced by vegetable oils; the processing performances of these different grinding oils were compared and verified. The characteristics of magnetic abrasive finishing were also investigated according to the temperature of the material. The experimental results show that olive oil yields a surface roughness improvement of 87%. Also, in terms of the roundness and the amount of material removal, the performance was excellent. This demonstrates the possibility of replacing the conventional industrial oil for grinding. Furthermore, when olive oil was used at different temperatures, the finishing characteristics at room temperature were the most excellent. SEM and EDX analyses of the machined components (before and after processing) showed that the material composition was not changed. Additionally, the magnetic abrasive tool composition was not found on the surface of the finished samples. In conclusion, the possibility of using vegetable oil as the grinding oil for high-precision machining of Ti-6Al-4V (Eli) bars via a magnetic abrasive finishing process at room temperature conditions was verified.

Magnetic abrasive finishing (MAF) process is a surface improvement method, which the magnetic field of permanent magnet or electromagnet is used to control the abrasive particles during the finishing process. The magnetic abrasive tools are filled between the N-pole and S-pole of Nd-Fe-B type permanent magnets. Tungsten carbide bar (WC) is a high hardness material and its compressive strength is much higher than the other materials. Therefore, due to its superior mechanical properties, it has been widely used in cutting or machining process. Because the smooth surface of tungsten carbide is required in cutting tools, thus the magnetic abrasive finishing process was applied for achieving its surface accuracy and dimensional accuracy. The results showed that the surface roughness of tungsten carbide bar was improved from Ra: 0.23㎛ to Ra: 0.02㎛ in 120 sec by magnetic abrasive finishing process.

In this research, the magnetic abrasive finishing process using (Nd-Fe-B) permanent magnet was applied to confirm the performance and to find the optimum conditions. The STS304 bar was used as the specimen in this experiment. In order to confirm the performance of magnetic abrasive finishing process, the surface roughness (Ra) and diameter reduction were measured when the specimens were processed under the conditions of rotational speeds, frequencies, and magnetic pole shapes. The rotational speeds were varied at 8000rpm, 15000rpm, 20000rpm, and 25000rpm. And the frequencies were changed to 0Hz, 4Hz and 10Hz. Also the shapes of the magnetic pole were changed to flat edge, sharp edge and round edge. It can be concluded that the surface roughness (Ra) and diameter reduction were found to be the best at 25000rpm, 4Hz, flat edge.

In this paper deals with behavior of the magnetic abrasive using Ba-Ferrite on polishing characteristics in a new internal finishing of STS304 pipe applying magnetic abrasive polishing. The magnetic abrasive using Ba-Ferrite grain WA used to resin bond fabricated low temperature. And Ba-Ferrite of magnetic abrasive powder fabricated that Ba-Ferrite was crused into 200 mesh. The previous research have made an experiment in the static state the movement of magnetic abrasive grain is nevertheless in the dynamic state. In this paper, We could have investigated into the changes of the movement of magnetic abrasive grain. In reference to this result, we could have made the experiment which is set under the condition of the magnetic flux density, polishing velocity according to the form of magnetic brush.

Most of mold manufacturing procedures have been automated by the introduction of NC machine tool and CAD/CAM system. But the three-dimensional surface curvature of the mold must be done by hand work of well-skilled workers. Magnetic abrasive polishing powders were investigated for surface polishing for 3D curvature. This study aims to investigate homogeneously distributed hard phase in Fe matrix and strong bonding between Fe-matrix and hard phase. The NbC powder, powder and powder were mixed in Fe-matrix respectively. Mixed Fe-hard phase powders were compacted by press and then these were melted by plasma melting. According to SEM, XRD and OM observation, Fe-NbC magnetic abrsive powder had the most homogeneous distribution and strong bonding. As a result of magnetic polishing, the surface roughness before magnetic polishing, 1 , was reduced to 0.2 over the entire inner surface of the tube.