프리스트레스(PS) 긴장재의 긴장력 관리는 거더 성능관리에 있어 매우 중요한 항목이나 현재는 시공시 설계 긴장력의 도입 여부만을 검증한 후 공용시에는 그 관리가 이루어지지 않는 실정이다. 이에 본 연구에서는 PSC 거더의 제작단계에서부터 공용시까지 생애주기 동안의 긴장력 관리가 가능한 PSC 거더를 제안하기 위한 기초 연구로서, 현재의 기술수준으로 사용 가능한 센서들을 이용하여 PS 긴장력을 측정하는 실험 연구를 수행하였다. 소규모 거더를 제작하여 4종류의 센서를 설치하였고, 긴장력을 도입하면서 각 센서들의 적용성과 정확성을 평가하였다. 실험결과에 따르면, 중공로드셀은 편심하중이 작용하는 경우 기준값보다 하중을 높게 평가하는 경향이 있었다. EM 센서는 실용이 가능한 정확도를 보여주었으며, 콘크리트 내부의 긴장재를 따라 어느 위치에서도 설치할 수 있다.

본 논문에서는 PSC 거더 내부 긴장재의 Prestress 변화를 계측하고, 그 손실을 관리하기 위하여 PSC 거더 내부에 매립이 가능한 매립형 EM 센서를 연구 및 제작하였다. 현재까지의 PSC 내부 긴장재의 긴장력 손실관리는 시공 시 설계 긴장력 도입 여부 검증에 머물러 있으며, 시공 후에는 관리가 제대로 이루어지고 있지 않다. 이에 본 논문에서는 강자성체에 자기장이 작용하면 비투자율인 강자성체 고유의 특성이 변화한다는 탄성-자기 이론을 기초로, PSC 거더의 정착구와 쉬스관 외관의 특성을 반영하여 PSC 거더 내부에 매립이 가능한 매립형 EM 센서를 설계하여 제작하였다. 제작 후에는 그 성능을 검증하기 위하여 소형 PSC 거더 모형에 제작된 매립형 EM 센서를 설치한 후 콘크리트를 타설하였다. 양생이 종료된 후 7가닥의 PS 텐던을 삽입한 후 텐던에 200, 710, 1070, 1300kN의 긴장력을 도입하면서 매립형 EM센서를 통해 비투자율의 변화를 계측하였다. 계측 결과 도입한 긴장력이 커질수록 PS 텐던의 비투자율이 낮아지는 변화가 있음을 확인하였으며, 도입 긴장력에 따른 투자율이 도입 긴장력을 충분히 추정할 수 있음을 확인하였다. 따라서 본 연구에서 제안한 매립형 EM 센서는 PSC교량 내부로 매립이 가능함을 확인하였으며 매립형 EM 센서를 통한 비투자율 변화 계측을 통하여 PS 텐던의 긴장력 변화를 추정할 수 있음을 확인하였다.

In this paper, we present the result of analytical investigation pertaining to the structural behavior of steel-concrete composite plate girder with arch-type web stiffener. In the arch-type web stiffener located in the compression side of web, infill concrete is cast to strengthen the arch-type stiffener and also to exert resisting force against compression force. This type of composite steel-concrete plate girder bridge is built and is in service. To understand the behavior thoroughly, analytical parametric study was conducted by using the finite element method. As a result it was found that the effect of arch-type stiffener with infill concrete is considerable for the design of such type composite girder bridge.

본 논문에서는 교량, 선박 등에 사용하고 해양환경을 고려한 알루미늄 합금(A6082-T-6) 플레이트 거더의 물리적 관계를 살펴보고자 한다. 플레이트 거더는 제품수명주기에 이동하중, 적재하중 등 같은 패치로딩을 경험하게 된다. 이 하중을 받는 알루미늄합금 플레이트 거더의 최종강도에 대해 다수 수치모형을 적용하여 탄소성 대변형 시리즈 해석을 수행하고 회귀분석을 통해 예측식을 제안하였다. 예측식은 최종강도와 세장변수의 상관관계로 나타냈으며 세장변수가 낮을 경우(0-2.3) 약 9 % 정도 오차가 발생하며 높을 경우(2.3-4.0) 약 1-2 % 정도 오차가 발생하였다. 따라서 제안 예측식 적정성은 합리적으로 평가할 수 있는 것으로 확인되었다.

The domestic and foreign specifications presented the effective width based on flange length to width ratio only. The existing paper on the effective width grasped of the effect of span, load type and cross-section properties, but localized steel bridges. Recently, The studies are going on in progress for the application of fiber reinforced composite material in construction field. Therefore, it is required to optimum design that have a good grasp the deformation characteristic of the displacements and stresses distribution and predict variation of the effective width for serviceability loading. This research addresses the effective width of all composite material box girder bridges using the finite element method. The characteristics of the effective width of composite structures may vary according to several causes, e.g., change of fibers, aspect, etc. Parametric studies were conducted to determine the effective width on the stress elastic analysis of all composite materials box bridges, with interesting observations. The various results through numerical analysis will present an important document for construct all composite material bridges.

Prestressed concrete (PSC) is a method in which prestressed tendon is placed inside and/or outside the reinforced concrete member and the compressive force applied to the concrete in advance to enhance the engineering properties of concrete member which is weak under tension. In this paper we suggested the precast PSC girder assembled with segments of portable size and weight at the factory. The segments of precast PSC girder will be delivered and assembled as a unit of PSC girder at the site. Consequently, we suggested new-type of precast segmented PSC girder with different shapes of segment cross-section (i.e., I-shape, Box-shape). To mitigate the problems associated with the field splice between the segments of precast PSC girder anchor system is attached near the neutral axis of the girder and relatively uniform compression throughout the girder cross-section is applied. Prior to the experimental investigation, analytical investigation on the structural behavior of precast PSC girder was performed and the serviceability (deflection) and safety (strength) of the girder were confirmed. In addition, 4-point bending test on the girder was conducted to investigate the structural performance under bending. From the experimental investigation, it was found that the precast PSC girder spliced with 3 and 5 segments has sufficient in serviceability and safety conditions and it was also observed that the point where the segments spliced has no defects and the girder behaves as a unit.

평면내 곡선교량은 편심하중뿐만 아니라 자중만으로도 비틀림하중을 받게 되고, 이는 지점부 부반력 발생의 원인이 된다. 본 논문에서는 경간장 48.8m를 가지는 단경간 곡선강박스 거더교량에 대해 내부곡률각도를 0.49∼1.35rad으로 조정하면서 곡률효과에 따라 지점에서 발생하는 수직반력을 분석하였다. 부반력 발생가능성을 고려하여 반력 크기 및 방향을 예측하기 위해 곡선교량 상부구조를 각 독립된 요소로 분리하여 반력산정식을 해석적으로 개발하였다. 콘크리트 바닥판 및 강재 하부플랜지는 각각 면의 차원을 가지는 기학학적 환형섹터로, 수평면내에서 폭이 좁게 투영되어 나타나는 상부플랜지 및 복부판은 선의 차원을 가지는 기하학적 호로 가정되었다. 제안된 반력산정식의 형식은 비교적 단순하고 그 예측값은 유한요소해석으로 얻은 값과 비교하였을 때 오차가 1% 수준으로 잘 일치하였다.

본 논문에서는 도로교 설계기준이 개편됨에 따라 변화된 활하중과 설계식의 검토를 하려한다. 이를 위해 강합성 플레이트 거더교와 PSC 거더교를 이용한 두 예제를 살펴본다. 기존 도로교설계기준 하중과 AASHTO LRFD 하중 그리고 새로 개편된 도로교설계기준 2015 한계상태설계법에 나온 하중을 적용하여 횡분배 계수법과 유한요소 격자해석을 통해 구한 포락선을 비교․검토한다. 또한 강합성 플레이트 거더교의 경우 중앙지간의 길이 변화에 대한 검토를 하고, PSC 거더교의 경우에는 가로보의 개수와 경간의 개수, 그리고 각 경간장의 변화를 주어 각각 그 차이점을 분석한다.

Prestressed concrete PSC girders are efficient in terms of structural performance, economical efficiency and constructability. However, PSC girders have overtuning risk in construction in which extra work needs to protect. The low center of gravity girder (MPC girder) is more stable and easier to construct than the traditional PSC girder, which has tweaked end point and mono-tendon anchor. In this study, we evaluated the structural advantages in the deflection (slope) and stress on the link slab by using the finite element method. As a result, it was found that the reinforcement in the link slab for the bridge continuation may be reduced because of less displacement.

This study investigates strength of unstiffened flanges in horizontally curved box girders under different curvature by using Abaqus 6.13 which is finite element method program. When horizontally curved girder is subjected to simple vertical load, bending moment and torsional moment occur at the same time different from straight girder. This torsional moment cause torsion and distortion on box section. Because of such phenomenon, longitudinal stress is non-uniformly distributed on flange of curved box girder. Non-uniformely distributed stress make strength of flange lower. Although demand of curved girder is increasing due to complexification of urban, it is only AASHTO(2012) that has certification for curved girder. But equation for curved girder in AASHTO(2012) neglect almost of curvature effect. Box girder is usually used for curved girder due to their superb torsional properties. So, we need more study for strength of curved box girder flange.

In curved I-girder systems, stability is mainly provided by interconnecting cross-frames or diaphragms. These members act as primary load carrying component thus proper design and analysis must be made. This study proposes improvement on the existing cross-frame spacing limit for horizontally curved girder systems utilizing buckling capacities. Eigenvalue analysis was conducted using the finite element program, ABAQUS. Maximum cross-frames spacing (Smax) was computed with varying degree of curvature, flange width-to-depth ratio ( ) and span length-to-depth ratio (L/d). Models were then generated and their buckling modes and critical buckling capacity ratios were obtained. Lastly, a suggestion was developed based on the results of the finite element analysis to provide a better guide on the design of cross-frame spacing limit. The suggested limit was then compared to the existing cross-frame limit to verify the improvement on the cross-frame spacing.

In this study, a real-scale specimen of Steel-Confined Prestressed Concrete (SCP) composite girder was tested in a three points bending. Furthermore, vibration tests were performed to verify the dynamic stability of the SCP composite girder for railway bridges. The results of the experimental test were similar to stable rigidity behavior until the static actuator limit load (6300 kN). That is, the SCP composite girder showed a stable rigidity behavior in the ultimate load (3,174 kN) as well as the service load (1,076 kN). Finally, the possibility of resonance of the SCP composite girder has been found to be low.

This paper introduces general concepts of jointless bridges and field construction case of semi-integral bridge with psc girder integrating end-diaphragm. The expansion joints need to satisfy thermal and safety conditions of bridges. General bridges with joints have some problems, which are frequently replacement cycle time from mechanical damage or unstable movement, maintenance cost and more. To solve these problems, Integral Abutment Bridges(IAB) have been applied overseas in the 1930s. In Korea, first IAB was constructed in the early 2000s and precast IAB systems was invented and applied lately. Kyungshin overpass bridge in Incheon is the Semi-IAB constructed, the span length is 2@35=70m and the width is 13.9m. The original plan was to use general joint bridge but design field changed with expectations for advanced economic estimation and maintenance. This changed method of B.I.B bridge construction provided not only workability, construction cost but also safety improvement at the same time.

본 연구에서는 실험 모형을 이용한 탄소성 대변형 시리즈 해석을 수행하여 플레이트 거더의 파손모드와 최종하중을 예측하였다. 수치해석 모형의 붕괴모드는 재하 시 플랜지에서 소성 힌지가 형성되었으며 실험모형의 붕괴모드와 일치하였다. 또한, 웹에서 항복선이 형성되어 크리플링 붕괴모드가 발생하는 것을 관찰할 수 있었으며 각각의 실험모형과 수치모형 최종하중의 평균값 1.07, 표준편차 0.04, 변동계수 0.04로 선형성을 유지하였으며 전체 최종하중 결과도 대략 8 % 오차를 나타내었다. 이는 수치모형 결과가 실험 및 적용 기준에 매우 만족하고 양호한 결과를 도출하였다고 생각한다. 따라서 알루미늄합금 플레이트 거더의 최종하중 예측 시 실험 및 적용 기준과 함께 병행하여 적용을 한다면 이에 대한 합리적 안전수준을 유지한다면 더 효율적이고 경제적 알루미늄 합금 플레이트 거더의 파손모드 및 최종하중에 대해 예측할 수 있을 거라고 생각한다.

The curved bridges shows very complicate behaviors compare to straight girders due to its initial curvature. Usually, the shear strength is investigated due to the aspect ratio(transverse stiffeners spacing/height of girder) and many researches have been conducted for the web shear strength for I-shaped curved girders with high aspect ratios(larger than 3). In this study, numerical studies are carried out and the results are compared with the current design practices. By the analyses, the maximum aspect ratio of a transversely stiffened web panel are suggested to revisits the validity of a limited imposed by Basler.

Compare to straight girders, horizontally curved girder shows complicate behaviors because the bending moments and torsional moments are always acting simultaneously. Because of non-uniform torsion, one edge of compression flange is yielded faster than the other edge due to combined vertical and lateral moments. Hence, the strength of cross section need to be investigated with the effect of initial curvature. The design specifications, however, does not consider the curvature effect. In this study, as a basic research, the parametric studies are performed to understand the flange local buckling behaviors of horizontally curved girders.

This paper introduces general concepts of Jointless Bridges and field construction case of Semi-Integral Bridge with PSC girder integrating end-diaphragm. The expansion joints need to satisfy thermal and safety conditions of bridges. General bridges with joints have some problems, which are frequently replacement cycle time from mechanical damage or unstable movement, maintenance cost and more. To solve these problems, Integral Abutment Bridges(IAB) have been applied overseas in the 1930s. In Korea, first IAB was constructed in the early 2000s and precast IAB systems was invented and applied lately. Kyungshin overpass bridge in Incheon is the Semi-IAB constructed, the span length is 2@35=70m and the width is 13.9m. The original plan was to use general joint bridge but design field changed with expectations for advanced economic estimation and maintenance. This changed method of B.I.B bridge construction provided not only workability, construction cost but also safety improvement at the same time.