In this paper, the adsorption removal characteristic for 10 species of perfluoroalkyl and polyfluoroalkyl substances (PFAS) was investigated using GAC and modified GAC (GAC-Cu). After modification with Cu(II), the amount of copper was to 1.93 and 4.73 mg/g for GAC and GAC-Cu, respectively. The total amount of 10 species of PFAS per specific area was obtained to 0.548 and 0.612 ng/m2 for GAC and GAC-Cu, respectively. A series of batch test confirmed lower efficiency was observed with a smaller number of carbon chain length and the removal efficiency of PFCA (perfluoroalkyl carboxylic acids) was lower than that of PFSA (perfluoroalkyl sulfonic acids) with the same carbon chain length. Regarding the pH effect, the adsorption capacity was decreased with increase of pH due to the increase of electrostatic repulsion. According to pseudo first and second order (PFO and PSO) kinetic models, while the values of equilibrium uptake and time did not show significant difference, a difference in uptake was observed between 24-48h. Furthermore, based on correlation analysis, Log Kow and uptake have a high correlation with molecular weight (M.W.) and initial concentration, respectively. These results show that long-chain PFAS have higher removal efficiency due to their increased hydrophobicity.

Tc-99 is considered as one of the major fission products in the context of disposal of spent nuclear fuel, due to the long half-life and chemical stability. In the atmospheric aqueous solutions, Tc is expected to exist in the form of TcO4 ‒ and thus is considered as an environmental concern according to its high solubility and mobility. Therefore, the development of an effective and economically viable adsorbent for aqueous Tc(VII) is imperative from the perspective of decontamination and remediation of contaminated environments. In this work, the adsorption behaviors of Re(VII), as a chemical surrogate of Tc(VII), onto the bentonites modified with two different organic cations such as hexadecyl pyridinium (HDPy) and hexadecyl trimethylammonium (HDTMA) were quantitatively analyzed and compared with each other. For the sorption experiment, adsorbents were prepared by surface modification of bentonite. Before the modification, the initial bentonite was pre-treated with 1 M NaClO4 and then reacted with HDPy or HDTMA. The modification process was performed at room temperature for 24 hours with various concentrations of organic cations, which were set to a range of 50-400% compared to the cation exchange capacity (CEC) of bentonite. After the reaction, the dried and crushed modified bentonites were filtered with the sieve with a mesh size of 63 μm. Aqueous Re(VII) solutions were prepared by dissolution of NH4ReO4 (Sigma-Aldrich) in deionized water with three different Re(VII) concentrations of 10-4M, 10-5M, and 10-6M. After that, the modified bentonite and the aqueous Re(VII) solutions were mixed at a liquid-to-solid ratio of 1 g/L. Aliquots of the samples were extracted for quantification analysis with ICP-MS after syringe filtration (pore size: 45 μm) at reaction times of 10, 50, 100, and 500 minutes. According to the results, a considerably fast adsorption reaction of Re(VII) onto all modified bentonites was observed, revealing exceptional sorption affinity of HDPy- and HDTMA-modified bentonites. For both organic cations, bentonites modified with the concentrations of organic cations ranging from 200 to 400% relative to the CEC of bentonite showed almost complete removal of aqueous Re(VII). For bentonites modified with lower concentrations of organic cations, the HDTMA presented a relatively larger sorption capacity than the HDPy. The result obtained through this study is expected to be referred to as a case study for the synthesis of cost-efficient and highly effective adsorbent material for highly mobile anionic radionuclides such as I‒ and TcO4 ‒.

In this study, superior carbon nanotubes (CNT) were chemically modified with itaconic acid (IA) and a polyaniline (PANI) composite was formed and used to remove methylene blue (MB) dye from an aqueous solution. The capacity of CNTs modified with IA (IA/CNT) and composited with PANI (PANI/CNT) to remove MB dye from an aqueous solution was compared and investigated. The effects of parameters such as pH (3–10), adsorbent dose (0.8–8 g/L), initial dye concentration (10–100 mg/L), and temperature (25–55 °C) on MB adsorption were investigated. IA/CNT and PANI/CNT adsorbents were characterized by analyzes such as Fourier Transform Infrared Spectroscopy (FT-IR), Field Emission Scanning Electron Microscopy (FE-SEM), transmission electron microscope (TEM), and Brunauer, Emmett and Teller (BET). It was determined that the isotherm data fit the Langmuir isotherm model. The maximum adsorption capacity (qmax) of PANI/CNT and IA/CNT calculated according to this model (at 25 °C) was 12.78 and 32.78 mg g− 1, respectively. Thermodynamic analysis results showed that the adsorption was exothermic, feasible, and spontaneous. It can be said that the possible mechanism of MB on PANI/CNT and IA/CNT adsorbents occurs with the participation of π–π interaction, electrostatic attraction and hydrogen bonding.

In the case of decommissioning of a nuclear power plant, it is expected that a significant amount of VLLW and LLW that need to be disposed of are also expected. Conventional reduction technology is a method of extracting or removing radionuclides from waste, but this project is being carried out for the purpose of obtaining a reduction effect through the development of a material that treats another radioactive waste using radioactive waste. In this paper, the technology of impregnating LiOH capable of adsorbing radiocarbon to the gas filter material manufactured from concrete and soil waste as raw materials and the radiocarbon removal performance were reviewed. In this study, a raw material of ceramic filter was prepared by mixing concrete and soil waste with a powder of 40 m or less, and after sintering at 1,250°C, 5wt% to 40wt% of LiOH is impregnated with a filter capable of adsorbing carbon dioxide. was prepared. The prepared filter used ICP-OES and XRD to confirm the LiOH deposition result, and the concentration of carbon dioxide discharged through the carbon dioxide adsorption device was confirmed. It was possible to obtain the result that the amount of adsorption was changed depending on the flow rate of carbon dioxide supplied and the amount of material. Through this, it was possible to confirm the possibility of power generation in the adsorption performance of gas. In this study, after crushing waste concrete and waste soil, powders of 40 m or less were mixed with other additives to prepare raw materials for ceramic filters, and sintered at 1,250°C to manufacture filters. 5wt% to 40wt% of LiOH was impregnated on the prepared filter to give functionality to enable carbon dioxide adsorption. The results of LiOH deposition were confirmed using ICP-OES and XRD, and the change in the concentration of carbon dioxide emitted through a separately prepared adsorption device was confirmed. It was possible to obtain the result that the amount of adsorption was changed according to the flow rate of carbon dioxide supplied and the amount of material, and the possibility of developing a material for radioactive waste treatment using radioactive waste was confirmed when the porosity and specific surface area of the filter material were increased.

This work using first-principles theory proposed PdN3- doped CNT ( PdN3-CNT) as a potential gas sensor for detection of NO, NO2 and O3 in the air insulated equipment, to evaluate its operation status. Results indicate that the PdN3- CNT behaves chemisorption upon three gas species, with adsorption energy (Ead) of − 2.15, − 1.91 and − 1.96 eV, and charge-transfer (QT) of − 0.141, − 0.325 and − 0.419 e, respectively. The band structure (BS) and density of state (DOS) analysis reveal that the gas adsorptions cause remarkable deformations in the electronic property of the PdN3- CNT, leading to the increase of the bandgap for the gas adsorbed systems and verifying the strong binding force of the bonded atoms from the orbital DOS. Combined with the results by frontier molecular orbital theory, we presume that PdN3- CNT is a promising sensing material to be explored as a resistance-type gas sensor for detection of NOx with higher electrical response upon NO. It is our hope that our theoretical assumption could be further studied and realized in the following experiential research, which would be meaningful to propose novel sensing candidate in the field of electrical engineering to guarantee the safe operation of the air insulation equipment.

Numerous chemical modifications on activated carbon such as acidic conditioning, thermal treatment and metal impregnation have been investigated to enhance adsorption capacities of micropollutants in water treatment plants. In this study, chemical modification including acidic, alkaline treatment, and iron-impregnation was evaluated for adsorption of 2,4-dichlorophenol (2,4-DCP). For Fe-impregnation, three concentrations of ferric chloride solutions, i.e., 0.2 M, 0.4 M, and 0.8 M, were used and ion-exchange (MIX) of iron and subsequent thermal treatment (MTH) were also applied. Surface properties of the modified carbons were analyzed by active surface area, pore volume, three-dimensional images, and chemical characteristics. The acidic and alkaline treatment changed the pore structures but yielded little improvement of adsorption capacities. As Fe concentrations were increased during impregnation, the active adsorption areas were decreased and the compositional ratios of Fe were increased. Adsorption capacities of modified ACs were evaluated using Langmuir isotherm. The MIX modification was not efficient to enhance 2,4-DCP adsorption and the MES treatment showed increases in adsorption capacities of 2,4-DCP, compared to the original activated carbon. These results implied a possibility of chemical impregnation modification for improvement of adsorption of 2,4-DCP, if a proper modification procedure is sought.

Tin bis(monohydrogen orthophosphate) monohydrate 물질의 흡착 성질에 관하여 KCl 수용액을 통하여 조사하였다. 금속이온 농도와 pH를 변화시키면서 어떻게 달라지는지 화학평형에 바탕을 두고 data를 분석하였다. 금속이온들의 흡착 data는 Langmuir 흡착식에 넣어 Langmuir 수치들을 얻는데 사용되었다. Tin phosphate는 산성에서 이온교환 화합물로 작용하였으며, 2가의 전이금속이온에 대해 Cu+2 > Co+2 > Ni+2의 순서로 선택적 흡착성질을 나타내었다. 약한 산성 이온 교환체에서와 같이 금속이온의 교환은 tin phosphate의 선택성을 결정하는데 결정적 역할을 하였다. 모든 경우에서 흡착의 정도는 온도와 농도의 증가와 함께 증가하였다. Lnngmuir 수치들은 흡착과정 동안의 엔트로피, 엔탈피, 자유에너지 변화량같은 열역학적 함수들을 계산하는데 이용되었다.

In this study, the flat glass and adsorption pad were modeled using SolidWorks Simulation, to understand the deformation characteristics of the vertical flat glass by the adsorption pressure during vertical transport of LCD. The horizontal and vertical displacements and equivalent stresses of the flat glass were investigated by the structural analysis. From the displacement and stress visualization according to the adsorption pressure, the higher the adsorption pressure, the larger the glass surface protruded. The horizontal deformation of flat glass increased with increasing thickness and the vertical deformation increased with decreasing thickness. In addition, the maximum equivalent stress applied to the flat glass increased significantly as the adsorption pressure increased and the thickness decreased. As a result of the structural analysis, the thinner the thickness of the plate glass, the greater the effect on the adsorption pressure. Especially, the effect of the adsorption pressure was clearly observed at the thickness of 0.5mm.

In this study, the physicochemical characteristics and fluoride adsorption capacity of the bone char pyrolyzed at different temperatures; 200℃, 300℃, 350℃, 400℃, 500℃, 600℃, and 700℃ were investigated. Analytical studies of the synthesized bone char including; SEM-EDS, XRD, BET and FT-IR, showed the presence of hydroxyapatite(HAP), which is the main substance that adsorbs fluoride from aqueous solutions containing high fluoride concentrations. Bone char pyrolyzed from 350∼700℃ specifically revealed that, the lower the temperature, the higher the fluoride adsorption capacity and vice versa. The loss of the fluoride adsorption function of HAP (OH- band in the FTIR analysis) was interpreted as the main reason behind this inverse correlation between temperature and fluoride adsorption. Bone char produced at 350°C hence exhibited a fluoride adsorption capacity of 10.56 mgF/g, resulting in significantly higher adsorption compared to previous studies.

Fibrous adsorbents, such as activated carbon fibers (ACF) have acknowledged advantages of rapid adsorption rate and ease of modification compared with granular and powdered adsorbents. Based on the surface modification of lyocell-based ACF, we observed different surface characteristics of ACF samples with variation in the mixing ratio and impregnation time of H3PO4, NaCl, and KMnO4 solution. For an engineering application, we also explored the adsorption characteristics of thusproduced ACF samples onto volatile organic compounds (VOCs). Isothermal adsorption experiments were performed using toluene and benzene as adsorbates. Results indicate that both physical and chemical surface properties have an effect on the adsorption of volatile organic compounds (VOCs).

To develop flexible adsorbents for compact volatile organic compound (VOC) air purifiers, flexible as-spun zeolite fibers are prepared by an electrospinning method, and then zeolite particles are exposed as active sites for VOC (toluene) adsorption on the surface of the fibers by a thermal surface partial etching process. The breakthrough curves for the adsorption and temperature programmed desorption (TPD) curves of toluene over the flexible zeolite fibers is investigated as a function of the thermal etching temperature by gas chromatography (GC), and the adsorption/desorption characteristics improves with an increase in the thermal surface etching temperature. The effect of acidity on the flexible zeolite fibers for the removal of toluene is investigated as a function of the SiO2/Al2O3 ratios of zeolites. The acidity of the flexible zeolite fibers with different SiO2/Al2O3 ratios is measured by ammonia-temperature-programmed desorption (NH3-TPD), and the adsorption/desorption characteristics are investigated by GC. The results of the toluene adsorption/desorption experiments confirm that a higher SiO2/ Al2O3 ratio of the flexible zeolite fibers creates a better toluene adsorption/desorption performance.

목 적 : 본 연구는 석시닐-키토산(succinyl-chitosan)을 합성하고 p(HEMA) 하이드로겔과의 상호 침투 고분자 구조 결합을 통해 제조한 콘택트렌즈의 물리적 성질 및 단백질 흡착특성에 대하여 알아보고자 한다. 방 법 : 키토산과 succinic anhydride를 교반하여 석시닐-키토산을 합성 한 다음 HEMA, EGDMA, NVP, AIBN을 공중합하여 건조시킨 콘택트렌즈와 상호침투가교방법으로 콘택트렌즈를 제조하였다. 제조된 콘택트 렌즈의 물리적 특성을 평가하기 위해 함수율, 접촉각, 광투과율, 표면의 거칠기를 측정하였으며, 인공눈물을 제조 한 다음 로리 단백질 정량법을 이용하여 단백질의 흡착특성을 평가하였다. 결 과 : 석시닐-키토산이 가교 되어 있는 콘택트렌즈의 경우 석시닐-키토산이 가교되어 있지 않은 대조 군에 비해 단백질 흡착량의 감소를 나타냈으며, 가교한 석시닐-키토산의 분자량이 클수록 단백질 흡착량이 감소하는 것을 알 수 있었다. 또한 석시닐-키토산의 분자량이 클수록 함수율은 증가하고 접촉각은 감소하여 습윤성의 증가를 확인할 수 있었다. 결 론 : 석시닐-키토산을 p(HEMA) 하이드로겔과 상호 침투 가교 하는 방법을 통해 기존의 콘택트렌즈가 가지는 물성을 해치지 않으면서 습윤성이 뛰어나고 단백질의 흡착을 줄일 수 있는 콘택트렌즈 제조가 가능 할 것으로 사료된다.

Adsorption technology can effectively handle the volatile organic compounds (VOCs) from waste gas. However the adsorption of VOCs at elevated temperature (>30oC) and high humidity conditions results in competitive adsorption between VOCs and the moisture. Furthermore, physical adsorption at an elevated temperature is the cause of degradation in the regeneration process performance. In this study, toluene as waste organic solvent in air at elevated temperature and high humidity was used to measure performance. The effects of the SiO2/Al2O3 ratio of zeolites, the adsorbent material coated on adsorption regenerative rotors, on the adsorption performance of toluene with respect to temperature (30~50oC) and relative humidity (50~90%RH) have been investigated. The adsorption of toluene decreased as relative humidity and adsorption temperature rose. The result shows that Htype ZSM5 (SiO2/Al2O3=100) zeolite exhibited the highest adsorption capacity for toluene at elevated temperature and humidity conditions. The physical and chemical adsorption of toluene on acid sites of zeolite were confirmed by this study.

프러시안 블루 유사체(Prussian Blue Analogue : PBA)는 3차원 구조와 기공을 갖는 금속-유 기골격체이며, 유기 리간드의 종류에 따라 다양한 구조를 갖는다. PBA는 바이오센서, 광학, 촉매, 수소 저장 장치 등의 분야에서 주목 받고 있으며 화학적 안정성을 가진 환경 친화적인 물질이다. 또한 다양 한 크기의 미세기공을 조정할 수 있어 흡착분야에서 많이 활용되고 있다. 본 연구는 수열합성법을 이용 하여 금속유기골격체인 Mn3[Fe(CN)6]2를 합성하였다. 전구체로 K4[Fe(CN)6]와 MnCl2를 사용하였고, 합 성된 물질은 소성하여 망간철산화물을 생성하였다. 실험 변수로 전구용액의 pH, 전구체의 몰농도, 반응 시간을 조절하여 입자의 크기와 형태에 대한 영향을 확인하였다. 합성된 다공체는 XRD, SEM, FT-IR, UV-Vis, TG/DTA에 의해 분석하였고, 여러 염료에 대한 흡착 특성을 평가하였다.

The characteristics of filter/adsorber granular activated carbon (F/A GAC) were investigated by measuring various parameters, which include surface area, pore volume, abrasion number, floater, and water-soluble ash. The correlation between parameters was also evaluated. Moreover, rapid small-scale column test (RSSCT) was conducted for adsorption characteristics. Thirteen F/A GAC were tested, and the average values of abrasion number and water-soluble ash were 88.9 and 0.15%, respectively. F/A GAC with the larger external surface area and greater mesopore volume had the lower abrasion number, which indicated that it was worn out relatively easily. Water-soluble ash of coconut-based GAC (about 2.6%) was greater than that of coal-based GAC (less than 1%), and the pH of solution was increased with GAC, which had the higher water-soluble ash. On the other hand, floater of thirteen F/A GAC was divided as two groups, which one group had relatively higher floater (2.7~3.5%) and the other group had lower floater (approximately 0.5%). The results of RSSCT indicated that coconut-based GAC (i.e. relatively higher water-soluble ash) had less adsorption capacity. Moreover, adsorption capacity of coal-based GAC with larger surface area and greater mesopore volume was superior to others.

정수슬러지를 탄화 및 활성처리하여 흡착제를 제조하였으며, 이를 이용한 황화수소 흡착특성을 고찰하였다. 제조 된 흡착제에 대한 BET측정 및 SEM 등 물성분석을 실시하였으며, 황화수소를 대상으로 회분식의 흡착평형실험 을 실시하였다. 실험변수로는 활성처리시 적용되는 약품종류 및 농도 등이 적용되었다. 실험결과, 정수슬러지는 탄화나 약품첨착과정을 통해 커다란 성능 향상이 이뤄짐을 알 수 있었다.