The estimation of heat source model is very important for heat transfer analysis with finite element method. Part I of this study used adaptive simulated annealing which is one of the global optimization algorithm for anticipating the parameters of the Goldak model. Although the analysis with 3D model which depicted the real situation produced the correct answer, that took too much time with moving heat source model based on Fortran and Abaqus. This research suggests the procedure which can reduce time with maintaining quality of analysis. The lead time with 2D model is reduced by 90% comparing that of 3D model, the temperature distribution is similar to each other. That is based on the saturation of heat transfer among the direction of heat source movement. Adaptive simulated annealing with 2D model can be used to estimate more proper heat source model and which could enhance to reduce the resources and time for experiments.

Forged part made of Cold heading quality wire materials are used for automotive brake systems. The cost reduction of forged products is a major issue because of the strict shape change. A series of studies were conducted to minimize the cost of EPB spindle process among brake parts. In order to reduce the material cost, heat treatment-abbreviated material was applied and the formability on the processes was verified by the ductile fracture theory. In addition, the causes of shape fixation and die life degradation were analyzed using the numerical simulation. The process cost has been minimized by re-designing process, changing the product shape, and the die material.

Ceramic membranes can be applied under extreme operating conditions such as low pH, high pressure and high temperature. In particular SiC has excellent mechanical properties and also has excellent properties related to membrane performance. However, high processing temperature increases cost of SiC products and thus limit’s its use. In this study oxidation bonding technique was used to fabricate cost-effective SiC microfiltration membrane at low temperature. The oxidation behavior at different thermal treatments was related with pore morphology and ultimately the membrane permeability. We have found that the membrane made by coating of oxidation bonded SiC layer over clay-bonded SiC support, sintered at 1000-1100°C could make a defect-free microfiltration membrane with pure water permeability above 700 LMH per bar. The membrane has narrow pore size distribution with average pore size about 0.1 μm.

This research carried out an analysis on input cost and leakage reduction effect by leakage reduction method, focusing on the project for establishing an optimal water pipe network management system in the Taebaek region, which has been executed annually since 2009. Based on the result, optimal cost-benefit analysis models for water distribution network rehabilitation project were developed using DEA(data envelopment analysis) and multiple regression analysis, which have been widely utilized for efficiency analysis in public and other projects. DEA and multiple regression analysis were carried out by applying 4 analytical methods involving different ratios and costs. The result showed that the models involving the analytical methods 2 and 4 were of low significance (which therefore were excluded), and only the models involving the analytical methods 1 and 3 were suitable. From the result it was judged that the leakage management method to be executed with the highest priority for the improvement of revenue water ratio was installation of pressure reduction valve, followed by replacement of water distribution pipe, replacement of water supply pipe, and then leakage detection and repair; and that the execution of leakage management methods in this order would be most economical. In addition, replacement of water meter was also shown to be necessary in case there were a large number of defective water meters.

  This paper considers a topological optimization of a computer network design with a cost constraint. The objective is to find the topological layout of links, at maximal reliability, under the constraint that the network cost is less or equal than a giv

본 논문에서는 강상자형교의 바닥판과 주형에 대한 생애주기비용(Life-Cycle Cost : LCC)를 고려한 최적설계 방법을 제안하였다. 생애주기비용의 최적설계 문제는 초기비용, 유지관리비용 그리고 강도와 처짐 그리고 균열에 대한 파손 기대비용의 최소화 문제로 정식화할 수 있다. 기존의 재래적인 설계방법과의 비교를 동해서 강상자형교의 생애주기비용 최적설계의 우수성을 입증하였다. 또한 수치적인 결과의 고찰을 통하여 LCC에 근거한 최적설계가 여타의 설계방법들보다 좀 더 합리적이고 경제적이며 안전한 설계를 유도하는 것으로 분석되었다.

This research provides optimization techniques for concrete mixture design for chloride penetration performance and cost. For optimization, objective functions are constructed with variables representing factors used in concrete mixture design process. Multi Objective Harmony Search Algorithm (MOHSA) is used for optimization and the result gives relationship between concrete’s chloride ion diffusivity and cost.

To lower the operational cost of microbubble generation by electrolysis, optimization of parameters limiting the process must be carried out for the process to be fully adopted in environmental and industrial settings. In this study, four test electrodes were used namely aluminum, iron, stainless steel, and Dimensionally Sable Anode (DSA). We identified the effects and optimized each operational parameter including NaCl concentration, current density, pH, and electrode distance to reduce the operational cost of microbubble generation. The experimental results showed that was directly related to the rate and cost of microbubble generation. Adding NaCl and narrowing the distance between electrodes caused no substantial changes to the generation rate but greatly decreased the power requirement of the process, thus reducing operational cost. Moreover, comparison among the four electrodes operating under optimum conditions revealed that aluminum was the most efficient electrode in terms of generation rate and operational cost. This study therefore presents significant data on performing costefficient microbubble generation, which can be used in various environmental and industrial applications.